HP Visualize J5000 Quick start guide
HP Visualize J5600 UNIX®Workstations
PA8600
Upgrade Instructions
Manufacturing Part Number: A5998-90000
Edition E1299
© Copyright 1999 by Hewlett-Packard
2
Notice
The information contained in this document is subject to change without
notice.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
Hewlett-Packard Warranty Statement
Refer to Warranty & Support for your HP Workstation for warranty terms
applicable to your Hewlett-Packard product and replacement parts.
Restricted Rights Legend
Use, duplication, or disclosure by the U.S. Government Department of
Defense is subject to restrictions as set forth in paragraph (b)(3)(ii) of the
Rights in Technical Data and Software clause in DFARS 252.227.7013.
© Copyright 1999 Hewlett-Packard Company. All Rights Reserved.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the
prior written consent of Hewlett-Packard Company.
UNIX is a registered trademark in the United States of America and
other countries, licensed exclusively through X/Open Company Limited.
© Copyright 1980, 1984 AT&T, Inc.
© Copyright 1979, 1980, 1983 The Regents of the University of
California.
3
This software and documentation is based in part on the Fourth Berkeley
Software Distribution under license from the Regents of University of
California.
4
5
1 Getting Started
The following important information must be adhered to for proper
removal and replacement of all Hewlett-Packard parts.
6Chapter1
Getting Started
Safety Warnings
Safety Warnings
WARNING Removing the device cover may expose sharp edges in the
equipment chassis. To avoid injury, use care when installing
customer add-on devices.
NOTE Before performing removal/replacement procedures, position the
workstation on a cushioned flat, stable surface, such as a table top or
workbench.
NOTE Installing the recommended HP replacement part in your J5000
workstation does not affect the regulatory and safety classifications or
approvals listed in the original owner’s guide.
Electrostatic Discharge (ESD) Precautions
To prevent damage to the J5000 workstation, observe all of the following
ESD precautions while performing removal and replacement procedures:
• Remove all ESD-generating materials from the work area in which
you will remove and replace the workstation field replaceable unit(s).
• Open the ESD materials provided with the replacement part kit.
Unfold the black conductive sheeting (antistatic mat) and place it
under a corner of the workstation.
• Wear a static strap to ensure that any accumulated electrostatic
charge is discharged from your body to ground. Attach the
static-grounding wrist strap by following the instructions on the
package. Attach the sticky end of the wrist strap to bare metal on the
rear panel of the workstation.
• Connect all equipment together, including the static-free mat, static
strap, clips attached to the wrist strap, nodes, and peripheral units.
Chapter 1 7
Getting Started
Safety Warnings
• Keep uninstalled printed circuit boards in their protective antistatic
bags.
• Once you have removed printed circuit boards from their protective
antistatic bags, handle the printed circuit boards by their edges only.
• Ensure you have a sufficient ESD protected area on which to lay out
the parts you remove from the system.
8Chapter1
Getting Started
Replacement Part Kit Contents
Replacement Part Kit Contents
Take a moment to verify that your kit contains the following contents:
• System board upgrade tray assembly
• Electrostatic Discharge (ESD) materials
• Removal/Replacement Instructions
If you are missing any part or any documentation, please call your
designated service representative.
Required Tools
You will need the following tools for removal/replacement procedures:
• T-10 and/or T-15 Torx drivers
• ESD materials
Chapter 1 9
Getting Started
Upgrade Instructions Overview
Upgrade Instructions Overview
The steps for performing the upgrade are outlined below and should be
performed in the sequence listed. Refer to individual sections of this
guide for step-by-step procedures for upgrading a J5000 to a J5600.
1. Prepare your workstation
- Verify that you have the correct version of HP-UX.
- Determine and WRITE DOWN the LAN ID of your system. You may
need to re-enter it after installing the new system board.
- Power off the workstation and any peripherals.
- Unplug the power.
2. Remove the front panel.
3. Remove the top panel.
4. Remove the side panels.
5. Disconnect the flex cable.
6. Remove the bus bar shield.
7. Remove the memory card(s) (DIMMs).
8. Disconnect the system board cables.
9. Remove the old system board.
10.Install the new system board.
11.Reconnect the system board cables.
12.Reinstall the memory card(s) (DIMMs).
13.Reinstall the bus bar shield.
14.Reconnect the flex cable.
15.Replace the side panels.
16.Replace the top panel.
17.Replace the front panel.
18.Verify system operations.
10 Chapter1
Getting Started
Preparing Your Workstation
Preparing Your Workstation
The workstation must be running HP-UX 10.20 with Additional Core
Enhancements (ACE4) 9906 or later to accommodate the PA8600
upgrade. It should report B.10.20. If the workstation is running an older
version of HP-UX, update the operating system software before
continuing. Use the command /usr/sbin/swlist -l bundle | grep ACE to
view what software products are loaded in your system. If the product
list includes B6193DA, you do not need to update HP-UX.
1. Determine the workstation’s LAN ID by entering the following
command: /usr/sbin/lanscan.
The output is similar to the following:
Hardware Station Crd Hardware Net-Interface NM MAC HP DLPI Mjr
Path Address In# State NameUnit State ID Type Support Num
2.0.2 0x08000970ECC0 0 UP lan0 UP 4 ETHER YES 130
Record the LAN ID here. You will need it after installing the new
system board:
Enter LAN ID: ___ ___ ___ ___ ___ ___ -___ ___ ___ ___ ___ ___
You must supply the dash (-) between the first six digits and the last
six digits
After you install the new system board and power on the system for
the first time, you may be prompted for the LAN ID.
2. Power down the system as described in the next section.
Other manuals for Visualize J5000
7
This manual suits for next models
1
Table of contents
Other HP Desktop manuals
HP
HP Kayak XA 05xx User manual
HP
HP A524x - Pavilion - 512 MB RAM User manual
HP
HP Neoware e370 - Thin Client User manual
HP
HP 9000 200 Series User manual
HP
HP Compaq dx2400 Operating and maintenance manual
HP
HP Pavilion w1000 - Desktop PC User manual
HP
HP A320m - Pavilion - 256 MB RAM User manual
HP
HP Workstation xw4100 User manual
HP
HP 8100 - Elite Convertible Minitower PC User instructions
HP
HP Workstation Z600 Manual
HP
HP Compaq d530 MT Manual
HP
HP Pavilion t400 - Desktop PC User manual
HP
HP P6230F Pavilion PC User manual
HP
HP Z1 G2 User manual
HP
HP Presario S7000 - Desktop PC General instructions
HP
HP D6030A - NetServer - E50 User manual
HP
HP Z800 - Workstation - 6 GB RAM User manual
HP
HP RP9 G1 9115 Installation instructions
HP
HP Compaq AlphaServer DS20E User instructions
HP
HP TouchSmart 610-1000 Instruction Manual
