HP Visualize c3600 Quick start guide
HP VISUALIZE C3600 UNIX®Workstations
PA8600
Upgrade Instructions
Manufacturing Part Number: A5997-90000
Edition E1299
© Copyright 1999 by Hewlett-Packard
2
Notice
The information contained in this document is subject to change without
notice.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by
copyright. All rights reserved. No part of this document may be
photocopied, reproduced or translated to another language without the
prior written consent of Hewlett-Packard Company.
Hewlett-Packard Warranty Statement
Refer to Warranty & Support for your HP Workstation for warranty terms
applicable to your Hewlett-Packard product and replacement parts.
Restricted Rights Legend
Use, duplication, or disclosure by the U.S. Government Department of
Defense is subject to restrictions as set forth in paragraph (b)(3)(ii) of the
Rights in Technical Data and Software clause in DFARS 252.227.7013.
© Copyright 1999 Hewlett-Packard Company. All Rights Reserved.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the
prior written consent of Hewlett-Packard Company.
3
UNIX is a registered trademark in the United States of America and
other countries, licensed exclusively through X/Open Company Limited.
© Copyright 1980, 1984 AT&T, Inc.
© Copyright 1979, 1980, 1983 The Regents of the University of
California.
This software and documentation is based in part on the Fourth Berkeley
Software Distribution under license from the Regents of University of
California.
4
5
1 Getting Started
The following important information must be adhered to for proper
removal and replacement of all Hewlett-Packard parts.
6Chapter1
Getting Started
CAUTION This upgrade process should be performed by experienced hardware
users only.
Chapter 1 7
Getting Started
Safety Warnings
Safety Warnings
WARNING Removing the device cover may expose sharp edges in the
equipment chassis. To avoid injury, use care when installing
customer add-on devices.
NOTE Before performing removal/replacement procedures, position the
workstation on a cushioned flat, stable surface, such as a table top or
workbench.
NOTE Installing the recommended HP replacement part in your B1000/C3000
workstation does not affect the regulatory and safety classifications or
approvals listed in the original owner’s guide.
Electrostatic Discharge (ESD) Precautions
To prevent damage to the B1000/C3000 workstation, observe all of the
following ESD precautions while performing removal and replacement
procedures:
• Remove all ESD-generating materials from the work area in which
you will remove and replace the workstation field replaceable unit(s).
• Open the ESD materials provided with the replacement part kit.
Unfold the black conductive sheeting (antistatic mat) and place it
under a corner of the workstation.
• Wear a static strap to ensure that any accumulated electrostatic
charge is discharged from your body to ground. Attach the
static-grounding wrist strap by following the instructions on the
package. Attach the sticky end of the wrist strap to bare metal on the
rear panel of the workstation.
• Connect all equipment together, including the static-free mat, static
8Chapter1
Getting Started
Safety Warnings
strap, clips attached to the wrist strap, nodes, and peripheral units.
• Keep uninstalled printed circuit boards in their protective antistatic
bags.
• Once you have removed printed circuit boards from their protective
antistatic bags, handle the printed circuit boards by their edges only.
Chapter 1 9
Getting Started
Replacement Part Kit Contents
Replacement Part Kit Contents
Take a moment to verify that your kit contains the following contents:
• System board upgrad tray assembly
• Electrostatic Discharge (ESD) materials
• Removal/Replacement Instructions
If you are missing any part or any documentation, please call your
designated service representative.
10 Chapter1
Getting Started
Required Tools
Required Tools
You will need the following tools for removal/replacement procedures:
• T-10 and/or T-15 Torque drivers
• ESD materials
• Sufficient ESD protected surfaces on which to lay out parts
This manual suits for next models
2
Table of contents
Other HP Desktop manuals
HP
HP D6030A - NetServer - E50 User manual
HP
HP 300 Series User manual
HP
HP Vectra VL series 8 Operating manual
HP
HP dx2355 - Microtower PC Operating and maintenance manual
HP
HP 510B - Minitower PC Manual
HP
HP dc7900 - Convertible Minitower PC Guide
HP
HP Pavilion Elite e9160f User manual
HP
HP DF300A - Portable Digital Picture Frame User manual
HP
HP ProDesk 400 G7 SFF Manual
HP
HP ProDesk 400 G1 User manual
HP
HP DC7600 - HP Operating and maintenance manual
HP
HP dc7800 - Convertible Minitower PC User manual
HP
HP Pavilion a210 Installation instructions
HP
HP Compaq Presario User manual
HP
HP Pavilion k200 - Desktop PC Installation instructions
HP
HP Pavilion t500 - Desktop PC Instruction manual
HP
HP Z Workstation series User manual
HP
HP Pavilion t500 - Desktop PC Instruction manual
HP
HP t5630 - Thin Client Installation and operating instructions
HP
HP Pavilion t467 User manual
