HP Visualize c160 User manual
RavenC160-180.FB -1 Wed Jul 10 14:00:20 1996
Installing the C160 to C180 CPU Upgrade
HP Part No. A4200-90018
E0796
Printed in USA
RavenC160-180.FB 0 Wed Jul 10 14:00:20 1996
Hewlett-Packard Co. 1996
Printing History
First Printing: July 1996
UNIX is a registered trademark in the United States and other countries,
licensed exclusively through X/Open Company Limited.
NOTICE
The information contained in this document is subject to change without
notice.
HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH
REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be lia-
ble for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copy-
right. All rights reserved. No part of this document may be photocopied,
reproduced or translated to another language without the prior written con-
sent of Hewlett-Packard Company.
RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by gov-
ernment is subject to restrictions as set forth in subdivision (c) (1) (ii) of the
Rights in Technical Data and Computer Software Clause at DFARS
252.227.7013. Hewlett-Packard Co., 3000 Hanover St., Palo Alto, CA
94304.
10 9 8 7 6 5 4 3 2 1
RavenC160-180.FB 1 Wed Jul 10 14:00:20 1996
1
Upgrading your Model C160 to a Model C180
Upgrading your Model C160 to a Model C180
Your upgrade kit contains a CPU board, which, when installed, upgrades
your Model C160 workstation to a Model C180 workstation.
The following sections provide step-by-step instructions for removing the
C160 CPU board and installing the C180 CPU board.
The general steps are outlined as follows. See the individual sections for
more detailed instructions.
NOTE: The following steps must be followed in the order in which they appear. Refer to the
individual sections of this guide for the actual step-by-step procedures for upgrading
the C160 to a C180.
• Determine the LAN ID of your system.
• Power off the workstation and any peripheral devices, unplug the power cords,
and disconnect any peripheral cables.
• Remove the main tray assembly.
• Remove the C160 CPU board from the main tray.
• Remove the memory boards from the C160 CPU board and reinstall them onto
the C180 CPU board.
• Install the C180 CPU board into the main tray assembly.
• Place the main tray assembly into the workstation chassis.
• Connect power cords and cables, restart the workstation, and enter the LAN ID
when prompted.
RavenC160-180.FB 2 Wed Jul 10 14:00:20 1996
2
Preparing Your Workstation
Preparing Your Workstation
1Determine the workstations LAN ID by entering the following at the prompt:
/usr/sbin/lanscan
The output is similar to the following:
Hardware Station Dev Hardware Net-Interface NM Encapsulation Mjr
Path Address lu State NameUnit State ID Methods Num
2.0.2 0x08000970ECC0 0 UP lan0 UP 4 ETHER 52
After you install the new CPU board or I/O board and power on the system for
the first time, you are prompted for the LAN ID. Record the information here so
you have a record of it:
EtherLAN ID ___________________-___________________
You must supply the dash (-) between the first six digits and the last six digits.
2Power off your workstation by pressing the power button on the front panel.
When you press the power button, the workstation automatically shuts down the
operating system before it powers off the system.
3When the workstation has completed shutting down and powering off, power off
the monitor, and any peripheral devices connected to the workstation.
4Unplug the power cord of the system unit, the monitor, and any peripheral devic-
es from ac wall outlets.
RavenC160-180.FB 3 Wed Jul 10 14:00:20 1996
3
Preparing Your Workstation
5Unplug the power cord from the back of the system unit.
WARNING: To avoid electrical shock, make sure you unplug the power cable from
the wall outlet and the system unit before proceeding any further.
CAUTION: The internal components of your workstation are susceptible to mechanical and
electrostatic shock. To prevent such damage from occurring, observe the following
precauxtions during the installation procedure.
•Stand on a static-free mat
•Wearastatic-groundingwriststrap to ensure that any accumulated electrostatic charge
discharges from your body to ground. Attach the static-grounding wrist strap by fol-
lowing the instructions on the package that contains the strap. Be sure to attach one
end of the strap to the system chassis.
6Disconnect all cables, connectors, and terminators from the connectors on the
front and rear of the system.
7Remove the system unit from the floor stand, as shown in Figure 1.
Figure 1 Removing the Floor Stand
RavenC160-180.FB 4 Wed Jul 10 14:00:20 1996
4
Preparing Your Workstation
8Lay the system unit on a flat surface, such as a table top.
9Attach a static-grounding wrist strap to bare metal on the back of the system unit.
RavenC160-180.FB 5 Wed Jul 10 14:00:20 1996
5
Removing the Main Tray Assembly
Removing the Main Tray Assembly
1Completely loosen the four thumb screws on the rear of the system unit, as shown
in Figure 2.
Figure 2 Removing Main Tray Assembly
2Place one hand on the top of the system unit and push, while pulling the handle
on the rear panel with your other hand. See Figure 2.
3Slide the main tray assembly out of the chassis.
Thumb Screws
Thumb
Screws
RavenC160-180.FB 6 Wed Jul 10 14:00:20 1996
6
Removing the Model C160 CPU Board
Removing the Model C160 CPU Board
1Remove the two CPU board retaining screws, as shown in Figure 3.
Figure 3 Removing the CPU Board
2Pull the two ejector handles at the same time, as shown in Figure 3.
3Slide the CPU board out approximately one inch, then lift it straight up to remove
it.
Retaining Screws
RavenC160-180.FB 7 Wed Jul 10 14:00:20 1996
7
Removing Memory Modules
Removing Memory Modules
1Locate the memory modules on the C160 CPU board, as shown in Figure 4.
Figure 4 C160 Memory Module Location
Memory Modules
RavenC160-180.FB 8 Wed Jul 10 14:00:20 1996
8
Removing Memory Modules
2To remove a memory module, push the ejector tabs on each side of the module.
Lift the memory module up and out of the connector and place it on a static-free
surface. Figure 5 shows how to remove a memory module.
Figure 5 Removing a Memory Module
Other manuals for Visualize c160
4
This manual suits for next models
1
Table of contents
Other HP Desktop manuals
HP
HP Pavilion d4600 - Desktop PC Specification sheet
HP
HP Compaq dx2390 User manual
HP
HP Pavilion t328 User manual
HP
HP Pavilion a400 - Desktop PC Specification sheet
HP
HP Compaq 8280 Elite CMT Business PC Assembly instructions
HP
HP CQ5110F - Presario - 3 GB RAM Use and maintenance manual
HP
HP A524x - Pavilion - 512 MB RAM Installation instructions
HP
HP TouchSmart 420-1100 User manual
HP
HP Compaq d530 MT Operating and maintenance manual
HP
HP ProOne 600 G3 User manual
HP
HP Vectra VT6 User manual
HP
HP Xw4300 - Workstation - 2 GB RAM User manual
HP
HP Compaq dc5850 User instructions
HP
HP Pavilion A6305 User manual
HP
HP Elite Slice G2 Manual
HP
HP TouchSmart ENVY 23-d055 User manual
HP
HP Pavilion t300 - Desktop PC User manual
HP
HP HP-16C User guide
HP
HP Media Center m400 - Desktop PC Specification sheet
HP
HP Kayak XU04 User manual
