HP Visualize b1000 Manual
HP VISUALIZE B Class and C Class UNIX®
Workstations
Parts Replacement Guide
Manufacturing Part Number: A4985-90036
Edition E0100
© Copyright 1999 by Hewlett-Packard
2
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright. All rights reserved. No part of
this document may be photocopied, reproduced or translated to another language without the prior written
consent of Hewlett-Packard Company.
Hewlett-Packard Warranty Statement
Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard
product and replacement parts.
Restricted Rights Legend
Use, duplication, or disclosure by the U.S. Government Department of Defense is subject to restrictions as set
forth in paragraph (b)(3)(ii) of the Rights in Technical Data and Software clause in DFARS 252.227.7013.
UNIX is a registered trademark in the United States of America and other countries, licensed exclusively
through X/Open Company Limited.
This software and documentation is based in part on the Fourth Berkeley Software Distribution under license
from the Regents of University of California.
© Copyright 1999 Hewlett-Packard Company. All Rights Reserved.
© Copyright 1980, 1984 AT&T, Inc.
© Copyright 1979, 1980, 1983 The Regents of the University of California.
Contents
3
1. Getting Started
Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . .5
Replacement Part Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Safely Powering Down the B Class and C Class Workstation . . . . . . . . .7
Product Exploded Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2. Parts Removal and Replacement
Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Removing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .10
Replacing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .11
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Removing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Replacing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Removing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Replacing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Removing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Memory Card(s) DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Removing and Replacing DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Removing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Replacing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
CD ROM Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4
Contents
Removing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Removing the Front-Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Replacing the Front-Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Removing the Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Hard Disk Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Putting a Disk Drive into its Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Replacing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
I/O Fan and Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing the I/O Fan and Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing and Replacing the Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Removing and Replacing the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . 37
Replacing the Fan and Speaker Bracket . . . . . . . . . . . . . . . . . . . . . . . 37
Removing and Replacing the System Board. . . . . . . . . . . . . . . . . . . . . . 38
Disconnecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Removing the old System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Replacing the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Real Time Clock (RTC) Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Removing the Real Time Clock (RTC) Module . . . . . . . . . . . . . . . . . . 42
Replacing the Real Time (RTC) Module . . . . . . . . . . . . . . . . . . . . . . . 43
Removing and Replacing the System Board Cooling Fans . . . . . . . . . . 44
Replacing the System Board Cooling Fans . . . . . . . . . . . . . . . . . . . . . 45
3. Wrapping Up
Verifying System Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Returning the Defective Exchange Assembly . . . . . . . . . . . . . . . . . . . 47
5
1Getting Started
The following important information must be adhered to for proper removal and
replacement of all Hewlett-Packard parts.
Safety Warnings
WARNING Removing the device cover may expose sharp edges in the equipment
chassis. To avoid injury, use care when installing customer add-on
devices.
NOTE Before performing removal/replacement procedures, position the workstation
on a cushioned flat, stable surface, such as a table top or workbench.
NOTE Installing the recommended HP replacement part in your B Class and C
Class workstation does not affect the regulatory and safety classifications or
approvals listed in the original owner’s guide.
Electrostatic Discharge (ESD) Precautions
To prevent damage to the B Class and C Class workstation, observe all of the following
ESD precautions while performing removal and replacement procedures:
• Remove all ESD-generating materials from the work area in which you will remove and
replace the workstation field replaceable unit(s).
• Open the ESD materials provided with the replacement part kit. Unfold the black
conductive sheeting (antistatic mat) and place it under a corner of the workstation.
• Wear a static strap to ensure that any accumulated electrostatic charge is discharged
from your body to ground. Attach the static-grounding wrist strap by following the
instructions on the package. Attach the sticky end of the wrist strap to bare metal on
the rear panel of the workstation.
• Connect all equipment together, including the static-free mat, static strap, clips
attached to the wrist strap, nodes, and peripheral units.
• Keep uninstalled printed circuit boards in their protective antistatic bags.
• Once you have removed printed circuit boards from their protective antistatic bags,
handle the printed circuit boards by their edges only.
6Chapter1
Getting Started
Replacement Part Kit Contents
Replacement Part Kit Contents
Take a moment to verify that your kit contains the following contents:
• The replacement part.
• Part Number: A3024-80004, Electrostatic Discharge (ESD) materials
• Removal/Replacement Instructions
If you are missing any part or any documentation, please call your designated service
representative.
Required Tools
You will need the following tools for removal/replacement procedures:
• T-10 and/or T-15 Torx drivers
• Light-duty flat-blade screwdriver with a 150mm (6-inch) blade
• Needle-nosed pliers
• ESD materials
Chapter 1 7
Getting Started
Safely Powering Down the B Class and C Class Workstation
Safely Powering Down the B Class and C Class Workstation
You must complete the following steps before performing any of the removal and
replacement procedures:
NOTE Remove any accessory bag(s) and their black tab screws, if present, from the
rear of the workstation.
1. Shut down the workstation by executing “shutdown -h” as user root. This ensures
that all programs are terminated and all data is saved before switching the power off.
Power down the workstation by simply pressing the power switch on the front panel.
Power off the monitor and any attached peripheral devices.
2. After 30 seconds, unplug the workstation’s power cord and all peripheral devices from
AC power outlets. Before attempting to move the workstation to a disassembly area,
disconnect all peripherals from the back of the system.
3. Place the workstation on a flat, stable surface, such as a tabletop or floor. To protect
against scratches, remove miscellaneous debris from the work surface.
8Chapter1
Getting Started
Product Exploded Diagram
Product Exploded Diagram
Refer to the figure below for a basic parts overview of the B Class and C Class workstation.
Figure 1-1. Exploded View
Chassis
Front-Panel Display
Hard Disk Tray
CD Drive Tray
Floppy Drive Tray
System Board
DIMMs (Memory)
Memory Fan
Side Panel
Power
System-Board Fans
I/O Fan/Speaker Bracket
Air Divider
I/O Card
Speaker
I/O Fan
Supply
Retainer Clip
9
2Parts Removal and Replacement
This chapter describes how to remove and replace the various parts in the B Class and C
Class workstations.
10 Chapter2
Parts Removal and Replacement
Terminators and Cables
Terminators and Cables
This section describes how to remove and replace the Terminators and Cables
Removing the Terminators and Cables
1. After powering down the workstation as described in the “Getting Started” chapter,
unplug the power cable from the back of the workstation. To avoid ESD damage to
components, carefully follow the ESD procedures (also described in the “Getting
Started” chapter).
2. Remove the two SCSI terminators from the back of the machine, as shown below. Or, if
you have already replaced either or both of the terminators with cables to external
peripheral devices, remove those cables., LAN cable, USB cables, and any other cables
from the back of the workstation.
Figure 2-1. Removing all Terminators and Cables
1. Remove the cables from the USB Clip from the back of the Workstation.
SCSI Terminators
Audio In/Out Ports
Parallel Port
LAN Port
USB Ports
Serial Ports
Power Plug
Other manuals for Visualize b1000
6
This manual suits for next models
2
Table of contents
Other HP Desktop manuals
HP
HP Xw6600 - Workstation - 2 GB RAM User instructions
HP
HP LaserJet 9000 Operator's manual
HP
HP Pavilion p6000 - Desktop PC User manual
HP
HP Compaq Presario Manual
HP
HP Pavilion 595 Installation instructions
HP
HP Compaq Pro 4300 Setup guide
HP
HP Compaq Presario Manual
HP
HP 633009-SK1 User manual
HP
HP Kayak XU800 Series User manual
HP
HP TouchSmart IQ530 Instruction manual
HP
HP ProDesk 600 G2 Small Form Factor Manual
HP
HP Compaq 6000 Pro SFF User manual
HP
HP st5742 - Streaming Client User manual
HP
HP Compaq Presario Specification sheet
HP
HP Xw4200 - Workstation - 1 GB RAM User manual
HP
HP Compaq Business Desktop dc7100 Series Assembly instructions
HP
HP Kayak XU 03xx Manual
HP
HP Pavilion a400 - Desktop PC User manual
HP
HP Slim Desktop S01 Assembly instructions
HP
HP Compaq Presario User manual
