Honeywell HEGS5300 User manual

MXMU000933 – July 2004 – Rev. A

HEGS5300

CCTV Control Keyboard

User Manual

Rev. A ii MXMU000933

07/07/04

ISSUE DATE REVISIONS

A July 2004 Initial Release (PCN 1752).

Rev. A iii MXMU000933

07/07/04

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER: This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at

his own expense.

CAUTION: Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: NOT FOR OUTDOOR USE UNLESS

ENCLOSED IN WATERPROOF HOUSING.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE

UNLESS ENCLOSED IN A WATERPROOF HOUSING.

Rev. A iv MXMU000933

07/07/04

NOTES:

Rev. A v MXMU000933

07/07/04

TABLE OF CONTENTS

SECTION 1: INTRODUCTION .................................................................................................................. 1

1.1 PRODUCT DESCRIPTION ............................................................................................................... 1

1.2 KEYBOARD OVERLAY..................................................................................................................... 1

1.3 ICONS .............................................................................................................................................. 2

SECTION 2: SETUP AND WIRING ........................................................................................................... 3

2.1 SETUP MODE .................................................................................................................................. 3

2.2 JOYSTICK ........................................................................................................................................ 4

2.3 KEYCODE TABLE ............................................................................................................................ 4

2.4 WIRING CONNECTIONS ................................................................................................................. 6

2.5 CABLE LENGTHS ............................................................................................................................ 6

Rev. A vi MXMU000933

07/07/04

NOTES:

Rev. A 1 MXMU000933

07/07/04

SECTION 1:

INTRODUCTION

1.1 PRODUCT DESCRIPTION

The HEGS5300 Keyboard interfaces to the HMXAT200 and supports all power

standards. The interface board in the HMXAT200 provides 12VDC at RJ11 connectors 3

and 4 (ports 3 and 4) to power a HEGS5300 keyboard. All keyboards connected to

other ports must have their own power supply. All HEGS5300 Keyboard models are

shipped with a universal power supply for 110 or 220VAC input to +12VDC output.

1.2 KEYBOARD OVERLAY

The illustration below is the standard default overlay on a HEGS5300 keyboard.

Overlays are exchangeable and can be customized so they may vary from site to site.

MAX1000 System Controller HEGS5300

S1 S2 S3 S4 S5 S6 S7 S8

POWER

COM

MAX

Rev. A 2 MXMU000933

07/07/04

1.3 ICONS

The following icons and their descriptions may or may not be on your specific controller.

Dome Macro

User Macro

Alarm Clear

Alarm Acknowledge

View / Preshot

Zoom In (tele)

Zoom Out (wide)

Focus Near

Focus Far

Iris Close

Iris Open

Dome / PTZ

Monitor

Camera

MAX

Maxpro Menu

Door Open

Clear

Aux

Video Recorder

Play

Reverse Play

Record

Stop

Pause

Frame Forward

Frame Back

Rewind

Fast Forward

Counter Reset

000

Counter Memory Stop

123

Time Mode

Time Date Search

Index Search

Scan Select

Insert camera into

scan

Delete camera from

scan

Lock Scan

Previous Step in

Scan

Next Step in Scan

Alternate Camera

Group

Night Shot

Auto Exposure

Dub

Review

Printer Select

Te x t

Function

Set

Select Monitor D

Select Monitor C

Select Monitor B

Select Monitor A

Last / Undo

Enter

Sequence

Live Record

4 x 4 Display

3 x 3 Display

2 x 2 Display

Picture in picture

Full Screen

Multiplexer Cursor

Multiplexer Zoom

Freeze

Multiplexer

Rev. A 3 MXMU000933

07/07/04

SECTION 2:

SETUP AND WIRING

2.1 SETUP MODE

HEGS5300 keyboards are setup using the keyboard keys.

There are three user-defined settings.

1. Keyboard ID – valid ID’s 1 to 99. (Default = ID 1).

2. Baud Rate – 19K2 or 9600.

(Default = 19K2. Data format is fixed at 7 data bits, 1 stop bit, even parity).

3. Joystick speed range – There are 2 ranges of pan/tilt speeds from the analog

joystick.

The default is a range of 5 speeds (0=STOP to 5=Maximum speed).

Speed 5 is generated when the joystick is at its maximum pan or tilt position.

The second range is from 0 to 26. As before, 0=STOP and the speeds

generated are from A (slowest) through Z (fastest). Speed Z is equivalent to

speed 5 in that it is generated when the joystick is at its maximum pan or tilt

position. This feature is available when using MAX1000, version 4.27 or later.

To enter the SETUP MODE hold down the MENU key

MAX

or the ©key (to the left-of

the LCD) as the keyboard is powered up.

NOTE: If the keyboard has a custom overlay, the MENU key may be located in a

different position. Therefore, the ©key next to the LCD is always the preferred

option.

In SETUP MODE, the LCD guides the user in entering required information using the

numeric keypad. Press the Enter key (↵)or the ªkey to the next screen.

Press the ©key to return to the previous setup screen.

When the keyboard ID, baud rate, and joystick speed range have been entered, the final

setup stage stores the settings and the joystick reference position. The keyboard should

be flat on the desk when pressing the enter key (↵) at this final stage to ensure the

joystick is zeroed. Setup information is stored in non-volatile memory so the settings will

be retained if the keyboard is unplugged.

Rev. A 4 MXMU000933

07/07/04

2.2 JOYSTICK

The HEGS5300 keyboard is equipped with a 3-dimensional joystick which allows

zoom-in and zoom-out functions to be performed by twisting the top of the joystick either

clockwise (zoom-in) or counterclockwise (zoom-out). The “ZOOM IN” and “ZOOM-OUT”

buttons located on the keyboard still operate as normal.

2.3 KEYCODE TABLE

Keycode Key Name Command Keycode Key Name Command

#001 ALARM ACK #026

#002 #027 Logical Group 9

#003 SCAN S #028 Logical Group 10

#004 HALT H #029 Logical Group 11

#005 PAUSE P #030 Logical Group 12

#006 #031 DOME MENU

#007 Logical Group 1 #032

#008 Logical Group 2 #033

#009 Logical Group 3 #034

#010 Logical Group 4 #035

#011 ALARM CLEAR A #036

#012 #037 Logical Group 13

#013 SCAN INSERT I #038 Logical Group 14

#014 SCAN DELETE D #039 Logical Group 15

#015 SET KEY T #040 Logical Group 16

#016 #041 MAX MENU ?

#017 Logical Group 5 #042

#018 Logical Group 6 #043 MULTIPLEXER Q

#019 Logical Group 7 #044 FULL SCREEN

#020 Logical Group 8 #045 MULTISCREEN

#021 USER MACRO U #046

#022 #047 VCR KEY R

#023 LEFT ARROW < #048 FUNCTION KEY

#024 LOCK KEY #049 UNDO

#025 RIGHT ARROW > #050 ALTERNATE

Table of contents

Other Honeywell Security Camera manuals

Honeywell

Honeywell IPCAM-WOC1 User manual

Honeywell

Honeywell HB73SPX User manual

Honeywell

Honeywell HEIPTZ-2201W-IR User manual

Honeywell

Honeywell Performance HQA HD72HD4 Series User manual

Honeywell

Honeywell EQUIP Series User manual

Honeywell

Honeywell HD251 User manual

Honeywell

Honeywell HSGN502 User manual

Honeywell

Honeywell 30 Series User manual

Honeywell

Honeywell HC60WZ2E30 User manual

Honeywell

Honeywell HCCM474M User manual

Honeywell

Honeywell HDZ402LIWV User manual

Honeywell

Honeywell KD6A User manual

Honeywell

Honeywell HEIPTZ-2736-WI User manual

Honeywell

Honeywell HC60WB4R2 User manual

Honeywell

Honeywell HD3CHS User manual

Honeywell

Honeywell ACUIX ES Operator's manual

Honeywell

Honeywell HB75 User manual

Honeywell

Honeywell HZC-755N/P Series User manual

Honeywell

Honeywell HD73P Series User manual

Honeywell

Honeywell HD60 Series User manual

Honeywell

Honeywell HD3CH User manual

Honeywell

Honeywell HDZ20HD User manual

Honeywell

Honeywell HCC10 User manual

Honeywell

Honeywell HD3DSX User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications