Honeywell Stryker VAV User manual

OPERATING GUIDE

Put Bar Code Here

63-2730-01

Stryker VAV Zio Configuration

TABLE OF CONTENTS

Zio Configuration Scope ..................................................................................................................................2

Home Screen Options ..................................................................................................................................2

Tenant View More ..................................................................................................................................3

Contractor View - Parameter Groups ..................................................................................................................................3

Sensors ..................................................................................................................................7

Equipment Status ..................................................................................................................................9

Temperature Setpoints ..................................................................................................................................10

Override ..................................................................................................................................12

Alarms ..................................................................................................................................13

Airflow Balance ..................................................................................................................................14

Air Flow Configuration ..................................................................................................................................16

Airflow Setpoints ..................................................................................................................................16

Damper Configuration ..................................................................................................................................17

Sensor Calibration ..................................................................................................................................18

Wall Module Configuration ..................................................................................................................................19

Control Configuration ..................................................................................................................................22

Configure Universal Inputs ..................................................................................................................................24

Configure Sbus ..................................................................................................................................25

Configure Logical Inputs ..................................................................................................................................25

Configure Floating Ouput1 ..................................................................................................................................26

Configure Analog Output 1 & 2 ..................................................................................................................................27

Configure Logical Outputs ..................................................................................................................................28

Standard Zio Configuration Functions ..................................................................................................................................31

STRYKER VAV ZIO CONFIGURATION

63-2730—01 2

ZIO CONFIGURATION SCOPE

This document serves as a technical users guide for an

installer who is configuring a Stryker VAV controller via a

TR71 or TR75 wall module. Parameters are grouped into

logical categories rather than on large list. To access the

“Contractor” mode for configuration, press the Up, Down and

middle keys simultaneously. During this time the model

number and firmware revision of the TR71/75 will be displayed

and then you will be prompted to enter a password (default

0000) to enter the Contractor mode. You can then navigate to

the desired category of parameters and then begin

configuring and viewing information from the device. Each

screen below has a brief explanation of the data, and in cases

where the data can be changed, the corresponding network

variable is shown in brackets. For example, the “MAX FLOW”

parameter that is found in the “BALANCE” category is

manipulating the MaxMeasFlowAct section of the

nciBalanceSetPts structured nci and is noted as

[nciBalanceSetPts, MaxMeasFlowAct]. Values within the

Contractor mode are only viewable in English (U.S.) units of

measure. Temperatures however CAN be shown on the home

screen as C or F.

Controller Features NOT Supported by Zio Configuration

• Network Functionality

• Accessory Loops

• Custom Sensors

• Local Sensor (UI 1-4) Calibration

VAV Controller Default Configuration

Wall Module = Zio

Center SetPoint Source: Zio

Center SetPoint: Disabled (controller ignores center setpoint

value)

Center SetPoint High Limit: 100

Center SetPoint Low Limit: -10

Room Temperature Source = Zio (TR71/75)

Pressure independent flow control

Temperature Control = Cooling Only

Floating Damper Motor:

Connected to DO3 & DO4

90 sec travel time

HOME SCREEN OPTIONS

Center SetPoint, Outside Air & Room Temperature (setpoint is

adjustable from Home Screen)

Room, Outside Air Temperature & Center SetPoint (setpoint is

adjustable from Home Screen)

Center SetPoint Temp (setpoint is adjustable from Home

Screen)

STRYKER VAV ZIO CONFIGURATION

363-2730—01

Center SetPoint & Room Temperature (setpoint is adjustable

from Home Screen)

Default Home Screen. Room Temperature & Center SetPoint

(setpoint is adjustable from Home Screen)

Room Temperature (setpoint is NOT adjustable from Home

Screen)

TENANT VIEW MORE

NOTE: To add or remove items from the Tenant View

More sequence use Contractor Mode by holding

the up, down and center buttons for 5 seconds.

During this time the display will show the model,

firmware version and Sylk bus address of the

TR71/75. Select “SetViewMore” to add or remove

items by choosing “YES” or “NO” with the up/

down buttons.

Center Setpoint Temperature

NOTES:

1. The center setpoint can be disabled using Con-

tractor View: WM_CONFG, CNTR_SP, FALS or

true.

2. If CNTR_SP = FALS, the set point can be

changed, however the value is ignored.

3. The range can be controlled by WM_CONFG:

CNTSP_HI, & CNTSP_LO

4. To remove the CNTR_SP from the View More

screen use Contractor Mode: SetViewMore, SET-

POINT = NO

CONTRACTOR VIEW -

PARAMETER GROUPS

View sensor parameters

STRYKER VAV ZIO CONFIGURATION

63-2730—01 4

View equipment status data

Edit Temperature Setpoints

Set overrides for the controller

View alarm conditions

Edit balancing parameters

Edit Flow Configuration parameters

Edit Flow Setpoints

STRYKER VAV ZIO CONFIGURATION

563-2730—01

Damper Config for pressure dependent control

Calibration of dP, Zio and C7400S sensors

Wall module configuration

Configuration of control parameters

Universal input configuration

Configure C7400S sensor

Configure logical inputs

Configure floating output 1

STRYKER VAV ZIO CONFIGURATION

63-2730—01 6

Configure floating output 2

Configure analog output 1

Configure analog output 2

Configure logical outputs

View controller time

Set controller time

Set controller date

Set controller schedule

STRYKER VAV ZIO CONFIGURATION

763-2730—01

SENSORS

Parameter Group Name

View Zio temperature

View Zio relative humidity

View room temperature

View room RH

View room CO2

View supply air temperature

STRYKER VAV ZIO CONFIGURATION

63-2730—01 8

View discharge air temperature

View outdoor air temperature

View box airflow (cfm only)

View Flow Pressure un-calibrated in Pascals

View calibrated pressure (inWC only)

View Occ Sensor status

View Window switch

STRYKER VAV ZIO CONFIGURATION

963-2730—01

EQUIPMENT STATUS

Parameter Group Name

View damper position

View airflow setpoint

View reheat valve position

View number of reheat stages on

View periph heat valve position

View number of periph stages on

STRYKER VAV ZIO CONFIGURATION

63-2730—01 10

View demand limit setpoint shift

View auxiliary output status

View fan status

View modulating fan status

TEMPERATURE SETPOINTS

Parameter Group Name

Set occupied cooling setpoint [nciTempSetpoints,

occupiedCool]

Set occupied heating setpoint [nciTempSetpoints,

occupiedHeat]

Table of contents

Other Honeywell Controllers manuals

Honeywell

Honeywell 190797-YAD User manual

Honeywell

Honeywell Tema-Voyager Multi VMC Series User manual

Honeywell

Honeywell V4055F Operation manual

Honeywell

Honeywell GENT Mimic LED Driver Card Instruction manual

Honeywell

Honeywell HON 5020 User manual

Honeywell

Honeywell S9360B User manual

Honeywell

Honeywell CENTRA LINE EAGLEHAWK Installation and operation manual

Honeywell

Honeywell UDC1200 MICRO-PRO User manual

Honeywell

Honeywell W7752D2007 User manual

Honeywell

Honeywell Lyric User manual

Honeywell

Honeywell Pressuretrol L404 Series User manual

Honeywell

Honeywell CN34 Series Operation manual

Honeywell

Honeywell Spyder PUB6438S User manual

Honeywell

Honeywell 023350.17 Instruction manual

Honeywell

Honeywell FR124 User manual

Honeywell

Honeywell UDC1200 MICRO-PRO User guide

Honeywell

Honeywell ESYS S4965A3025 Operating and installation instructions

Honeywell

Honeywell HR 40 F User manual

Honeywell

Honeywell DKG 972 User manual

Honeywell

Honeywell UDC3300 User manual

Honeywell

Honeywell UDC3300 User manual

Honeywell

Honeywell Excel 10 W7752D User manual

Honeywell

Honeywell TBC2800 Series User manual

Honeywell

Honeywell CVL4022ASVAV1 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual