Honeywell LT-32 User manual

Fire Alarm Control Panel LT

-32 / LT-159

Quick Start Guide

-168.2-EN / 07.2022

Honeywell

MORLEY IAS Fire Systems

Support@honeywell.com

www.honeywell.com

Technical changes reserved!

Morley LT-32 Morley LT-159 Panel Installation - Three Steps Process Cable Entries Field Cable Entry

STEP 1

According to the figure, mark

the required hole on the wall.

STEP 2

All fixing point must be used.

Use 50 mm long x 5 mm diameter

screws to secure the backbox on the

wall.

•Upper and lower cable entry for 15 mm gland

•Side entry: 3 on each side (21 x 21 mm easy access)

•Central entry prepared for 60 mm universal flush box

Remove the keyholes and pass

the cables through them.

Power supply and batteries are required for commissioning!

STEP 3

Align the screws on the cover with the keyhole on the back box and lock

the cover onto the backbox.

System Setup and Cabling

Alarm and Fault Relay

Move the Jumper to Setup NO or

NC relay functionality.

Sounder circuit

End of line diode cathode marker on

positive terminal.

LT-32 Ref. Description LT-159 Ref. Description

1Fault NO/NC

Fault C

Alarm NO/NC

4Alarm C 4Alarm C

Loop A +

Loop A -

7Sounder 2 + 7Loop B +

Sounder 2 -

Loop B -

Sounder 1 +

10 Sounder 1 -10 Sounder 1 -

11 Power + 11

Power +

Power -

Panel Connection

Highlighted the differences between panel LT-32 and LT-159.

Battery Connection

Batteries connected in two rows 

with polarity as shown.

Additional and updated Informations

The described features, specifications and product related informations in this manual correspond to the date of issue (refer to date on the front page) and may differ due to modifications and/or amended Standards and

Regulations of the System design, Installation and Commissioning.

For further Informations refer to documentation M-168.1-SERIE-LT-EN.

Panels Display Controls, Buttons and Password Quick Programming Procedure with Default General Alarm Functionality

STATUS ICON

CONDITION /

CONTROL

COLOR DESCRIPTION

FIRE

Red (blinking)

A fire condition has been detected (buzzer active)

Red (fixed)

The user has acknowledged the event by buzzer silence

SYSTEM FAULT Yellow (fixed) System fault

GENERAL FAULT

Yellow (blinking)

General fault, buzzer is active

Yellow (fixed) The user has acknowledged the event by buzzer silence

DISABLE Yellow (blinking) A device or zone is disabled

TEST Yellow (blinking) A zone is in test mode

SOUNDER SILENCE

Yellow (blinking)

The internal buzzer is silenced

Yellow (fixed)

The sounders are silenced

POWER FAULT

(from 100 … 230 Vac

or batteries)

Yellow (blinking)

Mains fault

Yellow (fixed) Batteries fault

POWER Green (fixed) The system is switched on and the power is supplied via the mains

1. On the touch screen display press the arrow on the right and then press the gear icon at the top right:

2. Insert password level 2, press enter then press on program icon, insert password level 3 and press enter to confirm.

3. Select Panel configuration to change the language using the arrow down icon.

Once completed, press the left arrow to come back to the previous screen.

4. Select Autoprog, press the Lens icon to search for devices, at the end of the process save devices detected with

check mark. Press the left arrow to come back to the previous screen.

5. Select Description to change both Zone and Point labels. This example refers to Zones: Press Zone icon, type the

label using the virtual keyboard and confirm with enter. Same applies to Points.

6. Come back to Configuration menu using the left arrow and set Date and Time. The example shares how to change

Date: select Date icon, scroll up and down the day, month and year values then confirm with check mark. To change

Time, follow the same process.

PUSH

BUTTON

DESCRIPTION FUNCTION

RESET PANEL Pressing the ‘Reset Panel’ button will reset the panel to return it to normal condition after an event

MUTE Pressing the ‘Mute’ button or tapping on the touch screen, will silence the active panel buzzer

SILENCE SOUNDERS Pressing the ‘Silence Sounders’ button will silence all Alarm sounders

EVACUATE

Pressing the ‘Evacuate’ button and later confirm the evacuation in the pop-up window, will start

all the panel sounders output activation and the output configured for evacuation in the Cause

and Effect I/O Matrix

FUNCTION

EN 54 LEVEL

FACTORY DEFAULT PASSWORD

Alarm, disabled, and faults display

Level 1

None

Alarm and faults recognition

Level 1

None

Disabled Zone/Point display

Level 1

None

Enable/Disable menu

Level 2

2222

Test menu

Level 2

2222

Utility menu

Level 2

2222

Programming menu

Level 3

33333333

Other manuals for LT-32

This manual suits for next models

Other Honeywell Controllers manuals

Honeywell

Honeywell DCP301 User manual

Honeywell

Honeywell MS4104F1010 User manual

Honeywell

Honeywell UMC800 User manual

Honeywell

Honeywell ATC928G3000 User manual

Honeywell

Honeywell WEB-600E User manual

Honeywell

Honeywell HW-AV-LTE-M User manual

Honeywell

Honeywell HercuLine 10260A User manual

Honeywell

Honeywell Excel 10 W7751H User manual

Honeywell

Honeywell VC6613AJ1000 User manual

Honeywell

Honeywell J48 User manual

Honeywell

Honeywell SHC Series User manual

Honeywell

Honeywell M6410A User manual

Honeywell

Honeywell HON 670 Guide

Honeywell

Honeywell HC900 Operating manual

Honeywell

Honeywell UMC800 User manual

Honeywell

Honeywell UDC2500 User manual

Honeywell

Honeywell UDC 2300 User manual

Honeywell

Honeywell Zio TR70 User manual

Honeywell

Honeywell L482A User manual

Honeywell

Honeywell N20 Series Operation manual

Honeywell

Honeywell HVC0001 User manual

Honeywell

Honeywell MP909E Datasheet

Honeywell

Honeywell CLMEVA00IB24NM User manual

Honeywell

Honeywell HC900 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual