Honeywell HCE 40 Programming manual

Storey

Controller

HCE 40

Installation and Operation

Contents

Overview 3

Application 3

Installation procedure 4

Creating zoning plan 4

Installing 4

Configuring and making electrical connections 4

Start-up 4

Creating zoning plan 5

Determining temperature zones 5

Filling out zoning plan 6

Installation 10

Wall installation 11

Installation on DIN rails 12

Installing storey controller components 12

Description 13

Layout of circuit board 13

LED indicators on storey controller 14

Operating modes of storey controller 15

Buttons on storey controller 17

Configuration and electrical connection 19

Opening housing 19

Branching out time programs 20

Contents

Setting actuator 22

Switching between heating/cooling 23

Cabling connections 24

Start-up 35

Starting up storey controller 35

Start-up with central operating device 36

Assigning setpoint adjusters of type HCU 23 or HCW 23

to a zone 40

Removing assignment 40

Saving settings at central operating device 43

Checking installation 43

Completing start-up 44

Resetting storey controller to state of delivery 45

Appendix 46

Glossary 46

Help with problems 47

Overview of heating components 50

Zoning plan 51

Overview

For your information

Technical terms are explained in the glossary (Page 46). They are

identified in the text by an *.

Application

The storey controller HCE 40 receives information on the temperature

of the room from the setpoint adjusters*, room temperature sensors of

type RF 20 or from the central operating device* HCM 100. The storey

controller uses this information to control the boiler feedback*, the

pump relay and the thermal actuators* (see "Overview of heating

components" Page 50).

The storey controller HCE 40 is hard-wired to setpoint adjusters of

type HCU 23 or HCW 23, room temperature sensors of type RF 20 or

the central operating device HCM 100.

It has a self-learning controller (fuzzy logic), which automatically

adjusts the control parameter according the installation conditions.

The desired room temperature is reached quickly and then

maintained.

Overview

Installation procedure

Creating zoning plan

• Determining which heating circuits* are controlled by the storey

controller.

Installing

• Installing the components of the storey controller HCE 40.

Configuring and making electrical connections

• Setting the storey controller to the actuator type, attaching cables to

the respective connections and connect components together.

Start-up

• Assigning room names to the temperature-zones with the central

operating device HCM 100 if applicable.

Creating zoning plan

A temperature zone is an area of the building, e.g. a room, in which

the setpoint temperature* is set with a setpoint adjuster. The storey

controller controls all thermal actuators of a temperature zone

identically.

5 temperature zones can be set up for each storey controller.

3 actuators can be connected in each of 3 zones, and 2 actuators can

be connected in each of the remaining 2 zones.

The total number of actuators which can be controlled by a signal

storey controller is limited to 10.

Determining temperature zones

Caution!

Damage caused by equipment from other manu-

facturers!

The storey controller was designed for use with

components from Honeywell only!

►Use only H 200 AG (normally closed) or H 200 AO

(normally open)-type actuators.

►Group actuators (by type and location) which are controlled with the

storey controller.

►Group together all actuators which are controlled by a setpoint

adjuster in a temperature zone.

Creating zoning plan

If more than 5 temperature zones or 10 actuators are present:

►Determine the number of additional storey controllers required using

the following table:

Temperature

zones (maximum)

Actuators

(maximum)

No. of storey

controller

5 10 1

10 20 2

15 30 3

Hint: The example at the end of this section shows zone divisions with

corresponding zoning plan.

Filling out zoning plan

►Copy the sample zoning plan ("Zoning plan" Page 51) (archive it).

►Enter the type and installation location of the respective actuator in

each temperature zone.

►Assign a setpoint adjuster or room temperature sensor to each

temperature zone.

►Assign room names if necessary.

►Hand over the zoning plan to the customer after installation.

Creating zoning plan

Example of zone divisions

Living Dining

Bathroom WC

Bedroom

Kitchen

Hall

Zone 1 Zone 2 Zone 5

Zone 3 Zone 4

This example shows:

• A home divided into five temperature zones.

• Bathroom and WC are controlled by one setpoint adjuster. One

temperature zone is sufficient for three actuators.

• The maximum number of actuators (10 per storey controller) is used

to the full with the storey controller.

Creating zoning plan

The example yields the following zoning plan:

Temper-

ature zone

Actuator

(type, location)

Setpoint

adjuster

(location)

Room name

at operating

device

Heating loop 1

(living room)

Living room "Living"

Zone 1 Heating loop 2

(living room)

Heating loop 1 (dining

room)

Dining room "Dining"

Zone 2 Heating loop 2 (dining

room)

Heating loop 1 (bathroom) "Bathroom/

WC"

Heating loop 2 (bathroom)

Zone 3

Heating loop 3 (WC)

Bathroom and

Heating loop 1 (bedroom) Bedroom "Bedroom"

Zone 4

Heating loop 2 (bedroom)

Zone 5 Heating loop 1 (kitchen) Kitchen "Kitchen"

Table of contents

Other Honeywell Controllers manuals

Honeywell

Honeywell AQUASTATIC L7224 Series User manual

Honeywell

Honeywell WEB/CP-202-XPR User manual

Honeywell

Honeywell L482A User manual

Honeywell

Honeywell EDC 200 Series User manual

Honeywell

Honeywell UMC800 User manual

Honeywell

Honeywell MSR PolyGard 2 MGC2-K User manual

Honeywell

Honeywell SILENT KNIGHT SK-Control Manual

Honeywell

Honeywell UltraKey Touch HJC4000 User manual

Honeywell

Honeywell ML7425A Series Operation manual

Honeywell

Honeywell ComfortPoint Open CPO-VAV2A User manual

Honeywell

Honeywell MT8-024 User guide

Honeywell

Honeywell PCR-310 User manual

Honeywell

Honeywell S05 Series Operation manual

Honeywell

Honeywell M847D User manual

Honeywell

Honeywell NOTIFIER NFXI-RM6 User manual

Honeywell

Honeywell touchpoint Pro User manual

Honeywell

Honeywell T2798I2000 User manual

Honeywell

Honeywell ADEMCO Optiflex User manual

Honeywell

Honeywell Ultrakey Lite User manual

Honeywell

Honeywell EVOTOUCH CONTROLLER User manual

Honeywell

Honeywell R7184A User manual

Honeywell

Honeywell VC6613ME6000 User manual

Honeywell

Honeywell Novar ES3.S Programming manual

Honeywell

Honeywell CentraLine EAGLEHAWK NX User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual