Honeywell Notifier FMM-1 User manual

MOUNTING

The FMM-1 mounts directly to 4-inch square electrical boxes (see Figure 2).

The box must have a minimum depth of 21⁄8inches. Surface mounted electri-

cal boxes (SMB500) are available from Notifier.

FIGURE 2. MODULE MOUNTING:

NOTE: For UL Listed security installations, the FMM-1 must be mounted

within the control panel enclosure.

ISOLATED

QUADRANT

C1066-00

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and

regulations. This module is intended for power limited wiring only.

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in

Figure 2.

SPECIFICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 5.0 mA (LED on)

Average Operating Current: 375 µA (group poll); 350 µA (direct poll); 600 µA Max. (Communicating, IDC Shorted)

EOL Resistance: 47K Ohms

Maximum IDC Wiring Resistance: 1,500 Ohms

Maximum IDC Voltage: 11 Volts

Maximum IDC Current: 450µA

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Dimensions: 41⁄2˝ H x 4˝ W x 1

1⁄4˝ D (Mounts to a 4˝ square by 21⁄8˝ deep box.)

Accessories: SMB500 Electrical Box

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the control panel installation manual for detailed system information. If the

modules will be installed in an existing operational system, inform the opera-

tor and local authority that the system will be temporarily out of service. Dis-

connect power to the control panel before installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The FMM-1 Monitor Module is intended for use in intelligent, two-wire sys-

tems, where the individual address of each module is selected using the built-

in rotary switches. It provides either a 2-wire or 4-wire fault tolerant initiating

device circuit (IDC) for normally open contact fire alarm and supervisory de-

vices, or either normally open or normally closed security devices. The mod-

ule has a panel controlled LED indicator. The FMM-1 can be used to replace

an MMX-1 module in existing systems. FMM-1 is also UL Listed as a com-

mercial proprietary burglar alarm accessory and a commercial central station

burglar alarm accessory.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Notifier system control panel (list available from Notifier).

FIGURE 1. CONTROLS AND INDICATORS:

C1067-00

NO-460-010 1 I56-3506-001

FMM-1 Monitor Module

I56-3506-001

INSTALLATION AND MAINTENANCE INSTRUCTIONS

12 Clintonville Road

Northford, CT 06472-1653

Phone: 203.484.7161

FIGURE 3. TYPICAL 2-WIRE INITIATING CIRCUIT CONFIGURATION, NFPA STYLE B OR SECURITY SYSTEMS:

NOTE: For UL Listed security installations, the FMM-1 must be mounted within the control panel enclosure.

(+)

(–)

(+)

(–)

(+)

(–)

MONITOR

MODULE

ANY NUMBER OF UL LISTED CONTACT

CLOSURE DEVICES MAY BE USED. DO NOT MIX

FIRE ALARM INTIATING, SUPERVISORY, OR

SECURITY DEVICES ON THE SAME MODULE.

TO NEXT

DEVICE

FROM PANEL OR

PREVIOUS DEVICE

47K EOL

RESISTOR

ELR-47K

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

INITIATING DEVICE CIRCUIT (IDC) - NFPA STYLE B

POWER LIMITED: 450µA MAX. @ 11 VDC MAX

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

C0918-00

FIGURE 4. TYPICAL 4-WIRE FAULT TOLERANT INITIATING CIRCUIT CONFIGURATION, NFPA STYLE D:

(+)

(-)

(+)

(–)

(+)

(–)

TO NEXT

DEVICE

ANY NUMBER OF UL LISTED CONTACT

CLOSURE DEVICES MAY BE USED. DO NOT MIX

FIRE ALARM INTIATING, SUPERVISORY, OR

SECURITY DEVICES ON THE SAME MODULE.

MONITOR

MODULE

FROM PANEL OR

PREVIOUS DEVICE

CONNECT MODULES TO LISTED COMPATIBLE

CONTROL PANELS ONLY

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMENDED

ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED

INSTALL CONTACT CLOSURE DEVICES PER

MANUFACTURER’S INSTALLATION INSTRUCTIONS.

EOL RESISTOR IS

INTERNAL AT

TERMINALS 8 & 9

C0919-02

NO-460-010 2 I56-3506-001

Other Honeywell Control Unit manuals

Honeywell

Honeywell NOTIFIER XP6-MA User manual

Honeywell

Honeywell PFA 700 Manual

Honeywell

Honeywell Maxon SMA11 User manual

Honeywell

Honeywell SM150 User manual

Honeywell

Honeywell PRO4200 User manual

Honeywell

Honeywell VR4300 User manual

Honeywell

Honeywell FALCON MJ Pulse/M-Bus User manual

Honeywell

Honeywell Maxon SMA11 User manual

Honeywell

Honeywell Class 500 User manual

Honeywell

Honeywell W6215 Series Operation manual

Honeywell

Honeywell Braukmann BV300 User manual

Honeywell

Honeywell RV284 User manual

Honeywell

Honeywell IntelliDoX User manual

Honeywell

Honeywell VC7900 Series Operation manual

Honeywell

Honeywell PS300 User manual

Honeywell

Honeywell LTE-L57A User manual

Honeywell

Honeywell SUPER TRADELINE S8610U User manual

Honeywell

Honeywell DR 300 User manual

Honeywell

Honeywell BSM Assembly instructions

Honeywell

Honeywell D05T User manual

Honeywell

Honeywell Braukmann T100A Operation manual

Honeywell

Honeywell ERM5220R1018 User manual

Honeywell

Honeywell VR8215S User manual

Honeywell

Honeywell VGF21 Operation manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual