Honeywell BSM Assembly instructions

K14864V3 9/10 Rev. A

BSM

Battery Sense Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The Honeywell Battery Sense Module is a control panel

accessory that is used to monitor and report the backup

battery status. Its features are:

Monitors and reports for one or two batteries.

Detects and reports low battery conditions.

Detects and reports if a battery is removed.

Provides deep discharge battery protection if AC

power is lost and the backup battery voltage falls

below a safety threshold of 9.5 to 10 volts.

Additional modules can be used for those control panels

that use additional batteries.

PACKAGE CONTENTS

The following items are included:

Battery Sense Module with bracket

Battery Harness (qty 2)

Summary of Connections label

SPECIFICATIONS

Physical: 3-1/8” L x 2-3/4” W x 3/4” H

(80mm x 70mm x 20mm)

Electrical:

Input Voltage: 12VDC nominal (from control panel)

Input Current: 20mA (max used by BSM)

Current Handling Capability: 2.3A maximum

(Control panel load must not exceed 2.3A.)

INSTALLATION

1. Select a suitable area in the control panel where

the mounting will not interfere with testing or

servicing of other components.

2. Clip the Battery Sense Module to the cabinet edge.

CONNECTIONS

1. Refer to the Connections Diagram on other side.

When connecting leads, support the module to

prevent stress on the circuit board.

2. Connect the module's power leads to the control

panel's 12VDC backup battery power terminals.

3. Connect backup battery A to the module. Then

connect backup battery B (if present) to the module.

4. If only one backup battery is being used, depress

the ENROLLMENT switch to toggle the Battery

Sense Module to sense only one battery.

ULC

When used with one battery and the total

load is greater than 1.5A, jumper the

Battery A terminals and the Battery B

terminals on the Battery Sense Module to

the backup battery.

5. For non-Honeywell control panels, connect the

ZONE OUT to an unused control panel zone. (Do

not use a fire zone.)

Note: For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT terminal on

the BSM. The Honeywell control panel will

automatically detect a low or missing battery

through the panel's battery cable.

6. Affix the supplied Summary of Connections label to

the inside of the control panel.

CONFIGURATION

1. Refer to the control panel's installation guide for

details on fault monitoring.

2. For non-Honeywell control panels, program the

connected zone for the Battery Sense Module to

detect an active high fault condition.

ZONE OUT

BAT

BSM-001-V0

B AT. A PANEL

B AT. B

DOCUMENTATION AND ONLINE SUPPORT

For the latest documentation and online support information, please go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14864V3cŠ

K14864V3 9/10 Rev. A

STATUS LEDs (A and B)

STEADY ON Battery is present and good.

BLINKING Battery is programmed to be

present, and is NOT present.

OFF Battery is NOT programmed to be

present.

ENROLLMENT Switch

Default condition is for 2

batteries.

Depress once for 1 battery.

To the control panel battery terminals.

To Battery A terminals.

To Battery B terminals.

To a non-Honeywell

control panel zone for

fault monitorin

Note:

For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT ter-

minal on the BSM. The Honeywell

control panel will automatically detect

a low or missing battery through the

panel's battery cable.

Other Honeywell Control Unit manuals

Honeywell

Honeywell JADE W7220 User manual

Honeywell

Honeywell Esser 8044 Series User manual

Honeywell

Honeywell V5825B User manual

Honeywell

Honeywell SK-Mon-10 User manual

Honeywell

Honeywell RMG 213 Guide

Honeywell

Honeywell VRN Series User manual

Honeywell

Honeywell RV283P User manual

Honeywell

Honeywell Braukmann D05 User manual

Honeywell

Honeywell Galaxy 2 Series User manual

Honeywell

Honeywell LTE-L57V User manual

Honeywell

Honeywell AlarmNet 7847i-E Assembly instructions

Honeywell

Honeywell TR80UWD Installation guide

Honeywell

Honeywell Notifier NRX-M711 User manual

Honeywell

Honeywell RV280 User manual

Honeywell

Honeywell BCU 460 Manual

Honeywell

Honeywell S8921D User manual

Honeywell

Honeywell ADEMCO 5800RL Assembly instructions

Honeywell

Honeywell C7110C1040 User manual

Honeywell

Honeywell VQ400 Series User manual

Honeywell

Honeywell DIAL-SET DS05C Operation manual

Honeywell

Honeywell TR80 Installation guide

Honeywell

Honeywell MCV2000AA Installation instructions

Honeywell

Honeywell V5013N Operation manual

Honeywell

Honeywell 7800 SERIES User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual