Honeywell L506 User manual

www.inncom.com 1

L506 Wireless Lamp Control

Module Installation Guide

The L506 FET

dimmer can drive

dimmable CFL

loads and other

loads:

•100W

Incandescent

•35W Dimmable CFL or 100W

incandescent equivalent

•25W LED or 100W

incandescent equivalent

As an alternative to the L206 lamp

socket module, the L506 provides

wireless lamp control with a smaller

footprint. Designed for standard

medium lamp sockets (E26 Edison),

the RF-equipped device can be

controlled from any INNCOM IRAS

device with an RF transceiver. The

socket is equipped with a mechanical

button that can control the load and

assist in device binding. The L506

series will eventually incorporate

sibling products designed for other

lamp socket types.

Installation

The installer must be a trained,

experienced service technician.

When installing this product:

1. Read the instructions carefully.

Failure to follow them could

damage the product or cause

hazardous conditions.

2. Check the ratings given in the

product guide to make sure the

product is suitable for your

application..

3. Use the L506 module

only with a recognized

or listed lamp holder

assembly.

CAUTION: The distance

between the bulb and the

shade should be equal to or

greater than required by the original

UL listing for the lamp base.

Improper placement is a fire hazard.

Mounting

The L506 may be mounted in

vertical/bulb up, horizontal, or

vertical/bulb down fixtures.

CAUTION:

The bulb-down orientation should

generally be confined to open air

installations; if used with a shade, the

fixture should be further derated (see

table below).

1. If the lamp’s Edison socket has a

switch, make sure it is in the full

on position, then remove or

disable it.

2. The L506 dimmer-equipped lamp

must be within 60 feet (indoors) of

an RF transceiver/repeater.

3. Unplug the lamp cord from the

power source (e.g., wall socket).

4. Remove any shade and lamp

harp.

5. Remove the bulb; screw the L506

dimmer/switch into the lamp

socket.

6. Reinstall the bulb, then the lamp

harp (if used). Rotate the harp if

necessary to clear the L506

socket. Plug the lamp back into

the power supply.

Derating: Do not exceed an ambient

air temperature of 25˚C surrounding

the L506 Lamp Controller when

operating the lamp with the specified

loads and orientations, as outlined in

the following table.

Maximum Ratings

Vertical

Base Down

(bulb up) or

Horizontal

Vertical

Base Up

(bulb

down)*

Incandescent 100W 60W

Dimmable

CFL 35W 20W

LED 25W 10W

*Open air only. If fixture enclosed, further

derating is necessary

Communications

The L506 can switch on a light using

the built-in on/off button. For remote

and dimming operation, the L506

must be located within 60 ft. of an

originating RF transmitter (any IRAS

RF device can be configured as a

repeater). The L506 must be

commissioned. The outline below

assumes the installer understands

the commissioning process in

general; specific commissioning

procedures can be found on the

property-specific commissioning

sheet.

Commissioning

The L506 must be bound to an RF

control device such as an e528

thermostat.

1. The L506 enters bind mode for the

first 2 minutes after powering up;

www.inncom.com 2

to re-enter bind mode, unscrew

the L506 from the fixture and then

screw it back in.

2. On the e528, enter the Service

menu.

•Press and hold the F°/C°

button

•Press and release

OFF/AUTO

•Press and release DISPLAY

•Release F°/C°

3. Use the UP or DOWN arrows to

go to the Address parameter

(ADR).

4. Press DISPLAY. Use the

UP/DOWN arrows to enter the

ADR value from the

commissioning sheet.

5. Press OFF/AUTO; a single beep

should sound.

6. On the L506, press and hold the

built-in on/off button for 5 seconds.

The e528 will beep quickly 3 times

to confirm binding.

Operation

Besides being used in the binding

operation, the built-in button on the

L506 can control the lighting load.

Press and hold the button to adjust

lighting (dimming) levels up or down. A

quick press will turn the light off or on.

The L506 has a status indicator LED.

When the lamp is on, the LED is too.

Technical Specifications

Parameter Rating

Power 110-120VAC, 50/60Hz

0.9A dimmable output

Standby power

Standby current

1.3W

11mA

Operating

Environment

0–25 C˚

Parameter Rating

Dimensions: 63.3mm L × 47.3mm

W x 98mm H (with

socket)

Approvals FCC Part 15b, Class

A, UL

FCC ID: GTC202516TXR

This device complies with part 15 of

the FCC R les. Operation is s bject

to the following two conditions: (1)

This device may not ca se harmf l

interference, and (2) this device m st

accept any interference received,

incl ding interference that may

ca se ndesired operation.

This eq ipment has been tested and

fo nd to comply with the limits for a

Class B digital device, p rs ant to

Part 15 of the FCC R les. These

limits are designed to provide

reasonable protection against

harmf l interference in a residential

installation. This eq ipment

generates, ses, and can radiate

radio freq ency energy and, if not

installed and sed in accordance with

the instr ctions, may ca se harmf l

interference to radio

comm nications. However, there is

no g arantee that interference will

not occ r in a partic lar installation.

this eq ipment does ca se harmf l

interference to radio or television

reception, which can be determined

by t rning the eq ipment off and on,

the ser is enco raged to try to

correct the interference by one of the

following meas res:

—Reorient or relocate the receiving

antenna.

—Increase the separation between

the eq ipment and receiver.

—Connect the eq ipment into an

o tlet on a circ it different from that

to which the receiver is connected.

—Cons lt the dealer or an

experienced radio/TV technician for

help.

Any changes or modifications not

expressly approved by the party

responsible for compliance co ld

void the ser's a thority to operate

this eq ipment.

C ID: 1609A-202516TXR

This device complies with Ind stry

Canada license-exempt RSS

standard(s). Operation is s bject to

the following two conditions: (1) this

device may not ca se interference,

and (2) this device m st accept any

interference, incl ding interference

that may ca se ndesired operation

of the device.

Le présent appareil est conforme a x

www.inncom.com 3

CNR d’ind strie Canada applicables

a x appareils radio exempts de

licence. L’exploitation est a torisée

a x de x conditions s ivantes: (1)

l’appareil ne doit pas prod ire de

bro illage, et (2) l’ tilisate r de

l’appareil doit accepter to t

bro illage

radioélectriq e s bi, même si le

bro illage est s sceptible d’en

compromettre le fonctionnement.

Table of contents

Other Honeywell Control Unit manuals

Honeywell

Honeywell CF4680 User manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell VP512A User manual

Honeywell

Honeywell FALCON MJ Pulse/M-Bus User manual

Honeywell

Honeywell WV8840B User manual

Honeywell

Honeywell AlarmNet IGSMHS Assembly instructions

Honeywell

Honeywell S89E User manual

Honeywell

Honeywell CIPer 30 User manual

Honeywell

Honeywell VF5000 Series User manual

Honeywell

Honeywell Notifier M710E-CZR User manual

Honeywell

Honeywell AM-1 Series User manual

Honeywell

Honeywell 7800 SERIES Operation manual

Honeywell

Honeywell FIRE-LITE ALARMS TS540/1 User manual

Honeywell

Honeywell DIAL-SET DS05C Operation manual

Honeywell

Honeywell MV300 User manual

Honeywell

Honeywell TM300 User manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell PRO32OUT User manual

Honeywell

Honeywell TRADELINE VR8345M User manual

Honeywell

Honeywell Braukmann DH300 User manual

Honeywell

Honeywell M5410C1001 User manual

Honeywell

Honeywell SM110 User manual

Honeywell

Honeywell Ex-Or CDH8U5 Installation and operation manual

Honeywell

Honeywell 7800 SERIES User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual