Honeywell NOTIFIER FW-MM User manual

FIGURE 2. FACEPLATE INTERIOR

MAGNET LOCA

TION

(DO NOT REMOVE)

C1098-00

BATTERY REPLACEMENT

Low battery levels on the wireless devices are displayed as a trouble in the

FACP. Therefore when the message “TROUBLE BATTERY LOW” is displayed,

replace the battery in the device. This message is an indication that approxi-

mately one week of battery life remains.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Notifier system control panel (list available from Notifier).

To replace the batteries in a wireless device use the following steps:

1. Have 4 CR123A (or DL123A) batteries available

2. Remove the faceplate from the module.

3. Open the battery compartment. (See Figure 3.)

4. Remove the used batteries and replace with new batteries. The battery com-

partment is designed such that the batteries can only align in the appropri-

ate direction. Do not force the batteries into the openings.

5. Replace the battery compartment cover.

6. Replace the faceplace.

SPECIFICATIONS

Maximum Operating Voltage: 3.3 VDC

Maximum Current Draw: 5.0 mA (LED on)

Average Operating Current: 210 µA, 3.9k EOL

EOL Resistance: 3.9K Ohms

Maximum IDC Wiring Resistance: 10 Ohms

Maximum IDC Voltage: 3.2 Volts

Maximum Average IDC Current: 5.5 µA

Maximum Transmit RF Power: 17 dBm

Radio Frequency Range: 902-928 MHz

Temperature Range: 32°F to 120°F (0°C to 49°C)

Humidity: 10% to 93% Non-condensing

Battery Type: 4 Panasonic CR123A or 4 Duracell DL123A

Battery Life: 2 year minimum

Battery Replacement: Upon TROUBLE BATTERY LOW display and/or during annual maintenance

Dimensions: 4¼ in. H x 4¼ in. W x 1½ in. D

Accessories: SMB500(-WH) electrical box (preferred mounting option)

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the control panel installation manual and the SWIFT® Wireless Manual for

detailed system information. If the modules will be installed in an existing op-

erational system, inform the operator and local authority that the system will

be temporarily out of service. Disconnect power to the control panel before

installing the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The FW-MM(A) Monitor Module is intended for use with a wireless gateway

or wireless fire alarm control panel (FACP) to interface with a device having

contacts used to signal status conditions. The input to the monitor module is

non-latching and does not require a reset. The device communicates through

a robust, bi-directional mesh network to the gateway and/or FACP. Rotary

dial switches are provided for setting the module’s address. The module has a

panel controlled LED indicator. (See Figure 1.)

FIGURE 1. CONTROLS AND INDICATORS

C1095C-00

FACEPLATE

The faceplate includes a magnet for activation and tamper resistance. (See

Figure 2.) The faceplate magnet activates communication to the panel, there-

fore, the faceplate must be installed for the module to work properly. The

magnet also activates a supervisory tamper fault at the panel if the nameplate

is removed. Do NOT remove this magnet. The faceplate for a wireless module

CANNOT be replaced with the faceplate of a standard wired module.

1 I56-4067-005

7/27/2021

FW-MM(A) Wireless Monitor Module

I56-4067-005

INSTALLATION AND MAINTENANCE INSTRUCTIONS

12 Clintonville Road

Northford, CT 06472-1653

Phone: 203.484.7161

2 I56-4067-005

MOUNTING

The FW-MM(A) mounts directly to an SMB500(-WH) electrical box. (See

Figure 4.) To avoid interference with the wireless network metal elec-

trical boxes are NOT recommended. Non-metal surface mounted elec-

trical boxes (SMB500/SMB500-WH) are available from Notifier. If not

using an SMB500(-WH), the minimum mounting opening dimensions for the

FW-MM(A) are 4 in. X 3¾ in. x 1½ in. deep.

NOTE: Do not attach the module to temporary structures such that the place-

ment could be altered.

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and reg-

ulations. This module is intended for power limited wiring only. FW-MM(A)

must be within 3 feet of monitored device when using field wiring or 20 feet

in non-metallic conduit. In Canada, wiring methods shall be in accordance

with CSA C22.1 Safety Standard for Electrical Installations, Canadian Electri-

cal Code, Part 1, Section 32.

1. Install module wiring in accor-

dance with the job drawings

and appropriate wiring dia-

grams.

2. Set the address on the module

per job drawings.

3. Secure module to electrical

box (supplied by installer), as

shown in Figure 3.

C1096-00

C1097-00

FIGURE 4. MODULE MOUNTINGFIGURE 3. BATTERY COMPARTMENT

BATTERY

COMPARTMENT

DOOR

BATTERY

COMPARTMENT

C2002-00

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Do not make changes to the equipment. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

FCC STATEMENT

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

RAPPORT D’IC

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

INSTITUTO FEDERAL DE TELECOMUNICACIONES

This device utilizes the Honeywell915 rev A radio module and complies with IFETEL standard(s). IFT: RCPHOSW14-1983

Use of these products in combination with non-Honeywell products in a wireless mesh

network, or to access, monitor or control devices in a wireless mesh nework via the inter-

net or another external wide area network, may require a separate license from Sipco, LLC.

For more information, contact Sipco, LLC or Ipco, LLC at 8215 Roswell Rd., Building 900,

Suite 950, Atlanta, GA 30350, or at www.sipocollc.com or www.intusiq.com.

LICENSING STATEMENT

FIGURE 5. TYPICAL MONITORING CONFIGURATION

WIRELESS

MONITOR MODULE

ONLY ONE UL/ULC LISTED CONTACT

CLOSURE MAY BE USED

POWER LIMITED

3.1 VDC MAX

3.9K EOL

RESISTOR

A2143-10

INSTALL CONTACT CLOSURE DEVICES PER MANUFACTURER’S

INSTALLATION INSTRUCTIONS. WIRELESS MONITOR MODULE MUST BE

WITHIN 3 FEET (1M) OF MONITORED DEVICE WHEN USING FIELD WIRING

OR 20 FEET (6.1M) IN NON-METALLIC CONDUIT. C1099GC-00

Notifier®and SWIFT ® are registered trademarks of Honeywell International, Inc.

This manual suits for next models

Table of contents

Other Honeywell Control Unit manuals

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell 804973 User manual

Honeywell

Honeywell LTE-L57V User manual

Honeywell

Honeywell CENTRALINE CLCM1H112 User manual

Honeywell

Honeywell VS8421 User manual

Honeywell

Honeywell 7800 SERIES Operation manual

Honeywell

Honeywell MAXON 8730 Series User manual

Honeywell

Honeywell V5097A-E Operation manual

Honeywell

Honeywell RK-MCU Instruction sheet

Honeywell

Honeywell V305 Series User manual

Honeywell

Honeywell LTE-L57A User manual

Honeywell

Honeywell VP513A User manual

Honeywell

Honeywell VR8305 User manual

Honeywell

Honeywell VR8405 User manual

Honeywell

Honeywell krom schroder BCU 440 User manual

Honeywell

Honeywell Temaline TK-S014 User manual

Honeywell

Honeywell MDC108200 User manual

Honeywell

Honeywell 7800 SERIES User manual

Honeywell

Honeywell Notifier XP6-R User manual

Honeywell

Honeywell Velociti AOM-2RF User manual

Honeywell

Honeywell VISTA-ICM Assembly instructions

Honeywell

Honeywell V4073A User manual

Honeywell

Honeywell Alwa-Kombi-4 User manual

Honeywell

Honeywell V48F User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual