Honeywell GSMVLP5 Assembly instructions

800-08115 1/11 Rev. B

GSMVLP5 GSM and

ILP5 Ethernet

Communications Modules

Installation and Setup Guide

Installing Communication Modules

RF Exposure

WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna(s) or transmitter.

Installing the GSMVLP5 in the LYNX Touch Series Control

Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the

module in the LYNX Touch.

1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).

5000-100-186-V0

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY

CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS

DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

800-08126 1/11 Rev A

LYNX TOUCH SERIES

COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000

RINGER EQUIVALENCE: 0.1B

IC MODEL: LYNXTOUCH1

CONTAINS TRANSMITTER MODULE

IC: 7830A-MC55I

FCC ID: QIPMC55I

800-08334 2/11 Rev A

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

LYNX TOUCH SERIES

IC MODEL: LYNXTOUCHG1

Figure 1. FCC/IC Label Location

2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 2).

3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly

seated into the receptacle on the control (Refer to Figure 2).

4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).

5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.

Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and

Setup Guide (P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

SCREW

(3)

SIM

CARD

5000-100-151-V1

ROTATED

180

CONNECTOR

BOARD

CONNECTOR

BOARD

RECEPTACLE

GSMVLP5

LYNX TOUCH

LOCKING TABS

Figure 2. Installing the GSMVLP5 in the LYNX Touch

Installing the ILP5 in the LYNX Touch Series Control

Ensure that the connector board and cable are securely installed in the ILP5 before installing the module

the LYNX Touch.

1. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 3).

2. Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer to the back case of the LYNX

Touch (Refer to Figure 3).

3. Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case (Refer to Figure 3).

4. Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated

into the receptacle on the control (Refer to Figure 3).

5. Secure the ILP5 with the three provided screws (Refer to Figure 3).

6. Insert the ILP5 receptacle and spacer into the slot on the back case (Refer to Figure 3).

7. Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap (Refer to

Figure 3).

8. Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the

“Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide

(P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

5000-100-154-V1

SCREW

(3)

ROTATED

180

CONNECTOR

BOARD

RJ45

RECEPTACLE

CONNECTOR BOARD

RECEPTACLE

ILP5

LYNX TOUCH

TIE

WRAP

POINT

REMOVE ILP5

SPACER

ILP5 SPACER

REMOVE ILP5

KNOCKOUT

TIE

WRAP

(1)

RJ45 RECEPTACLE

LYNX TOUCH

ALTERNATE INSTALLATION

LOCKING TABS

ETHERNET CABLE

TO ILP5

Figure 3. Installing the ILP5 in the LYNX Touch

Electrical Specifications

GSMVLP5

Voltage Input 5V

Current

Idle 15 mA, standby

Average 300mA, average transmit

Peak 1.6A peak transmit, 25% duty cycle

ILP5

Voltage Input 5V

Current: 83 mA, 100 Base T with traffic

41 mA, 10 Base T with traffic

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Ê800-08115!Š

800-08115 1/11 Rev. B

Table of contents

Other Honeywell Control Unit manuals

Honeywell

Honeywell V4730C User manual

Honeywell

Honeywell VGF User manual

Honeywell

Honeywell V5004TF User manual

Honeywell

Honeywell Kromschroder GIK Series User manual

Honeywell

Honeywell CentraLine CLIOL822A Operation manual

Honeywell

Honeywell S4560 User manual

Honeywell

Honeywell VS8521 User manual

Honeywell

Honeywell 7800 SERIES Operation manual

Honeywell

Honeywell SM152 AA Series User manual

Honeywell

Honeywell ADEMCO 5800RL Assembly instructions

Honeywell

Honeywell M6410A Operation manual

Honeywell

Honeywell Silent knight 5895XL User manual

Honeywell

Honeywell SM110 User manual

Honeywell

Honeywell Notifier NFG-8 User manual

Honeywell

Honeywell ST7700 User manual

Honeywell

Honeywell Notifier FCM-1-REL User manual

Honeywell

Honeywell VP525C User manual

Honeywell

Honeywell V5421C User manual

Honeywell

Honeywell RF CM61NG User manual

Honeywell

Honeywell MI-DCZME User manual

Honeywell

Honeywell IDENT-KEY Series Instruction manual

Honeywell

Honeywell PS300 User manual

Honeywell

Honeywell NOTIFIER M700 Series User manual

Honeywell

Honeywell hmr3000 TruePoint User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual