Honeywell Xenon 1900H User manual

Enhanced Xenon™ 1900H

Corded Area-Imaging Scanner for Healthcare

Quick Start Guide

Rev A

8/15

Aller à www.honeywellaidc.com pour le français.

Vai a www.honeywellaidc.com per l'italiano.

Gehe zu www.honeywellaidc.com für Deutsch.

Ir a www.honeywellaidc.com para español.

Idźna stronę: www.honeywellaidc.com po quick start w języku polskim.

Перейти на русскоязычный сайт www.honeywellaidc.com.

Pro češtinu jdi na www.honeywellaidc.com.

Pre slovenčinu choďna www.honeywellaidc.com

Para Português, acesse www.honeywellaidc.com.br.

日本語 : www.honeywellaidc.com をご覧ください。

如要到中国 www.honeywellaidc.com（简体）。

查看繁体版请登陆 www.honeywellaidc.com

한글 www.honeywellaidc.com 로이동합니다 .

ʲʡʤʱʸʢʬʡʺʩʸˬʺʡʥʺʫʡʨʰʸʨʰʩʠʤʸʺʠʬʸʥʡʲwww.honeywellaidc.com.

Çäè´á Åàˆ moc.cdiallewyenoh.www ààú¬ ÇàõÑéí¬

Note: Refer to your user’s guide for information about cleaning your

device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off computer’s power before connecting the scanner, then

power up the computer once the scanner is fully connected.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connecting the Scanner

USB:

Keyboard Wedge:

RS232 Serial Port:

Reading Techniques

The view finder projects an aiming

beam that should be centered over

the bar code, but it can be

positioned in any direction for a

good read.

Hold the scanner over the bar code,

pull the trigger, and center the

aiming beam on the bar code.

The aiming beam is smaller when

the scanner is closer to the code and larger when it is farther from the

code. Hold the scanner close to smaller bar codes, and farther away

from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to

tilt the scanner at an angle so the bar code can be scanned.

Standard Product Defaults

The following bar code resets all standard product default settings.

Standard Product Defaults

USB Serial

Scan the following code to program the scanner to emulate a regular

RS232-based COM Port. If you are using a Microsoft® Windows®

PC, you will need to download a driver from the Honeywell website

(www.honeywellaidc.com). The driver will use the next available

COM Port number. Apple® Macintosh computers recognize the

scanner as a USB CDC class device and automatically use a class

driver.

USB Serial

Note: No extra configuration (e.g., baud rate) is necessary.

USB PC Keyboard

Scan the following code to program the scanner for a USB PC

Keyboard.

USB PC Keyboard

Epic

Scan the following bar code to configure your device to communicate

with an Epic software application.

EMR Application

Meditech®

Scan the following bar code to configure your device to communicate

with a Meditech software application.

Meditech Application

Quiet Operations

The following codes configure the scanner for quiet modes that do

not disturb resting patients.

Silent Mode with Flashing LED

Scan the following bar code to completely silence the scanner. When

a bar code is scanned, the LED and aimer flash 5 times. Green

indicates a good scan, red indicates a bad scan.

Silent Mode with Flashing LED

Silent Mode with Long LED

Scan the following bar code to completely silence the scanner. When

a bar code is scanned, the LED and aimer remain solidly lit for 1

second. Green indicates a good scan, red indicates a bad scan.

Silent Mode with Long LED

Very Low Beeper (Nighttime Mode)

The following bar code programs the scanner for a very low beep.

When a bar code is scanned, the scanner emits a very soft beep.

Nighttime Mode

Low Beeper (Daytime Mode)

The following bar code programs the scanner for a low volume.

When a bar code is scanned, the scanner emits a low beep.

Daytime Mode

Trigger

The following bar codes will allow you to use the scanner in Manual

Trigger - Normal Mode (need to press the trigger to read) or

Presentation mode (the scanner is activated when it “sees” a bar

code).

Manual Trigger - Normal

(Default)

Presentation Mode

Streaming Presentation™

When in Streaming Presentation mode, the scanner leaves the scan

illumination on all the time and continuously searches for bar codes.

Streaming Presentation Mode

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab

Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a Code ID prefix to all

symbologies at once.

Add Code ID Prefix To All Symbologies

(Temporary)

Note: For a complete list of Code IDs, see the User’s Guide for your

product at our website, www.honeywellaidc.com.

Keyboard Country

Scan the appropriate country code below to program the keyboard

layout for your country or language. By default, national character

replacements are used for the following characters: #$@[\]^‘{|}~

Refer to the ISO 646 Character Replacements chart in your User’s

Guide to view the character replacements for each country.

USA (Default)

Belgium

Denmark

Finland

France

Germany/Austria

Great Britain

Table of contents

Honeywell Xenon 1900H User manual

Popular Barcode Reader manuals by other brands