Honeywell Xenon 1910 User manual

Xenon™ 1900/1910
Corded Area-Imaging Scanner
Quick Start Guide
NG2D-QS Rev D
8/12
Aller à www.honeywellaidc.com pour le français. 
Vai a www.honeywellaidc.com per l'italiano. 
Gehe zu www.honeywellaidc.com für Deutsch. 
Ir a www.honeywellaidc.com para español. 
Para Português, acesse www.honeywellaidc.com.br. 
Перейти на русскоязычный сайт www.honeywellaidc.com. 
Pro češtinu jdi na www.honeywellaidc.com. 
Pre slovenčinu choď na www.honeywellaidc.com 
日本語 :  www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .

Note: Refer to your user’s guide for information about cleaning your

device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off computer’s power before connecting the scanner, then

power up the computer once the scanner is fully connected.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connecting the Scanner

USB:

Keyboard Wedge:

RS232 Serial Port:

RS485:

Reading Techniques

The view finder projects an aiming

beam that should be centered over

the bar code, but it can be

positioned in any direction for a

good read.

Hold the scanner over the bar code,

pull the trigger, and center the

aiming beam on the bar code.

The aiming beam is smaller when

the scanner is closer to the code and larger when it is farther from the

code. Hold the scanner close to smaller bar codes, and farther away

from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to

tilt the scanner at an angle so the bar code can be scanned.

Standard Product Defaults

The following bar code resets all standard product default settings.

Standard Product Defaults

RS485 Interface

The RS485 interface defaults to port 5B. If you have an IBM POS

terminal using port 9B, scan the appropriate code below to program

the terminal, then power cycle the cash register.

Note: For additional RS485 interface selections, see the User’s

Guide for your product at our website,

www.honeywellaidc.com.

USB Serial

Scan the following code to program the scanner to emulate a regular

RS232-based COM Port. If you are using a Microsoft® Windows®

PC, you will need to download a driver from the Honeywell website

(www.honeywellaidc.com). The driver will use the next available

COM Port number. Apple® Macintosh computers recognize the

scanner as a USB CDC class device and automatically use a class

driver.

Note: No extra configuration (e.g., baud rate) is necessary.

IBM Port 9B HHBCR-1

Interface

IBM Port 9B HHBCR-2

Interface

USB Serial

USB PC Keyboard

Scan the following code to program the scanner for a USB PC

Keyboard.

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan

the numeric bar code(s) from page 2, then the Save bar code to

program the keyboard for your country. As a general rule, the

following characters are not supported by the scanner for countries

other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

Country Code Scan Country Code Scan

Belgium 1 Italy 5

Denmark 8 Norway 9

Finland 2 Spain 10

France 3 Switzerland 6

Germany/Austria 4 USA (Default) 0

Great Britain 7

USB PC Keyboard

Program Keyboard Country

Save

Note: For a complete list of country codes, see the User’s Guide for

your product at our website, www.honeywellaidc.com.

Trigger

The following bar codes will allow you to use the scanner in Manual

Trigger - Normal Mode (need to press the trigger to read) or

Presentation mode (the scanner is activated when it “sees” a bar

code).

Streaming Presentation™

When in Streaming Presentation mode, the scanner leaves the scan

illumination on all the time and continuously searches for bar codes.

Manual Trigger - Normal

(Default)

Presentation Mode

Streaming Presentation Mode

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab

Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

Add Code ID Prefix to all Symbologies

Scan the following bar code if you wish to add a Code ID prefix to all

symbologies at once.

Note: For a complete list of Code IDs, see the User’s Guide for your

product at our website, www.honeywellaidc.com.

Add CR Suffix

Remove Suffix

Add Tab Suffix

Add Code ID Prefix To All Symbologies

(Temporary)

Function Code Transmit

When this selection is enabled and function codes are contained

within the scanned data, the scanner transmits the function code to

the terminal. Charts of these function codes are provided in your

User’s Guide. When the scanner is in keyboard wedge mode, the

scan code is converted to a key code before it is transmitted.

Enable

(Default)

Disable

Other manuals for Xenon 1910

This manual suits for next models

Table of contents

Honeywell Xenon 1910 User manual

Popular Barcode Reader manuals by other brands