Honeywell Granit 1920i User manual
.
Granit 1920i
Industrial Direct Part Mark (DPM) Area-Imaging Scanner
Quick Start Guide
1920i-EN-QS Rev A
7/17
1
Note: Refer to your user’s guide for information about cleaning
your device.
Get Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
2
Connect the Scanner
When connecting the scanner, make sure the cable is pushed
tightly into the scanner. Loosen the locking plate and slide it
over the base of the cable connector to lock the cable in place.
Tighten the screw.
3
USB:
4
RS232 Serial Port:
Reading Techniques
The Granit 1920i scanner uses a red aiming dot to locate bar
codes. Center the aimer on the bar code. If the bar code being
scanned is on a shiny or highly reflective surface, you may need
to tilt the scanner slightly to read the code.
5
Standard Product Defaults
The following bar code resets all standard product default set-
tings.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (www.honeywellaidc.com). The driver will use the
next available COM Port number. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Standard Product
Defaults
USB Serial
USB PC Keyboard
6
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from page 11, then the Save bar code to
program the keyboard for your country. By default, national
character replacements are used for the following characters: #
$ @ [ \ ] ^ ‘ { | } ~.
Note: For a complete list of country codes, see the User’s Guide
for your product.
Country Code Scan Country Code Scan
Arabia 91 Korea 93
Belgium 1 Portugal 13
China 92 Russia 26
France 3 Spain 10
Germany/Austria 4 Sweden/Finland 2
Great Britain 7 Switzerland 6
Hungary 19 Thailand 94
IBM Financial 90 Turkey (Q) 24
Italy 5 USA (Default) 0
Japan 28 Vietnam 95
Program Keyboard Country
Save
7
Active Aimer
By default, the scanner and the aiming beam remain off until
you press the trigger. When Active Aimer is set to On, whenever
the scanner is moved, the aiming beam appears so you can aim,
then scan a bar code with a trigger press.
DPM Illumination Settings
By default, the Granit 1920i cycles through the Direct Illumina-
tion - Top and Bottom, and Indirect Illumination settings. To fur-
ther refine the scanner’s ability to read DPM codes, scan one of
the following four illumination setting codes. Only one of these
illumination settings can be used.
Direct Illumination - Top and Bottom
This setting enables both top and bottom illumination. It is rec-
ommend when reading printed label bar codes and DPMs on
highly reflective surfaces.
Active Aimer On
8
Direct Illumination - Bottom
This setting enables just the bottom illumination. It is recom-
mend when primarily reading dot peen bar codes. You may need
to tilt the scanner at an angle to read from reflective surfaces.
Indirect Illumination
This setting is recommend when reading bar codes on curved or
rough surfaces.
Low Contrast Codes
This setting is recommend when reading very low contrast bar
codes. Scan the following code to program the scanner to cycle
through both Direct Illumination - Top and Bottom and Indirect
Illumination with multiple exposure settings.
9
Low Contrast Data Matrix Enhancements
The Granit 1920i scanner reads low contrast Data Matrix codes
by default. However, if you are having trouble reading non-dot
peen Data Matrix bar codes, it may be helpful to scan Low Con-
trast Data Matrix Enhancements Off.
Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add Tab
Suffix bar code. Otherwise, scan the Remove Suffix bar code to
remove the suffixes.
* Low Contrast Data Matrix
Enhancements On
Low Contrast Data Matrix
Enhancements Off
Add CR Suffix
Add Tab Suffix
Remove Suffix
Table of contents
Other Honeywell Barcode Reader manuals
Honeywell
Honeywell 4600g User manual
Honeywell
Honeywell ms2420 User manual
Honeywell
Honeywell ms2420 User manual
Honeywell
Honeywell I-Class Mark II User manual
Honeywell
Honeywell 1400gPDF User manual
Honeywell
Honeywell VoyagerGS MS9590i User manual
Honeywell
Honeywell 8680i Series User manual
Honeywell
Honeywell XENON 1902G-BF User manual
Honeywell
Honeywell VoyagerGS 9590 Series User manual
Honeywell
Honeywell Orbit MS7120 User manual
Honeywell
Honeywell 7120 Orbit User manual
Honeywell
Honeywell MS9520 Voyager User manual
Honeywell
Honeywell Xenon XP 195 Series User manual
Honeywell
Honeywell VoyagerCG MS9540 User manual
Honeywell
Honeywell 3800gPDF - Hand Held Decoding Linear Imager User manual
Honeywell
Honeywell Voyager 1602g User manual
Honeywell
Honeywell 8670 User manual
Honeywell
Honeywell Solaris MS7820 User manual
Honeywell
Honeywell Quick Check 890 User manual
Honeywell
Honeywell Eclipse MS5100 Series User manual
