Honeywell IS4225 ScanGlove User manual

IS4225 ScanGlove®

Laser Bar Code Scanner

Installation and User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in

specifications and other information contained in this document without prior

notice, and the reader should in all cases consult HII to determine whether any

such changes have been made. The information in this publication does not

represent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein: nor for incidental or consequential damages resulting from the furnishing,

performance, or use of this manual.

This document contains propriety information that is protected by copyright. All

rights reserved. No part of this document may be photocopied, reproduced, or

translated into another language without the prior written consent of HII.

Web Address: www.honeywellaidc.com

Trademarks

Metrologic, MetroSelect, and ScanQuest are trademarks or registered

trademarks of Metrologic Instruments, Inc. or Honeywell International Inc.

Other product names mentioned in this manual may be trademarks or registered

trademarks of their respective companies and are the property of their respective

owners.

iii

TABLE OF CONTENTS

Introduction........................................................................................................... 1

Scanner and Accessories..................................................................................... 1

Scanner Installation.............................................................................................. 2

Scanner Configuration to the Host System........................................................... 3

Parts of the Scanner............................................................................................. 4

Visual Indicators ................................................................................................... 5

Audible Indicators................................................................................................. 6

Labels................................................................................................................... 7

Maintenance......................................................................................................... 8

Depth of Field ....................................................................................................... 9

Object Detection Device..................................................................................... 10

Specifications ..................................................................................................... 12

Default Settings .................................................................................................. 13

Troubleshooting Guide ....................................................................................... 19

Regulatory Compliance ...................................................................................... 20

Patents ............................................................................................................... 23

Limited Warranty ................................................................................................ 24

Index................................................................................................................... 25

Customer Support .............................................................................................. 27

Technical Assistance ..................................................................................... 27

Product Service and Repair........................................................................... 28

INTRODUCTION

The IS4225 ScanGlove®is a fully automatic single-line laser barcode scanner.

The ScanGlove is designed to be used as a “hands-free” wearable scanner or a

stationary desktop scanner.

Every ScanGlove is equipped with an object detection technology that allows the

scanner to read bar codes automatically as the operator presents the bar code to

the scanner. Additional features include; 52 scan lines a second, short, or long-

range activation and two universal glove sizes with left and right-hand

capabilities.

The IS4225 has built in decoding for applications that use a RS232, Keyboard

Wedge, Stand Alone Keyboard, Light Pen Emulation, or USB interfaces. All

models have Flash upgradeable firmware. For additional information on other

system interfaces, please call a Customer Service Representative.

SCANGLOVE MODEL NO. INTERFACE

IS4225-38 USB Keyboard

IS4225-41D RS232 with Breakaway Cable and DIN Connector

IS4225-47 PC Keyboard Wedge and Stand Alone Keyboard

IS4225-81 Full RS232 and Light Pen Emulation

SCANNER AND ACCESSORIES

PART NUMBER DESCRIPTION

IS4225 IS4225 Laser Scanner

00-02258 Installation and User’s Guide

00-02544 MetroSelect®Single-Line Configuration Guide

45-45455 Black Adjustable Glove

If any item is missing or to order additional items, contact the dealer, distributor or contact a

customer service representative.

SCANNER INSTALLATION

1. Turn off power to the host system.

2. Connect the communication cable to the proper port on the host device.

3. Turn on power to the host system.

When the IS4225 first receives power, the red LED will flash, the

green LED will flash, and then the scanner will beep once.

See power source caution statement on page 7 of this manual.

To maintain compliance with federal regulations 21 CFR, Part 1040.10,

section (f)(6) the scanner must be plugged into an electrical outlet with a

switch accessible to the user or be powered by a host system containing a

switch that will disable power to the scanner.

SCANNER CONFIGURATION TO THE HOST SYSTEM

The IS4225 is shipped from the factory pre-configured to a set of default

parameters. It may be necessary to change the default parameters to match the

host system’s requirements or to enable additional scanner functions. For a list

of possible parameter settings, refer to the Default Settings section of this guide.

To modify the scanner’s default parameters follow the steps below using the

bar codes located in the MetroSelect Single-Line Configuration Guide

(PN 00-02544).

1. Scan the

ENTER CONFIGURATION MODE bar code to enter configuration mode.

The scanner will beep three times.

2. Scan the bar code(s) for the desired parameter(s).

The scanner will beep once.

3. Scan the

EXIT CONFIGURATION MODE bar code to exit and save the new

parameter settings. The scanner will beep three times.

If during the configuration process, there is a need to return the

scanner to the original factory settings, scan the recall defaults bar

code in the MetroSelect Configuration Guide. All settings selected

during that session or any previous sessions are discarded when you

scan the recall defaults code.

The IS4225 with RS232 interface can also be configured using MetroSet®2which

is a PC-based utility software and available for download at

www.honeywellaidc.com. In addition, this interface can be configured using serial

configuration mode. For details, refer to the MetroSelect®Single-Line

Configuration Guide (PN 00-02544.)

PARTS OF THE SCANNER

Figure 1. Scanner Parts

Item

No. Description

 Green LED

When a bar code is read successfully, the green LED will flash.

 Red LED

When the red LED is illuminated, the laser is on.

 Red Output Window (Laser Aperture)



Object Detection Device

If a specified time has elapsed without any scanning, the unit will

enter a “standby” mode. To reactivate the unit, place an object in

front of the object detection field. The red LED will turn on when

the scanner is ready to scan.

 Communication/Power Cable

This cable’s termination is application dependent.

VISUAL INDICATORS

There is a red and a green LED located on the top of the scanner. When the

scanner is on, the flashing or constant, illumination of the LEDs indicates the

status of the current scan and the scanner.

No Red LED Illumination of the LEDs will not occur if the scanner has

remained dormant for a specified time and the scanner is

not receiving power from the host. To reactivate the unit,

direct the output window up then down toward the object.

Red Flash;

Green Flash;

Steady Red

When the scanner first receives power, the red LED will

flash, followed by the green LED, and then the unit will

beep once. The red LED will stay on after it flashes once.

Steady Red When the laser is on, the red LED will be on. This occurs

when an object is detected in the scan field. If the scanner

cannot detect a bar code within approximately 2.5 seconds,

the unit will go into standby mode then the red LED will

shut off indicating that the laser is no longer on.

Steady Red

LED; Green

Flash

When the scanner successfully reads a bar code, the green

LED will flash and the unit will beep once. If the green LED

does not flash or the scanner does not beep, then the bar

code was not successfully read.

Repetitive Red

LED Flashing

The red LED will flash repeatedly when the object detection

device is detecting a stationary object in the scan field. To

eliminate this disturbance, direct the scan window toward a

different location or remove the stationary object from the

object detection field.

Steady Green

LED

After a successful scan, the scanner transmits the data to

the host device. When the host is not ready to receive the

information, the green LED will remain on until data can

transmit.

AUDIBLE INDICATORS

The scanner provides sounds to signal certain conditions. To change the volume

(four settings are available) or turn the beeper off, refer to Scanner Operation:

Beeper Options in the MetroSelect Single-Line Configuration Guide (PN 00-

02544).

One Beep When the scanner first receives power, the red LED will

flash, followed by the green LED, and then the scanner

will beep once. After the scanner performs this start-up

sequence, the scanner is ready to scan.

When the scanner successfully reads a bar code, the

green light will flash and the unit will beep once. If the

green LED does not flash or the scanner does not beep,

then the bar code read is not successful.

Razzberry Tone If, upon power up, the scanner emits a razzberry tone the

scanner has failed diagnostics.

The scanner can be configured to emit a

razzberry tone when the timeout occurs during

communication between the host and scanner.

Refer to Scanner Operation: Communication

Timeout Options in the MetroSelect Single-Line

Guide.

Three Beeps When entering configuration mode, the green LED will

flash three times while the scanner simultaneously beeps

three times. When exiting configuration mode, the same

visual and audible indications will occur. After the

sequence is completed, the red LED will turn off.

The scanner can be programmed to emit three

beeps when the timeout occurs during

communication between the host and scanner.

Refer to Scanner Operation: Communication

Timeout Options in the MetroSelect Single-Line

Guide.

Table of contents

Honeywell IS4225 ScanGlove User manual

Popular Barcode Reader manuals by other brands