Honeywell Xenon CCB01-010BT-BF User manual
Xenon™ XP 1952h/1952h-BF
CCB01-010BT/CCB01-010BT-BF
CCB-H-010BT/CCB-H-010BT-BF
Cordless Area-Imaging Scanner for Healthcare and Charge Bases
Quick Start Guide
1952HC-HCBF-EN-QS-01 Rev A
04/19
1
Agency Model: 1952, 1952-BF, CCB01-010BT, CCB01-010BT-BF,
CCB-H-010BT, CCB-H-010BT-BF
Note: Refer to your User Guide for information about cleaning
your device.
Get Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Once the base is connected and powered up, follow the Link the
Scanner (page 5) instructions to link the scanner to the base.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
2
Connect the Scanner
USB:
Note: If you are charging the scanner using the USB cable, the
current available for charging is reduced and charge times
are increased. Charging via the power supply is faster.
CCB-H-010BT or CCB-H-010BT-BF Base:
CCB01-010BT or CCB01-010BT-BF Base:
3
Keyboard Wedge:
CCB-H-010BT or CCB-H-010BT-BF Base:
CCB01-010BT or CCB01-010BT-BF Base:
4
RS232 Serial Port:
CCB-H-010BT or CCB-H-010BT-BF Base:
CCB01-010BT or CCB01-010BT-BF Base:
5
Link the Scanner
Use the following procedure to configure all scanners so they
automatically connect to the base.
1. Scan the bar code on the base.
2. Place the scanner into the base.
3. Power cycle the base to complete the link and establish
communication between the base and scanner.
When the scanner is in the base, the green LED on the base
flashes to indicate the scanner’s battery is charging.
Unlink the Scanner
If the base has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the
base. Scan the Unlink Scanner bar code to unlink a scanner.
Unlink Scanner
6
Reading Techniques
The view finder projects an aiming beam that
should be centered over the bar code, but it
can be positioned in any direction for a good
read.
Standard Product Defaults
The following bar code resets all standard
product default settings.
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
If you are using a Microsoft® Windows® PC, you must
download a driver from the Honeywell website. The
driver will use the next available COM Port number.
Standard Product Defaults
USB Serial
7
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Epic
Scan the following bar code to configure your device to commu-
nicate with an Epic software application.
After scanning this code, you must put the scanner into the base
or scan the linking bar code on the base or Access Point to relink
your scanner.
USB PC Keyboard
EMR Application
8
Meditech®
Scan the following bar code to configure your device to commu-
nicate with a Meditech software application.
After scanning this code, you must put the scanner into the base
or scan the linking bar code on the base or Access Point to relink
your scanner.
Quiet Operations
The following codes configure the scanner and base to quiet
modes for scanning that does not disturb resting patients.
Meditech Application
9
Silent Mode with Flashing LED
Scan the following bar code to completely silence the base and
scanner. When a bar code is scanned, the LED and aimer flash 5
times. Green indicates a good scan, red indicates a bad scan.
Silent Mode with Long LED
Scan the following bar code to completely silence the base and
scanner. When a bar code is scanned, the LED and aimer remain
solidly lit for 1 second. Green indicates a good scan, red indi-
cates a bad scan.
Silent Mode with Flashing LED
Silent Mode with Long LED
This manual suits for next models
5
Table of contents
Other Honeywell Barcode Reader manuals
Honeywell
Honeywell HH1800 User manual
Honeywell
Honeywell 8680i Series User manual
Honeywell
Honeywell Hyperion 1300G User manual
Honeywell
Honeywell 4820HDHM User manual
Honeywell
Honeywell CM4680 User manual
Honeywell
Honeywell VOYAGER 1200G User manual
Honeywell
Honeywell HF800 Series User manual
Honeywell
Honeywell Orbit MS7120 User manual
Honeywell
Honeywell OrbitCG MS7180 User manual
Honeywell
Honeywell 2020 User manual
Honeywell
Honeywell MX7 Tecton User manual
Honeywell
Honeywell Granit XP 199 i Series User manual
Honeywell
Honeywell 3800i User manual
Honeywell
Honeywell MS1890 Focus User manual
Honeywell
Honeywell IS4225 ScanGlove User manual
Honeywell
Honeywell XL 800 Series User manual
Honeywell
Honeywell Vuquest 3320g User manual
Honeywell
Honeywell Orbit MS7120 User manual
Honeywell
Honeywell MK3780-71A38 User manual
Honeywell
Honeywell MS2431 User manual
