Honeywell 8680i Series User manual
8680i
Wearable Scanner
Quick Start Guide
8680-EN-QS Rev (a)
3/18
Preliminary
Draft3/13/18
1
Overview
Note: The battery must be fully charged before the first use. An
MB4-BAT-SCN02 or an MB4-SCN02 Charging Station
must be purchased separately.
Battery
Right button
Left button
Trigger Scanner
User window
Battery
latch
2
Attach the Scanner to Your Hand
1. Slide your fingers into the loosened strap.
2. Pull the strap to secure to your fingers.
3
Right or Left Handed Operation
To release the finger trigger, turn over the scanner. Slide the
latch toward the user window to release the finger trigger. Turn
the finger strap around and snap it into place to change the
operation to the correct hand.
4
Power Up the Scanner
Press the trigger for 10 seconds to power up the scanner. The
battery, WiFi, and Bluetooth status appears in the window.
Wrist Position When Scanning
How to Scan a Bar Code
The 8680i scanner has a view finder that projects a bright aimer
line. This aimer line should be centered over the bar code, but it
can be positioned in any direction for a good read.
Warning: Do not stare directly into the laser beam.
Linear bar codes 2D Matrix symbol s
5
The aimer line is smaller when the scanner is closer to the code
and larger when it is farther from the code. Symbologies with
smaller bars or elements (mil size) should be read closer to the
unit. Symbologies with larger bars or elements (mil size) should
be read farther from the unit. To read single or multiple symbols
(on a page or on an object), hold the scanner at an appropriate
distance from the target, press the trigger, and center the aimer
line on the symbol. If the code being scanned is highly reflective
(e.g., laminated), it may be necessary to tilt the code up 15° to
18° to prevent unwanted reflection.
6
Connect the Scanner via Bluetooth
Pair with a Bluetooth Device Using a HID Keyboard
The 8680i scanner can pair with host Bluetooth devices such as
personal computers, laptops, and tablets. This is the default set-
ting for an 8680i scanner. Follow the steps below to establish
one-way communication with the host device.
1. Scan the appropriate Bluetooth HID Keyboard Connect bar
code below.
2. Set your host device so it searches for other Bluetooth
devices. (Refer to your host device’s User’s Guide for pairing
instructions.)
3. Once your host device has located the scanner, select the
8680i scanner name from the list displayed.
4. Some host devices automatically pair with the scanner. If
your host device automatically pairs with the scanner, it
displays a successful pairing message and you do not need
to continue to the next step.
* Bluetooth HID Keyboard
Connect
Bluetooth HID Japanese
Keyboard Connect
7
5. Some PDT hosts display a prompt for a PIN. Ignore this
message.
6. If your host device does not automatically pair with the
scanner, a PIN is displayed. This PIN must be scanned
within 60 seconds. Using the scanner, you must quickly
scan Bluetooth PIN Code below, then scan the numeric bar
code(s) for the PIN code from the chart below, then scan the
Save bar code.
Bluetooth PIN Code
0
1
2
3
4
5
8
The Bluetooth symbol appears in the scanner window when the
scanner pairs with a host.
Pair with an Android™ Device
The 8680i scanner can pair with Android devices.
1. Set your Android device so it searches for other Bluetooth
devices. (Refer to your Android device’s User’s Guide for
pairing instructions.)
2. Scan the BT Connection - Android Device bar code below.
6
7
8
9
Save
BT Connection - Android Device
9
On the Android device, the 8680i scanner is shown as a key-
board. Click on it to pair. The Bluetooth symbol appears in the
scanner window when the scanner pairs with a host.
Disconnect from the Host
Once your scanner has been connected to a host, you must dis-
connect it in order to communicate with a different device. Scan
the Bluetooth HID Keyboard Disconnect bar code to unlink the
scanner from the currently linked host.
Tap and Pair
You can pair your Android™ phone with the scanner by touching
the devices together.
1. Touch the Android phone to the scanner.
2. The phone recognizes the scanner and prompts you to pair.
3. Verify the pairing of the scanner in your phone’s Bluetooth
settings.
Pair with a Bluetooth Serial Port - PCs/Laptops
The 8680i scanner can pair with a Bluetooth serial port on a PC
or laptop. Scanning the Non-Base BT Connection bar code
below unlinks your scanner and puts it into a discoverable state.
Once the scanner searches for and connects with a Bluetooth
Bluetooth HID Keyboard Disconnect
Other manuals for 8680i Series
5
Table of contents
Other Honeywell Barcode Reader manuals
Honeywell
Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis User manual
Honeywell
Honeywell Xenon 1910 User manual
Honeywell
Honeywell 3800 Linear Series User manual
Honeywell
Honeywell MK9535-79A540 - MS9535 VoyagerBT - Wireless Portable Barcode... User manual
Honeywell
Honeywell XENON 1902G-BF Dimensions
Honeywell
Honeywell 4600g User manual
Honeywell
Honeywell ms2420 User manual
Honeywell
Honeywell Fusion MS3780 User manual
Honeywell
Honeywell 3800gPDF - Hand Held Decoding Linear Imager User manual
Honeywell
Honeywell 4600g User manual
Honeywell
Honeywell ms2420 User manual
Honeywell
Honeywell MK3480-30B104 - IS3480 QuantumE - Wired Desktop Barcode... User manual
Honeywell
Honeywell YJ HF600 User manual
Honeywell
Honeywell Solaris MS7820 User manual
Honeywell
Honeywell 1900GHD User manual
Honeywell
Honeywell 4800i User manual
Honeywell
Honeywell Genesis 7580G User manual
Honeywell
Honeywell VOYAGER 1200G User manual
Honeywell
Honeywell MS9520 Voyager User manual
Honeywell
Honeywell Voyager 1202G User manual
