HIK VISION DS-2CE59U7T-VPIT3ZF User manual
TURBO HD
U7T Series Dome Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Model
Type I Camera
DS-2CE59U7T-(A)VPIT3ZF
Type II Camera
DS-2CE5AU7T-(A)VPIT3ZF
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or update
the products or procedures described in the manual.
0100001080717
Regulatory Information
FCC Information
Please take attention that changes or modification not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European standards
listed under the Low Voltage Directive 2014/35/EU, the
EMC Directive 2014/30/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed
of as unsorted municipal waste in the
European Union. See the product
documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”.
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings
In the use of the device, you must be in strict
compliance with the electrical safety regulations of the
nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.
The camera is powered by the external DC power
supply (12 VDC, 1 A) which is complied with the LPS,
and the output current of this external DC power
supply must be no more than 6 A.
Do not connect multiple devices to one power adapter
to avoid over-heating or a fire hazard caused by
overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and
then contact the service center.
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
Do not drop the camera or subject it to physical shock.
Do not touch senor modules with fingers.
Do not place the camera in extremely hot, cold (the
operating temperature shall be -40°C to 60°C), dusty or
damp locations, and do not expose it to high
electromagnetic radiation.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp
environment.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Keep the camera away from liquid while in use for non-
water-proof device.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
AC Voltage
1Introduction
1.1 Product Features
The main features are as follows:
High performance CMOS sensor
IR cut filter with auto switch
OSD menu with configurable parameters
Auto white balance
Internal synchronization
SMART IR mode
4 in 1 video output (switchable TVI/AHD/CVI/CVBS)
3-axis adjustment
1.2 Overview
1.2.1 Overview of Type I Camera
Bubble Back Box
Lens Power Cord
Video Cable
Switch
Button
Figure 1-1 Overview of Type I Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
1.2.2 Overview of Type II Camera
Bubble
Lens
Back Box
Power Cord
Switch Button
Video Cable
Figure 1-2 Overview of Type II Camera
Note:
Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.
2Installation
Before you start:
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with your
power output to avoid the damage.
Make sure the wall is strong enough to withstand
three times the weight of the camera and the mount.
If the wall is cement, you need to insert expansion
bolts before you install the camera. If the wall is
wooden, you can use self-tapping screws to secure the
camera.
If the product does not function properly, contact your
dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.
2.1 Ceiling Mounting of Type I Camera
Before you start:
Both wall mounting and ceiling mounting are suitable for
the dome camera. Ceiling mounting will be taken as an
example in this section. You can take steps of ceiling
mounting as a reference for wall mounting.
Steps:
1. Paste the drill template to the celling.
2. Drill screw holes and the cable hole (optional) on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet
to route the cable.
3. Loosen the screws on the bubble of the dome camera
to remove the bubble and the black liner.
4. Attach the back box of type I camera/base plate of
type II camera to the ceiling and secure them with
supplied screws.
Figure 2-2 Attach the Back Box/Base Plate
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement ceiling, expansion bolts are required to
fix the camera. For wooden ceiling, self-tapping
screws are required.
5. Route the cables through the cable hole, or the side
opening.
6. Align the camera with the back box/base plate, and
tighten the screws to secure the camera with the back
box/base plate.
Figure 2-3 Fix the camera to the Ceiling
7. Connect the corresponding cables, such as power cord
and video cable.
8. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to get
an optimum angle.
0° to 355°
0° to 355°
0° to 75°
Figure 2-4 3-Axis Adjustment
9. Fit the black liner back to the camera and tighten the
screws on the bubble of the dome camera to finish
the installation.
2.2 Wall Mounting of Type I Camera
Before you start:
You need to purchase a wall mount first.
Steps:
1. Drill 4 screw holes in the wall according to the holes of
the mount.
2. Attach the mount to the wall by aligning the 4 screw
holes of the mount.
3. Insert supplied expansion screws in the screw holes.
4. Secure the mount with 4 hex nuts and washers.
Figure 2-5 Install Wall Mounting Mount
5. Refer to step 3 of 2.1 Ceiling Mounting of Type I
Camera to remove dome camera’s bubble and the
black liner.
6. Attach the back box/base plate of the dome camera to
the wall mount and secure them with supplied screws.
Figure 2-6 Attach the Base Plate to the Mount
7. Route the cables through the mount.
8. Repeat steps 6 to 9 of the 2.1 Ceiling Mounting of Type
I Camera to complete the installation.
2.3 Ceiling Mounting of Type II Camera
Before you start:
Both wall mounting and ceiling mounting are suitable for
the dome camera. Ceiling mounting will be taken as an
example in this section. And you can take steps of ceiling
mounting as a reference for wall mounting.
Steps:
1. Paste the drill template to the celling.
2. Drill screw holes and the cable hole (optional) on the
ceiling according to the supplied drill template.
Figure 2-7 The Drill Template
Note:
Drill the cable hole (hole A) when adopting the ceiling
outlet to route the cable.
3. Loosen the screws on the bubble of the dome camera
to remove the bubble.
Figure 2-8 Remove the Bubble and the Black Liner
4. Attach the back box of camera to the ceiling and
secure them with supplied screws.
Figure 2-9 Attach the Back Box
Note:
The supplied screw package contains self-tapping
screws, and expansion bolts.
For cement ceiling, expansion bolts are required to
fix the camera. For wooden ceiling, self-tapping
screws are required.
5. Route the cables through the cable hole, or the side
opening.
6. Connect the corresponding cables, such as power
cord, and video cable.
7. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to get
an optimum angle.
0° to 355°
0° to 355°
0° to 75°
Figure 2-10 3-Axis Adjustment
8. Fit the bubble back to the camera.
Figure 2-11 Fit the Black Liner Back
9. Tighten the screws on the bubble of the dome camera
to finish the installation.
Figure 2-12 Finish Installation
2.4 Wall Mounting of Type II Camera
Before you start:
You need to purchase a wall mount first.
Steps:
1. Drill 4 screw holes in the wall according to the holes of
the mount.
2. Attach the mount to the wall by aligning the 4 screw
holes of the mount.
3. Insert supplied expansion screws in the screw holes.
4. Secure the mount with 4 hex nuts and washers.
Figure 2-13 Install Wall Mount
5. Refer to step 3 of 2.3 Ceiling Mounting of Type II
Camera to remove dome camera’s bubble.
6. Attach the back box of the dome camera to the wall
mount, and secure them with supplied screws.
Figure 2-14 Attach the Back Box to the Mount
7. Route the cables through the mount.
8. Repeat steps 6 to 9 of the 2.1 Ceiling Mounting of Type
II Camera to complete the installation.
3Menu Description
Purpose:
Call the menu by clicking the button on the PTZ
Control interface, or call preset No.95.
Steps:
1. Connect the camera with the TVI DVR, and the
monitor, shown as the figure 3-1.
Camera
TVI DVR
Monitor
Figure 3-1 Connection
2. Power on the analog camera, TVI DVR, and the
monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking button, or call
preset No. 95.
MAIN MENU
VIDEO
SETTINGS
FACTORY
DEFAULT
EXIT
EXPOSURE MODE
CONTRAST
SHARPNESS
SATURATION
3DNR
MIRROR
BACK
AGC
EXPOSURE
VIDEO
FORMAT
BACK
EXIT
SAVE & EXIT
WHITE
BALANCE
BRIGHTNESS
SAVE & EXIT
EXIT
SAVE & EXIT
DAY/NIGHT
MODE
BACK
EXIT
SAVE & EXIT
IMAGE
MODE
Figure 3-2 Main Menu Overview
5. Click the direction arrow to control the camera.
This manual suits for next models
4
Table of contents
Other HIK VISION Security Camera manuals
HIK VISION
HIK VISION DS-2CC1181P(N)(-A) User manual
HIK VISION
HIK VISION DS-2DE2C200SCG-E User manual
HIK VISION
HIK VISION DS-2CE16C5T-AVFIR3 TURBO HD User manual
HIK VISION
HIK VISION TVI-AC334-VD4Z User manual
HIK VISION
HIK VISION E-series User manual
HIK VISION
HIK VISION 23 Series User manual
HIK VISION
HIK VISION iDS-TCV300-A6I User manual
HIK VISION
HIK VISION DS-2XC6745G0-IZHS User manual
HIK VISION
HIK VISION TURBO HD DS-2CS58C2T-S/F User manual
HIK VISION
HIK VISION DS-2CD6362F-I User manual
HIK VISION
HIK VISION DS-2DF6336V-AEL User manual
HIK VISION
HIK VISION DS-PDCM15PF-IR User manual
HIK VISION
HIK VISION DS-2XS6A25G0-I/CH20S40/K Operating instructions
HIK VISION
HIK VISION iDS-2CD8A46G0-IZHS User manual
HIK VISION
HIK VISION 4 Inch High Speed Dome User manual
HIK VISION
HIK VISION DS-2CE12KF0T-LFS User manual
HIK VISION
HIK VISION DS-2CD2T27G3E-L User manual
HIK VISION
HIK VISION A15 User manual
HIK VISION
HIK VISION DS-2TD6567T-50H4LX/W User manual
HIK VISION
HIK VISION PanoVu DS-2PT3306IZ-DE3 User manual
