HIK VISION DS-2CD7153 User manual
Network Camera
User Manual
V3.0.0
Hangzhou Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com
Service Tel：+86-400-700-5998
2010-04
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
This manual applies to Network Camera.
This manual may contain several technical incorrect places or printing
errors, and the content is subject to change without notice. The
updates will be added to the new version of this manual. We will readily
improve or update the products or procedures described in the
manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or
reliability of the security or signaling aspects of this product. UL has only
tested for fire, shock or casualty hazards as outlined in UL’s Standard(s)
for Safety, UL60950-1. UL Certification does not cover the performance
or reliability of the security or signaling aspects of this product. UL
MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
User Manual of Network Camera 1
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards
to prevent serious injury or
death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
Warnings：
1. In the use of the product, you must strictly comply with the electrical safety
regulations of the nation and region.
2. Source with DC 12V or AC 24V (Whether supporting AC 24V lies on the specific
camera model) according to the IEC60950－1 standard. Please refer to technical
specifications for more details.
3. Do not connect several devices to one power adapter as an adapter overload
may cause over-heating and can be a fire hazard. If use the POE as the power
supply, please make sure that the POE Switch have the sufficient
power .(Whether supporting PoE power supply lies on the specific camera
model)
4. Please make sure that the plug is firmly inserted into the power socket.
5. When the product is installed on a wall or ceiling, the device should be firmly
fixed.
6. If smoke, odor, or noise rise from the device, turn off the power at once and
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera 2
unplug the power cable, then contact the service center.
7. If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera 3
Notice:
1. Make sure the power supply voltage is correct before using the camera.
2. Do not drop the camera or subject it to physical shock.
3. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean
cloth with a bit of ethanol and wipe it gently. If the camera will not be used for
an extended period of time, put on the lens cap to protect the sensor from dirt.
4. Do not aim the camera at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
5. The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor will not be exposed to the
laser beam.
6. Do not place the camera in extremely hot or cold temperatures (the operating
temperature should be between -10°C~+60°C, dusty or damp locations, and do
not expose it to high electromagnetic radiation.
7. To avoid heat accumulation, good ventilation is required for a proper operating
environment.
8. While shipping, the camera should be packed in its original packing, or packing
of the same texture.
9. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the
equipment should be replaced regularly according to their average life time.
The average time varies because of differences between operating
environment and usage history, so regular checking is recommended for all users.
Please contact with your dealer for more details.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
4
Table of Contents
Chapter 1 Network Camera Connection......................................................1
Chapter 2 Network Access ..............................................................................3
2.1 Access over IE Browser..........................................................................3
2.1.1 Live View.........................................................................................4
2.1.2 Parameters Configuration............................................................7
2.2 Access over Client Software ............................................................. 19
2.2.1 Client Software Installation........................................................ 19
2.2.2 Live View...................................................................................... 21
2.2.3 Sensor Parameters Configuration............................................ 24
Chapter 3 Access over Internet ................................................................... 28
3.1 Access network camera with static IP....................................... 28
3.2 Access network camera with dynamic IP................................. 29
Appendix 1 SADP Introduction..................................................................... 33
Appendix 2 Port Map..................................................................................... 35
Appendix 3 Pin Definition............................................................................... 37
User Manual of Network Camera 1
Chapter 1 Network Camera
Connection
Two methods can be used to connect between network camera and PC, shown as
below:
Fig. 1.1 Cross Line Connection
Fig. 1.2 Direct Line Connection
Before visiting network camera over network, user should acquire its IP address first.
SADP is a software tool which can automatically detect Hikvision’s network device in
the LAN and give the device’s information like IP address, mask, port number,
device serial number, software version, etc., shown as Fig. 1.3.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera 2
Fig.1.3
Select the device, and set its IP address and mask at the same network segment
with the PC.
For the detailed introduction of SADP, please refer to Appendix 1.
Note: The network camera is set with the factory default IP address of “192.0.0.64”,
the port of “8000”, the super user name of “admin” and the password of “12345”.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera 3
Chapter 2 Network Access
After hardware installation, user can view live video and configure parameters for
the network camera, including IP address, subnet mask and port number, etc. The
following two methods can be used to access the camera:
1. View live video and configure parameters over IE browser.
2. View live video and configure parameters over client software.
2.1 Access over IE Browser
Before access to the camera over
IE browser, user should adjust the
security level.
Open the IE browser, and set the
security level to [Low] in [Tools/
InternetOptions/Security/Custom
Level...], and enable Activex
Control and Plug-in directly as
well.
Fig. 2.1.1 Adjust the Security Level
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
User Manual of Network Camera 4
2.1.1 Live View
Figure 2.1.2 Tips of ActiveX Control Installation
Fig. 2.1.3 Install the ActiveX Control
Step 1: Install Active-X Control
and Plug-in.
Input the IP address of the
network camera and press
[Enter], then click the mention
box that pop up.
Step 3:
Step 2:
Click [Run] to install the ActiveX
control.
Input the “Username”
(default: admin), “Password”
(default: 12345) and “Port”
(default: 8000) of the
camera, and then click
[Login].
Fig. 2.1.4 Login Interface
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
Table of contents
Other HIK VISION Security Camera manuals
HIK VISION
HIK VISION A15 User manual
HIK VISION
HIK VISION EPI-5225I-AE User manual
HIK VISION
HIK VISION DS-2CD852F Series User manual
HIK VISION
HIK VISION DS-2CC11D3S-IR User manual
HIK VISION
HIK VISION DS-2CC1197P(N)-A(-C) User manual
HIK VISION
HIK VISION DS-2XM6222FWD-I User manual
HIK VISION
HIK VISION DS-2TD2466-9X User manual
HIK VISION
HIK VISION UD07275B User manual
HIK VISION
HIK VISION DS-2CD6D54G1-ZS/RC User manual
HIK VISION
HIK VISION DS-2TP21B-6AVFW User manual
HIK VISION
HIK VISION UD04828N User manual
HIK VISION
HIK VISION DS-2CD6D44G1H-IZS User manual
HIK VISION
HIK VISION DS-2CD2346G1-l User manual
HIK VISION
HIK VISION EZVIZ C6T MINI 360 PLUS Installation guide
HIK VISION
HIK VISION DS-PDCM15PF-IR User manual
HIK VISION
HIK VISION iDS-2CD7A G0-IZH Series User manual
HIK VISION
HIK VISION PanoVu User manual
HIK VISION
HIK VISION DS-2CE59U7T-VPIT3ZF User manual
HIK VISION
HIK VISION ColorVu DS-2CE DFT-F Series User manual
HIK VISION
HIK VISION Turbo HD DS-2AE5232T-A3 User manual
