HIK VISION DS-2CS54D7T-IRS User manual

TURBO HD

D7T Series Dome Camera

User Manual

UD02018B

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the model listed below.

Model

DS-2CS54D7T-IRS

DS-2CS58D7T-IRS

This manual may contain several technically incorrect

places or printing errors, and the content is subject to

change without notice. The updates will be added to

the new version of this manual. We will readily improve

or update the products or procedures described in the

manual.

0101001060615

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European

standards listed under the EMC Directive 2014/30/EU,

the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”

Warnings: Serious injury or death may occur if any of

the warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the product, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Refer to technical specifications for detailed

information.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 24 V

AC or 12 V DC according to the IEC60950-1 standard.

Refer to technical specifications for detailed

information.

Do not connect several devices to one power adapter

as adapter overload may cause over-heating or a fire

hazard.

Make sure that the plug is firmly connected to the

power socket.

When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cable, and

then contact the service center.

If the product does not work properly, contact your

dealer or the nearest service center. Never attempt to

disassemble the camera yourself. (We shall not

assume any responsibility for problems caused by

unauthorized repair or maintenance.)

Cautions

Make sure the power supply voltage is correct before

using the camera.

Do not drop the camera or subject it to physical

shock.

Do not touch senor modules with fingers. If cleaning

is necessary, use clean cloth with a bit of ethanol and

wipe it gently. If the camera will not be used for an

extended period, replace the lens cap to protect the

sensor from dirt.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

Do not aim the camera at the sun or extra bright

places. Blooming or smearing may occur otherwise

(which is not a malfunction), and affect the

endurance of sensor at the same time.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not place the camera in extremely hot, cold, dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

To avoid heat accumulation, good ventilation is

required for operating environment.

Keep the camera away from liquid while in use.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Improper use or replacement of the battery may

result in hazard of explosion. Replace with the same

or equivalent type only. Dispose of used batteries

according to the instructions provided by the battery

manufacturer.

IntroductionChapter 1

1.1 Product Features

This series of camera adopts high performance CMOS

sensor and advanced circuit board. It features high

resolution, low distortion, and low noise, etc. It is

suitable for surveillance system, and image process

system.

The main features are as follows:

High performance CMOS sensor

1080p resolution

Auto white balance

Auto electronic shutter

Auto gain control (AGC)

True WDR

IR cut filter

Internal 3-axis adjustment

1.2 Overview

Figure 1. 1 Overview of Dome Camera

Power Cable (12 V DC)

Video Cable

Audio Cable

Video

Audio Power (12 V DC)

GND

Model I

Model II

Figure 1. 2 Power Cable and Video Cable

InstallationChapter 2

2.1 Installation Preparation

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with

your power output to avoid damage.

Make sure the wall is strong enough to withstand

three times the weight of the camera and the

mounting bracket.

If the wall is cement l, you need to insert expansion

bolts before you install the camera. If the wall is

wooden, you can use self-tapping screws to secure

the camera.

If the product does not function properly, contact

your dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

2.2 Ceiling Mounting

Steps:

1. Stick the dill template to the ceiling.

2. Drill the screw holes, and the cable hole (optional)

in the ceiling according to the drill template.

Note:

Cable hole is required when you adopts ceiling outlet to

route the cable.

Figure 2. 1 Drill Template

3. Loosen the torx screws to remove the upper cover

from the device.

Figure 2. 2 Remove the Upper Cover

4. Fix the mounting base to the ceiling with the

supplied screws.

Note:

In the supplied screw package, both self-tapping

screws and expansion blots are contained.

If the wall is cement, expansion blots are required

to fix the camera. If the wall is wooden,

self-tapping screws are required.

Figure 2. 3 Fix the Mounting Base

5. Align the supplied adjusting tool to the small hole

on the camera, and push it to get it fixed.

Figure 2. 4 Fix the Mounting Base

6. Loosen the adjustable screw to adjust the pan angle

(±30°), the tilting angle (0°to 85°), and the rotation

angle (±180°) with the adjusting tool, then tighten

the adjustable screws.

Note:

Before adjusting the surveillance angle, you need to

power on the camera first to check whether the image

on the monitor is gotten from the optimum angle.

Figure 2. 5 3-axis Adjustment

7. Install the upper cover back by tightening the torx

screws.

Figure 2. 6 Install the Upper Cover

Note:

The camera is in optimum surveillance angle by

default. Slightly adjust the pan tilting angle

according to the actual environment.

The upper cover should be installed before having

the live view.

Menu DescriptionChapter 3

Two methods are available to call the menu. This

section takes the method b) as the example to state the

menu operation.

a) Call the menu and adjust the camera parameters

with a coaxial camera controller (purchase

separately).

b) Call the menu with supported TVI DVR by clicking

button on the PTZ interface, or by calling preset

No. 95.

Camera

TVI DVR

Monitor

Figure 3. 1 Connection

Steps:

1. After the connection is done, power on the analog

camera, TVI DVR, and monitor to view the image on

the monitor.

2. Click PTZ Control to enter the PTZ Control Interface.

3. Call the camera menu by clicking button, or call

preset No. 95.

4. Click up/down direction button to select the item,

click Iris + to confirm the selection, and click

left/right direction button to adjust the value of the

selected item.

MAIN MENU

AE WB DAY

&NIGHT

VIDEO

SETTING RESET

SAVE

&EXIT

BRIGHTNESS

EXPOSURE

MODE

GAIN

ATW

MWB

COLOR

B/W

CONTRAST

SHARPNESS

COLOR

GAIN

DNR

MIRROR

SMART

FORMAT

SETUP

Figure 3. 2 Main Menu Overview

3.1 Format

Move the cursor to FORMAT, and click Iris+ to enter the

FORMAT sub menu. You can set the format as NTSC or

PAL.

3.2 Main Menu

3.2.1 AE (Auto Exposure)

AE describes the brightness-related parameters. You

can adjust the image brightness by the BRIGHTNESS,

EXPOSURE MODE, and GAIN in different light

conditions.

EXPOSURE

BRIGHTNESS

EXPOSUREMODE

GAIN

RETURN

BLC

MIDDLE

Figure 3. 3 AE

BRIGHTNESS

Brightness refers to the brightness of the image. You

can set the brightness value from 1 to 10 to darken or

brighten the image. The higher the value, the brighter

the image is.

EXPOSURE MODE

You can set AE mode as GLOBAL, BLC, and WDR.

GLOBAL

GLOBAL refers to the normal exposure mode which

adjusts the situations including unusual lighting

distribution, variations, non-standard processing, or

under other exposure conditions to get an optimum

image.

BLC (Backlight Compensation)

BLC (Backlight Compensation) compensates light to the

object in the front to make it clear, but this causes the

over-exposure of the background where the light is

strong.

When BLC is selected as the exposure mode, the BLC

level can be adjusted from 0 to 8.

WDR (Wide Dynamic Range)

The wide dynamic range helps the camera provide clear

images even under backlight circumstances. WDR

balances the brightness level of the whole image and

provides clear images with details.

GAIN

It optimizes the clarity of the image in poor light

conditions. The GAIN level can be set as HIGH, MIDDLE,

or LOW. Select OFF to disable the GAIN function.

Note:

The noise will be amplified when the GAIN is on.

3.2.2 WB (White Balance)

White balance, the white rendition function of the

camera, is to adjust the color temperature according to

the environment. It can remove unrealistic color casts in

the image. You can set WB mode as ATW, or MWB.

ATW

Under ATW mode, white balance is being adjusted

automatically according to the color temperature of the

scene illumination.

MWB

You can set the R GAIN/B GAIN value from 0 to 255 to

adjust the shades of red/blue color of the image.

MODE

R GAIN

BGAIN

RETURN

MWB

Figure 3. 4 MWB Mode

3.2.3 DAY-NIGHT

Color, B/W, and SMART are selectable for DAY and

NIGHT switches.

COLOR

The image is colored in day mode all the time.

B/W

The image is black and white all the time, and the IR

LED turns on in the low-light conditions.

SMART

You can turn on/off the INFRARED and set the value of

SMART IR in this menu.

DAY/NIGHT

MODE

INFRARED

SMART IR

DAY TO NIGHT

NIGHT TO DAY

RETURN

SMART

OPEN

Figure 3. 5 Day & Night

INFRARED

You can turn on/off the IR LED to meet the

requirements of different circumstances.

SMART IR

The Smart IR function is used to adjust the light to its

most suitable intensity, and to prevent the image from

over exposure. The SMART IR value can be adjusted

from 0 to 3. The higher the value the more obvious

effects are, and it is disabled when the value is 0.

DAY TO NIGHT

Set the value from 1 to 10. The higher the value, the

earlier the color status switches to B/W status.

NIGHT TO DAY

Set the value from 1 to 10. The higher the value, the

earlier the B/W status switches to color status.

3.2.4 VIDEO SETTING

Move the cursor to VIDEO SETTING and click Iris+ to

enter the submenu. CONTRAST, SHARPNESS, COLOR

GAIN, DNR, and MIRROR are adjustable.

VIDEO SETTING

CONTRAST

SHARPNESS

COLOR GAIN

DNR

MIRROR

RETURN

DEFAULT

Figure 3. 6 Video Setting

CONTRAST

This feature enhances the difference in color and light

between parts of an image. You can set the CONTRAST

value from 1 to 10.

SHARPNESS

Sharpness determines the amount of detail an imaging

system can reproduce. You can set the SHARPNESS

value from 1 to 10.

COLOR GAIN

Adjust this feature to change the saturation of the color.

The value ranges from 1 to 10.

DNR (Digital Noise Reduction)

The DNR function can decrease the noise effect,

especially when capturing moving images in low light

conditions and delivering more accurate and sharp

image quality. You can set the DNR value from 1 to 10.

MIRROR

DEFAULT, H, V, and HV are selectable for mirror.

DEFAULT: The mirror function is disabled.

H: The image flips 180°horizontally.

V: The image flips 180°vertically.

HV: The image flips 180°both horizontally and

vertically.

3.2.5 RESET

Reset all the settings to the default.

3.2.6 SAVE & EXIT

Move the cursor to SAVE & EXIT and click Iris+ to save

the setting and exit the menu.

This manual suits for next models

Table of contents

Other HIK VISION Security Camera manuals

HIK VISION

HIK VISION DS-2CE16COT-IRF User manual

HIK VISION

HIK VISION DS-2CC5181P-VP User manual

HIK VISION

HIK VISION DS-2DF1-614X/604X User manual

HIK VISION

HIK VISION DS-2DE4225W-DE User manual

HIK VISION

HIK VISION NSC-4A220-PTZIR User manual

HIK VISION

HIK VISION AE-VC136T User manual

HIK VISION

HIK VISION DS-2CD2332-I User manual

HIK VISION

HIK VISION DS-2CD8153F-EWI User manual

HIK VISION

HIK VISION DS-2DE2A404IW-DE3/W User manual

HIK VISION

HIK VISION DS-2CD883F-EW series User manual

HIK VISION

HIK VISION DS-2TD6267-75C4L/WY User manual

HIK VISION

HIK VISION DS-2CD3D26G2T-IZHSY User manual

HIK VISION

HIK VISION Turbo HD D0T Series User manual

HIK VISION

HIK VISION DS-2DF5220S User manual

HIK VISION

HIK VISION DS-2CE16D(F)7T-IT3Z User manual

HIK VISION

HIK VISION NETWORK CAMERA User manual

HIK VISION

HIK VISION I0M1000 User manual

HIK VISION

HIK VISION HiLook IK-4142B-MH/W User manual

HIK VISION

HIK VISION DS-2CD6924G0-IHS User manual

HIK VISION

HIK VISION DS-2CC12A1PN-AVFIR3 User manual

HIK VISION

HIK VISION DS-2CE10HFT-F User manual

HIK VISION

HIK VISION DS-2CC 2D9T Series User manual

HIK VISION

HIK VISION HWI-T220H User manual

HIK VISION

HIK VISION DS-2CE12H0T-PIRL User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications