Heath Zenith Wireless Push Button Accessory SL-6190... User manual

Wireless Push Button

Accessory

The Heath®/Zenith Wireless Push Button Acces-

sory works with existing Heath®/Zenith jumper or

dip switch systems.

• Battery powered push button - No wires to run.

• 128selectablecodesallowmorethanonechime

system in the same house.

SL-6190 Series and SL-6290 Series

(Style may vary from illustration)

-2- 595-5507-11

2. Setthepush button jumpers to match the chime receiver

code. See “Code and Tune Setting” section.

1. Install alkaline type A23 12 volt push

button battery. Remove back of case

by pushing in tab on bottom with a

small screwdriver. Make sure battery is

oriented properly (see page 5).

4. Mount push button.

Use either screws or double sided tape

to mount push button.

To mount with screws, remove back of

case by pushing in tab on bottom with a

small screwdriver.

Attach back of case to door jamb or wall.

Snap front of push button on.

When attaching push button using double

sided tape, make sure the surface of the door jamb or wall is

clean.

3. Test range. Temporarily position push button where you want

it mounted. Press push button to verify chime and push button

work properly. If chime does not sound, see Troubleshooting.

-3-

595-5507-11

Code and Tune Settings

Code Settings

Note: Most installations will not require you to change any

jumpers on your chime and push button.

WARNING: Disconnect chime unit from power source before

opening code access door. Close door and replace screw

before reconnecting to power.

The push button and chime communicate by using a code that

can be changed by removing and/or adding jumpers on both the

push button and chime. The code is factory set; however, there

are 128 selectable codes that allow you to expand your system

and prevent outside interference. Other wireless products may

cause interference and the system may not function properly.

Follow the instructions below for setting a new code.

1. Unplug wireless chime (if applicable).

2. Open the cases and locate the jumpers on both the push button

and chime (See illustration on page 5).

3. The push button and chime both have eight different jumper

locations.The jumper positions 1 through 7 are used for setting

the code.

4. To change the code, add and/or remove jumpers as needed. It

is recommended to only change one jumper at a time and then

check to see if system is functioning properly. Note: Jumpers

in positions 1 through 7 must be exactly the same for both the

push button and chime for this system to function.

-4- 595-5507-11

Tune Settings

Your Heath®/Zenith wireless chime has different selectable tunes:

Ding (one note), Ding-Dong (two note), or Westminster (eight

note) (Available on selected Heath®/Zenith chimes). The factory

setting is for the Ding-Dong tune (or Westminster, when available).

This tune can be changed by following the instructions below.

• Ding (one note tune)

Push button: Add a jumper to location 8.

• Ding-Dong (two note tune)

Push button: Remove jumper from location 8.

Chime: Remove jumper from location 8.

• Westminster (Eight note tune) (Available on selected Heath®/

Zenith chimes)

Push button: Remove jumper from location 8.

Chime: Add a jumper to location 8.

Note: All models have both front and back door tune capabilities.

You may purchase any Heath®/Zenith wireless push button for a

second entrance.We recommend the back door use the Ding tune

and the front door use the Ding-Dong tune (or Westminster tune,

available on selected Heath®/Zenith chimes).Models that include

two push buttons will come factory set for front and back doors.

Decals on the rear of the push button will indicate its setting.

-5-

595-5507-11

Push Button Battery Replacement

Install an alkaline type A23 12 Volt

battery. See diagram inside push but-

ton for correct battery orientation.

Remove

screw to open

access door

Tune Setting (Not

used on all models)

Back of

Chime

12345678

Inside Push

Button

* Code Settings

1-7 Must Match

Both Push Button

and Chime

Tune

Setting

Note: Some models might require

the use of tweezers to remove and

replace the jumpers.

-6- 595-5507-11

Troubleshooting

Chime does not sound:

• Make sure push button and chime codes are the same (See pages 3,

4, and 5).

• Check orientation of push button battery (See page 5).

• Check charge of push button and chime batteries (if applicable), replace

if necessary.

Batteries seem OK, but the chime does not work when installed:

• Do not mount chime or push button on metal or near metal studs.This

reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood

shims to move chime or push button off metal surface.

• Concrete ﬂoors may reduce range. Move chime away from ﬂoor.

• Try locating chime closer to push button.

The range of the wireless chime can vary with location, temperature and

battery condition.

-7-

595-5507-11

HeathCoLLCreservestherighttodiscontinueandtochangespeciﬁcations

at any time without notice without incurring any obligation to incorporate

new features in previously sold products.

Regulatory Information

This device complies with Part 15 of the FCC Rules and RSS-210 of

Industry Canada. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause

undesired operation.

The user is cautioned that changes or modiﬁcations not expressly ap-

proved by the party responsible for regulatory compliance could void the

user’s authority to operate the equipment.

Technical Service

Please call 1-800-858-8501 (English speaking only) for as-

sistance before returning product to store.

If you experience a problem, follow this guide.You may also want to visit

our Web site at: www.hzsupport.com. If the problem persists, call* for

assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F).You may

also write* to:

HeathCo LLC

P.O. Box 90004, Bowling Green, KY 42102-9004

ATTN: Technical Service

* If contacting Technical Service, please have the following information

available: Model Number, Date of Purchase, and Place of Purchase.

No Service Parts Available for this Product

-8- 595-5507-11

FIVE YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you speciﬁc legal rights.You may also

have other rights which vary from state to state or province to province.

For a period of ﬁve years from the date of purchase, any malfunction caused by

factory defective parts or workmanship will be corrected at no charge to you.To

obtain a refund or a replacement, return the product to the place of purchase.

Not Covered - Repair service, adjustment and calibration due to misuse,

abuse or negligence, and expendable items are not covered by this warranty.

Unauthorized service or modiﬁcation of the product or of any furnished com-

ponent will void this warranty in its entirety. This warranty does not include

reimbursement for inconvenience, installation, setup time, loss of use, or

unauthorized service.

This warranty covers only HeathCo LLC assembled products and is not

extended to other equipment and components that a customer uses in con-

junction with our products.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION

ORCONDITIONOFMERCHANTABILITYORTHATTHEPRODUCTSAREFIT

FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF

ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

REPAIR OR REPLACEMENT SHALL BETHE SOLE REMEDY OFTHE CUS-

TOMER ANDTHERE SHALL BE NO LIABILITY ONTHE PART OF HEATHCO

LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS

ORPROFITS,WHETHERORNOTFORESEEABLE.Somestatesorprovinces

do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you. Please keep your

dated sales receipt, it is required for all warranty requests.

-9-

595-5507-11

Accesorio de pulsador

inalámbrico

El accesorio de pulsador inalámbrico Heath®/Ze-

nith funciona con el puente Heath®/Zenith o con

los sistemas de interruptores.

• Pulsador alimentado con pila – No se necesitan

alambres.

• Los 128 códigos elegibles permiten más de un

sistema de campanas en la misma casa.

Serie SL-6190 y Serie SL-6290

(El estilo puede variar de la ilustración)

-10- 595-5507-11

2. Fije los puentes del pulsador de acuerdo al código del

receptor de campana. Vea la sección de “Programaciones

del código y del tono”.

1. Instalar pila alcalina de botón tipo A23

de 12 voltios. Extraer la parte posterior

de la caja presionando la aleta en el

botón con un destornillador pequeño.

Asegurarse que la pila esté orientada

correctamente (ver la página 13).

4. Instale el pulsador.

Use ya sean tornillos o cinta adhesiva por

ambas caras para instalar el pulsador.

Para montar con tornillos, quite la parte de

atrás de la caja empujando hacia adentro

la lengüeta de abajo con un destornillador

pequeño y girando la cuchilla.

Coloque la parte de atrás de la caja contra

la jamba o la pared. Encaje a presión la parte frontal del pulsador.

Cuando ﬁje el pulsador usando cinta adhesiva por ambas caras,

asegúrese que la superﬁcie de la pared o la del batiente de la

puerta estén limpias.

Pruebe el alcance. Ponga provisionalmente el pulsador en la

posición donde lo quiera instalar. Presione el pulsador para

veriﬁcar que la campanay el pulsador funcionen apropiada-

mente. Si la campana no suena, vea Análisis de Averías.

This manual suits for next models

Table of contents

Languages:

Other Heath Zenith Accessories manuals

Heath Zenith

Heath Zenith 7307 User manual

Heath Zenith

Heath Zenith 598-1215-01 User manual

Heath Zenith

Heath Zenith SL-6143 User manual

Heath Zenith

Heath Zenith 598-1109-06 User manual

Heath Zenith

Heath Zenith SL-6168 User manual

Heath Zenith

Heath Zenith Notifi elite User manual

Heath Zenith

Heath Zenith 121AC User manual

Heath Zenith

Heath Zenith 7311 User manual

Heath Zenith

Heath Zenith 7868 User manual

Heath Zenith

Heath Zenith 6180 Series User manual

Heath Zenith

Heath Zenith 7797 User manual

Heath Zenith

Heath Zenith 7776 User manual

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 User manual

Heath Zenith

Heath Zenith Notifi Elite User manual

Heath Zenith

Heath Zenith 595-5684-09 User manual

Heath Zenith

Heath Zenith SL-6153 User manual

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 User manual

Heath Zenith

Heath Zenith Wireless Mechanical Chime 598-1123-02 User manual

Heath Zenith

Heath Zenith SL-6155 Series User manual

Heath Zenith

Heath Zenith Single Entrance Chime 23/M User manual

Heath Zenith

Heath Zenith Replacement Motion Sensor SL-5407 User manual

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 User manual

Heath Zenith

Heath Zenith HZ-1802-BK-A User manual

Heath Zenith

Heath Zenith 7306 User manual

Popular Accessories manuals by other brands

Hillco

Hillco 2810 Operator's manual

Siemens

Siemens QSA2700D Basic documentation

Contours

Contours ZY024 manual

Saivod

Saivod VS621 manual

Virtuox

Virtuox VirtuCLEAN 2.0 user manual

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS user manual

Z-Wave

Z-Wave HSD-200Z user manual

turck

turck FMX-IM-2UPLI63FX quick start guide

Decagon Devices

Decagon Devices 10HS manual

UPPAbaby

UPPAbaby Cup Holder user manual

Elko

Elko SmartSensor Leakage Wireless manual

Grizzly

Grizzly H8371 instructions

Panasonic

Panasonic HG-T Series user manual

IFM Electronic

IFM Electronic Efector 250 Series Brief instructions

DigiDesign

DigiDesign 888/24 I/O installation guide

PROZIS

PROZIS QUAY user manual

patagonia

patagonia PSI Vest user manual

SFC Energy

SFC Energy EFOY GO! manual