HAMPTON BAY Waterton II User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and

material present at time of shipment from the factory for a lifetime after the date of

purchase by the original purchaser. The retailer also warrants that all other fan parts,

excluding any glass or plexiglass blades, to be free from defects in workmanship and

material at the time of shipment from the factory for a period of one year after the date

of purchase by the original purchaser. We agree to correct such defects without charge

or at our option replace with a comparable or superior model if the product is returned

to the retailer. To obtain warranty service, you must present a copy of the receipt as

proof of purchase. All costs of removing and reinstalling the product are your

responsibility. Damage to any part such as by accident or misuse or improper

installation or by affixing any accessories, is not covered by this warranty. Because of

varying climatic conditions in the United States this warranty does not cover any

changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling.

Brass finishes of this type give their longest useful life when protected from varying

weather conditions. A certain amount of wobble is normal and should not be

considered a defect. Servicing performed by unauthorized persons shall render the

warranty invalid. There is no other express warranty. The retailer hereby disclaims

any and all warranties, including but not limited to. Those of merchantability and

fitness for a particular purpose to the extent permitted by law. The duration of any

implied warranty which cannot be disclaimed is limited to the time period as specified

in the express warranty. Some states do not allow limitation on how long an implied

warranty lasts, so the above limitation may not apply to you. The retailer shall not be

liable for incidental, consequential, or special damages arising out of or in

connection with product use or performance except as may otherwise be accorded by

law. Some states do not allow the exclusion of incidental or consequential damages,

so the above exclusion or limitation may not apply to you. This warranty gives specific

legal rights, and you may also have other rights which vary from state to state. This

warranty supersedes all prior warranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

553-663

11289

792145350941

Safety Rules............................................................................................................

Unpacking Your Fan ..................................................................................................

Installing Your Fan ....................................................................................................

Installing the Light Kit................................................................................................

....................................................................................................

Care of You r Fan ......................................................................................................

Troubleshooting .......................................................................................................

Specifications ..........................................................................................................

Operating Your Fan

10.

11.

12.

13.

Table of Contents

1. Safety Rules

1.To reduce the risk of electric shock, insure electricity has been

turned off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code and local electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not

use this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of personal injury, use only the two

steel screws (and lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes commonly used for

the support of lighting fixtures are not acceptable for fan support

and may need to be replaced, consult a qualified electrician if in

doubt.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making electrical connections, spliced conductors should

be turned upward and pushed carefully up into the outlet box.

The wires should be spread apart with the grounded conductor

and the equipment-grounding conductor on one side of the outlet

box.

12. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for

use with the model fan you are installing. Switches must be UL

General Use Switches. Refer to the Instructions packaged with

the light kits and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLETBOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted

and capable of reliably supporting a minimum of 50 pounds. Use

only UL Listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance

from the trailing edge of the blades to the floor.

7.Do not operate the reverse switch while the fan blades are in

motion. The fan must be turned off and the blades stopped before

reversing the blades direction.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING ASSEMBLY

OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH OF

THE BLADES.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items;

1. Fan blades (5)

2. Canopy assembly

4. Coupling cover

5. Fan motor assembly

6. Blade arms (5)

Ball/downrod assembly

7. Mounting plate

8. Light kit assembly

9. Glass shades

10. 6

11.

12.

13. Balancing kit

(3)

0Watt intermediate bulbs (3)

Pull chain and fob (2)

Extra plastic plug

14. Loose parts bag containing:

a. Blade attachment hardware

()

b. Mounting hardware

( 3 plastic wire connectors)

16 screws

WARNING

DO NOT INSTALL OR USE FAN

IF ANY PART IS DAMAGEDOR MISSING.

CALL TOLL FREE 1-877-898-1881

Unpacking Your Fan 2.

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustable wrench, step

ladder, and wire cutters.

Mounting Options

If there isn't an existing UL listed

mounting box, then read the following

instructions. Disconnect the power by

removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and building materials. The

outlet box and its support must be able

to fully support the moving weight of the

fan (at least 50 lbs). Do not use plastic

outlet boxes.

Figures 1,2 and 3 are examples of

different ways to mount the outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need

an installation hanger bar as shown in

Figure 4 (available at your Hampton Bay

Retailer).

Outlet box

Figure 1

Figure 2

Figure 4

3. Installing Your Fan

Provide strong support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Figure 3

Angled ceiling

maximum

18 angle

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning

the cover counter clockwise.(Fig. 5)

Step 2. Remove the hanger bracket from

the canopy by loosening the two screws

on the bottom of the hanging bracket

from the screw head and turning

the canopy counter clockwise.(Fig, 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling

hanger bracket as shown in Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 5. Remove the hanger pin, lock pin

and set screws from the top of the motor

assembly.

Step 6. Route wires exiting from the top of

the fan motor through the collar cover,

canopy cover, canopy and then through

the ball / downrod. (Fig. 7)

half turn

WARNING

FAILURE TOPROPERLY INSTALL LOCKING PIN AS

NOTED IN STEP 7 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Step 8. Tighten two set screws at top of the

fan motor collar firmly. (Fig. 7)

Step 9. Place the downrod ball into the

hanger bracket socket.

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top

of the motor housing (Fig.7). Carefully

insert the hanger pin through the holes in

the collar and downrod. Be careful not to

jam the pin against the wiring inside the

downrod. Insert the locking pin through the

hole near the end of the hanger pin until it

snaps into its locked position, as noted in

the circle inset of Fig. 7.

Figure 5

Hanger

bracket

Hanger

bracket

Ceiling

canopy

Canopy

cover

Mounting

screws

(supplied with

electrical box)

Hook

UL Listed

electrial

box

Figure 6

120V Wires

Washers

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 7

Hanger pin

Locking pin Collar cover

Canopy

cover

CAUTION

REMOVE 5 RUBBER PACKING MOUNTSAND

DISCARD BEFORE INSTALLATION.

Making the Electrical

Connections

Remember to disconnect the power.

Follow the steps below to connect the fan to your household

wiring. Use the wire connecting nuts supplied with your fan.

Secure the connectors with electrical tape. Make sure there

are no loose strands or connections.

Step 1 Connect the fan supply (black) wire and light supply

(blue) wire to the black household supply wire as shown in

Figure 8.

Step 2. Connect the neutral fan (white) wire to the white

netura household wire.

Step 3 Connect the fan ground wire (green) to the household

ground wire.

Step 4 After connecting the wires, spread them apart so that

the green and white wires are on one side of the outlet box

and the black and the blue wires are on the other side.

Step 5 Turn the connecting nuts upward and push the wiring

into the outlet box.

Figures 9 and 10 illustrate the wiring connections for the

optional wall control (available at your Hampton Bay Retailer,

the wire color out of the wall control may vary, see wall

control's installation manual for correct wire connections.)

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITEWHITE

BLACK

BLUE

GREEN

WHITE

BLUE

BLACK WHITE

Figure 8

Diagram indicates optional light kit wiring.

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 9

Diagram indicates optional light kit wiring.

Light Switch

WHITE

BLUE

BLACK WHITE

NOTE

LIGHT KITS ARE AVAILABLE AT YOUR

HAMPTON BAY RETAILER. THE FAN IS

ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER

PERSONAL INJURY. MOUNT FAN ONLY ON AN OUTLET BOX OR

SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE

THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

Diagram indicates optional light kit wiring.

Light

Fan

WHITE

BLUE

BLACK WHITE

Figure 11

Outlet box

Hanger

bracket

Canopy

cover

Screws

Finishing the Installation

Step 1. Tuck connections neatly into

ceiling outlet box.

Step 2. Slide the canopy up to ceiling and

over the 2 screws on the hanger bracket.

Rotate canopy clockwise. Next, while

holding the canopy with one hand, slide

the canopy cover over the screws and

rotate clockwise until tight. Note: adjust

the canopy screws as necessary until the

canopy and canopy cover are snug. (Fig.

11)

WARNING

Make sure the notch on the hanging

bracket properly sits in the groove in

the hanger ball before attaching the

canopy to the bracket by turning the

housing until it drops into place.

Rubber

washer

Blade

arm

Figure 12

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach blades to blade arms using

three screws and rubber washers as shown

in Figure 12. Start a screw into the arm, do

not tighten. Repeat for the 2 remaining

screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade

is straight.

Step 3 Fasten the blade arms to the motor

by inserting the tab from the blade arms to

the slot in the bottom motor housing, then

tighten the two screws and washers already

installed in the blade arms (Figure 13).

Step 4 Install an optional light kit if you

wish. Follow the instructions included with

the kit. Figure 13

Motor

Blade arm

Slot

Tab

All blades are grouped by weight.

Because natural woods very in density,

the fan may wobble even though the

blades are weighed equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade bracket

screws are secure.

2. Most fan wobbling problems are

caused when blade levels are unequal.

Check this level by selecting a point on

the ceiling above the tip of one of the

blades. Measure this distance as shown

in Figure 14. Rotate the fan until the

next blade is positioned for

measurement. Repeat for each blade.

The distance should be equal

within 1/8".

deviation

3. Use the enclosed Blade Balancing Kit

if the blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY 286-780 User manual

HAMPTON BAY

HAMPTON BAY TITAN 52 User manual

HAMPTON BAY

HAMPTON BAY Colonial Bamboo User manual

HAMPTON BAY

HAMPTON BAY MADISON AK30A-BN User manual

HAMPTON BAY

HAMPTON BAY GAZEBO III YG988-BN User manual

HAMPTON BAY

HAMPTON BAY WELLTON 60 AM588A-BN User manual

HAMPTON BAY

HAMPTON BAY Palm Beach II User manual

HAMPTON BAY

HAMPTON BAY HAWKINS YG204-BN User manual

HAMPTON BAY

HAMPTON BAY CF556A-H26 User manual

HAMPTON BAY

HAMPTON BAY COSTA MESA User manual

HAMPTON BAY

HAMPTON BAY WDF9-2 User manual

HAMPTON BAY

HAMPTON BAY FE30-DM User manual

HAMPTON BAY

HAMPTON BAY Trusseau User manual

HAMPTON BAY

HAMPTON BAY TIPTON II 52 INCH User manual

HAMPTON BAY

HAMPTON BAY Middleton 42 inch User manual

HAMPTON BAY

HAMPTON BAY 290-286 User manual

HAMPTON BAY

HAMPTON BAY 68" Enchantment User manual

HAMPTON BAY

HAMPTON BAY Bercello Estates II User manual

HAMPTON BAY

HAMPTON BAY Clarington 503 837 User manual

HAMPTON BAY

HAMPTON BAY ESALA AK395-CB User manual

HAMPTON BAY

HAMPTON BAY Palisades User manual

HAMPTON BAY

HAMPTON BAY YG188M-NI User manual

HAMPTON BAY

HAMPTON BAY Campbell II User manual

HAMPTON BAY

HAMPTON BAY 51750 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual