HAMPTON BAY 286-780 User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and

material present at time of shipment from the factory for a lifetime after the date of

purchase by the original purchaser. The retailer also warrants that all other fan parts,

excluding any glass or plexiglass blades, to be free from defects in workmanship and

material at thetime of shipmentfrom the factoryfor a periodof one yearafter the date

of purchase by the original purchaser. We agree to correct such defects without

charge or at our option replace with a comparable or superior model if the product is

returned to the retailer. To obtain warranty service, you must present a copy of the

receipt as proof of purchase. All costs of removing and reinstalling the product are

your responsibility. Damage to any part such as by accident or misuse or improper

installation or by affixing any accessories, is not covered by this warranty. Because

of varying climatic conditions in the United States this warranty does not cover any

changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling.

Brass finishes of this type give their longest useful life when protected from varying

weather conditions. A certain amount of wobble is normal and should not be

considered a defect. Servicing performed by unauthorized persons shall render the

warranty invalid. There is no other express warranty. The retailer hereby

disclaims any and all warranties, including but not limited to. Those of

merchantability and fitness for a particular purpose to the extent permitted by

law. The duration of any implied warranty which cannot be disclaimed is limited to

the time period as specified in the express warranty. Some states do not allow

limitation on how long an implied warranty lasts, so the above limitation may not

apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance

except as may otherwise be accorded by law. Some states do not allow the

exclusion of incidental or consequential damages, so the above exclusion or

limitation may not apply to you. This warranty gives specific legal rights, and you

may also have other rights which vary from state to state. This warranty supersedes

all prior warranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

286-780

219032

792145330783

Safety Rules..........................................................................................................................

Unpacking Your Fan..............................................................................................................

Installing Your Fan................................................................................................................

Installing the Light Kit..........................................................................................................

Operating Your transmitter....................................................................................................

Care of Your Fan...................................................................................................................

Troubleshooting...................................................................................................................

Specifications......................................................................................................................

Table of Contents

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breaker or fuse boxbefore beginning.

2. Allwiring must bein accordance withthe National ElectricalCode and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fan speed control device.

4. WARNING: To reduce the risk of personal injury, use only the two

steel screws (and lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may

need to bereplaced, consult a qualified electrician ifin doubt.

8. Avoid placing objectsin the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for use

with the model fan you are installing. Switches must be UL General

Use Switches. Refer to the Instructions packaged with the light kits

and switches forproper assembly.

WARNING

TO REDUCETHE RISK OF FIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TOOUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades to the floor.

7. Do not operate the reverse switch while the fan blades are in motion.

The fan must be turned off and the blades stopped before reversing the

blades direction.

WARNING

TO REDUCETHE RISK OF PERSONAL INJURY, DO NOTBEND THE

BLADE ARMS(ALSO REFERRED TO ASBRACKETS) DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

2. Unpacking Your Fan

Unpack your fanand check the contents. You should havethe following items:

2. Canopy

Set of blades(5)

assembly

Ball/downrod assembly (1)

& extra downrod(1)

Collar cover

Fan motor assembly

6. Set ofblades arms (5)

7. Light plate

Glass shade

Receiver+6 wire nuts

Transmitter+holder+2 mounting screws

Bulbs (3)

12. Balancing kit

10.

11.

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED ORMISSING.

CALL TOLLFREE 1-877-898-1881

ONON

LIGHT / DIMMER

LO MED HI

FAN OFF

13. Loose partsbag containing:

a. Blade attachmenthardware

(16 screws, 16rubber washers)

b. Mounting hardware

(3 plastic wireconnectors)

c. Light kithardware

(1 screw)

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing ULlisted mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourHampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

20 angle

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps belowto hang your fan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise.(Fig.5)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket

from the screw head and turning the canopy

counter clockwise.(Fig, 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shownin Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided withyour outlet box.

Step 5.Remove the hanger pin, locking pin

and set screws from the top of the motor

assembly.

Step 6. Route wires exiting from the top of

the fan motor through the collar cover,

canopy cover, canopy and then through the

ball / downrod.(Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with theholes in the collar on top of

a half turn

Step 8. Tighten two set screws on top of the

fan motor firmly (Figure 7)

Step 9. Place the downrod ball into the hanger

bracket socket.

CHANGING THE DOWNROD (OPTIONAL)

NOTE: Your fan comes with a 4" downrod

attached to the hanger ball. In addition you

have been provided with a 6" downrod to use if

desired. If you choose to use the 6" downrod,

perform the followingsteps:

1. Remove the hanger ball from the 4"

downrod by loosening the set screw at the

top of the downrod which holds the hanger

ball to thedownrod.

2. Slide the hanger ball down the downrod and

remove the supportpin.

WARNING

FAILURETO PROPERLY INSTALL LOCKINGPIN

AS NOTED INSTEP 7 COULD RESULT IN FAN

LOOSENING ANDPOSSIBLYFALLING.

the motor housing (Fig.7). Carefully insert the

hanger pin through the holes in the collar and

downrod. Be carefulnot to jam the pin against

the wiring inside the downrod. Insert the

locking pin through the hole near the end of

the hanger pin until it snaps into its locked

position, as notedin the circle inset of Fig. 7.

Mounting

screws

(supplied with

electrical box)

Tab

Ceiling

mounting

plate

UL Listed

electrical

box

Figure 6 120V Wires

Washers

3. Insert the support pin in the holes at the

top of the 6" downrod and slide the

hanger ball up the 6" downrod. Make

sure the support pin is properly seated in

the grooves inthe top of the hanger ball.

4. Tightenthe set screw firmly.

Figure 5

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

Make the Electric Connections

WARNING: To avoid possible electrical

shock, be sureelectricity is turned off at the

main fuse boxbefore wiring.

NOTE: This remote control unit is

equipped with 16 code combinations to

prevent possible interference from or to

other remote units. The frequency switches

on your receiver and transmitter have been

preset at the factory. Please recheck to

make sure the switches on transmitter and

receiver are set to the same position, any

combination of settings will operate the fan as

long as the transmitter and receiver are set to

the same position.(Figure8)

Step 1. (Figure 9) Insert the receiver into

the mounting bracket with the flat side of

the receiver facingthe ceiling.

Step 2. (Figure 10) Motor to Receiver

Electrical Connections: Connect the black

wire from the fan to black wire marked "TO

MOTOR L". Connect the white wire from

the fan tothe white wiremarked "TO MOTOR

N" from the receiver. Connect the blue wire

from the fan to the blue wire marked "For

Light" from the receiver. Secure the wire

connections with the plastic wire nuts

provided.

Step 3. (Figure 10) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire

connections with the plastic wire nuts

provided.

Step 4. (Figure 10) If your outlet box has a

ground wire (greenor bare copper) connect it

Figure 9

Receiver

Hanger

bracket

ONON

Figure 8

Code switch

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 7

Hanger pin

Locking pin Collar cover

Canopy

cover

To the fan ground wires; otherwise connect

the hanging bracket ground wire to the

mounting bracket. Secured the wire

connection with a plastic nut provided. After

connecting the wires spread them apart so

that the green and white wires are on one side

of the outlet box and black and blue wires are

on the other side. Carefully tuck the wire

connections up intothe outlet box.

Finishing the

Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and

over the 2 screws on hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with one hand, slide the canopy

cover over the screws and rotate clockwise

until tight. Note: adjust the canopy screws as

necessary until the canopy and canopy cover

are snug. (Fig.11)

Figure 11

SUPPLY CIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

WHITE

BLUE

BLACK

ONON

Outlet box

Hanger

bracket

Canopy

cover

Screws

WARNING

Make sure thenotch on the hanging

bracket properly sitsin the groove in the

hanger ball beforeattaching the canopy

to the bracketby turning the housing

until it dropsinto place.

Rubber

washer

Blade

arm

Figure 12

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach the blades to the blade arms

using three screws and rubber washers as

shown in Figure 12. Start a screw into the arm,

do not tighten. Repeat for the 2 remaining

screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the slot

in the bottom motor housing, then tighten the

two screws and washers already installed in the

blade arms (Figure13).

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with the kit.

Figure 13

Motor

Blade arm

Slot

Tab

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade arm

screws are secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 14. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should beequal within 1/8".

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

Touching

ceiling

Figure 14

WARNING

TO REDUCE THERISK OF PERSONALINJURY,

DO NOT BENDTHE BLADE HOLDERS

WHILE INSTALLING,BALANCING THE

BLADES, OR CLEANINGTHE FAN. DO NOT

INSERT FOREIGNOBJECTS BETWEEN

ROTATING FANBLADES.

Other manuals for 286-780

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY Havenville User manual

HAMPTON BAY

HAMPTON BAY SEAPORT AL634-WH User manual

HAMPTON BAY

HAMPTON BAY HAWKINS II Series User manual

HAMPTON BAY

HAMPTON BAY 91646 User manual

HAMPTON BAY

HAMPTON BAY Babiberre User manual

HAMPTON BAY

HAMPTON BAY SW18030 BN User manual

HAMPTON BAY

HAMPTON BAY AERATRON User manual

HAMPTON BAY

HAMPTON BAY Copperhead User manual

HAMPTON BAY

HAMPTON BAY Palisades User manual

HAMPTON BAY

HAMPTON BAY 51315 User manual

HAMPTON BAY

HAMPTON BAY 52202 User manual

HAMPTON BAY

HAMPTON BAY Devereaux II User manual

HAMPTON BAY

HAMPTON BAY Tahiti Breeze User manual

HAMPTON BAY

HAMPTON BAY MINNA HE-12026 User manual

HAMPTON BAY

HAMPTON BAY ASBURY User manual

HAMPTON BAY

HAMPTON BAY 553-295 User manual

HAMPTON BAY

HAMPTON BAY ETRIS 52 User manual

HAMPTON BAY

HAMPTON BAY 178 128 User manual

HAMPTON BAY

HAMPTON BAY CEVA User manual

HAMPTON BAY

HAMPTON BAY Everstar User manual

HAMPTON BAY

HAMPTON BAY HALWIN AK396H-BN User manual

HAMPTON BAY

HAMPTON BAY Cassaro User manual

HAMPTON BAY

HAMPTON BAY SAN MARINO 91153 User manual

HAMPTON BAY

HAMPTON BAY Palm Beach II User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual