HAMPTON BAY SUSSEX User manual

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

138-282

135-903

11289

792145350231

792145350248

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit......................................................................................................................

Your Fan ........................................................................................................................

Troubleshooting .............................................................................................................................

Specifications ................................................................................................................................

Operating

10.

11.

12.

Table of Contents

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breakeror fuse boxbefore beginning.

2. Allwiring must bein accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fanspeed control device.

4. WARNING: To reduce the risk of personal injury, use only the two

steel screws (and lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may

need to bereplaced, consult aqualified electrician ifin doubt.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

10. Do not use water or detergents when cleaningthe fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

12. Electrical diagrams are for reference only. Light kits that are not

packed with the fan must be UL Listed and marked suitable for use

with the model fan you are installing. Switches must be UL General

Use Switches. Refer to the Instructions packaged with the light kits

and switches forproper assembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only UL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades tothe floor.

7. Do not operate the reverse switch while the fan blades are in motion.

The fan must be turned off and the blades stopped before reversing the

blades direction.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE ARMS(ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpacking Your Fan 2.

Unpack your fanand check thecontents. You should havethe following items:

14. Loose partsbag containing:

a. Blade attachmenthardware

()

b. Mounting hardware

( 3 plasticwire connectors)

16 screws

2. Canopy assembly

Set of blades(5)

Ball/downrod assembly

Collar cover

Fan motor assembly

6. Set ofblades arms (5)

7. Mounting plate

. Glass shade(3)

10.

11. 7 W

12.

13.

Light kit assembly

Pull chains andfobs (3)

att candelabra bulbs(4)

60 Watt medium base bulbs (3)

Balancing kit

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 877-898-1881

NOTE

FOR NON-LIGHT USEPURPOSE, THE

SWITCH BOX ISAVAILABLEBY CALLING

THE TOLLFREE NUMBER

877-898-1881

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing ULlisted mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourHampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

24 angle

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps belowto hang yourfan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise.(Fig.5)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket turn

from the screw head and turning the canopy

counter clockwise.(Fig, 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shownin Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided withyour outlet box.

Step 5. Remove the hanger pin, locking pin

and set screws from the top of the motor

assembly.

Step 6. Route wires exiting from the top of

the fan motor through the collar cover,

canopy cover, canopy and then through the

ball / downrod.(Fig. 7)

a half

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of

the motor housing (Fig.7). Carefully insert the

hanger pin through the holes in the collar and

downrod. Be carefulnot to jam the pin against

the wiring inside the downrod. Insert the

locking pin through the hole near the end of

the hanger pin until it snaps into its locked

position, as notedin the circleinset of Fig. 7. Mounting

screws

(supplied with

electrical box)

Tab

Ceiling

mounting

plate

UL Listed

electrical

box

Figure 6 120V Wires

Washers

WARNING

FAILURETO PROPERLY INSTALL LOCKINGPIN

AS NOTED INSTEP 7 COULD RESULT IN FAN

LOOSENING ANDPOSSIBLYFALLING.

Step 8. Tighten two set screws on top of the fan

motor firmly (Figure 7)

Step 9. Place the downrod ball into the hanger

bracket socket.

Figure 5

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 7

Hanger pin

Locking pin Collar cover

Canopy

cover

CAUTION

REMOVE 5 RUBBERPACKINGMOUNTS AND

DISCARD BEFORE INSTALLATION.

Making the Electrical

Connections

Remember to disconnect the power.

Follow the steps below to connect the fan to your household

wiring. Use the wire connecting nuts supplied with your fan.

Secure the connectors with electrical tape. Make sure there are

no loose strands or connections.

Step 1 Connect the fan supply (black) wire and light supply (blue)

wire to the black household supply wire as shown in Figure 8.

Step 2. Connect the netura fan (white) wire to the white netura

household wire.

Step 3 Connect the fan ground wire (green) to the household

ground wire.

Step 4 After connecting the wires, spread them apart so that the

green and white wires are on one side of the outlet box and the

black and the blue wires are on the other side.

Step 5 Turn the connecting nuts upward and push the wiring into

the outlet box.

Figures 9 and 10 illustrate the wiring connections for optional

wall control (available at your Hampton Bay Retailer, the wire

color out of wall control may vary, see wall control's installation

manual for correct wire connections.)

NOTE

LIGHT KITS ARE AVAILABLE AT YOU

HAMPTON BAYRETAILER. THE FAN IS

ALREADY WIRED TO SUPPORT THE LIGHT KIT OPTION.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

OTHER PERSONAL INJURY. MOUNT FAN ONLY ON AN

OUTLET BOX OR SUPPORTING SYSTEM MARKED

ACCEPTABLE FOR FAN SUPPORT.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.

DO NOT USE THIS FAN WITH ANYSOLID-STATE SPEED

CONTROL DEVICE.

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITEWHITE

BLACK

BLUE

GREEN

WHITE

BLUE

BLACK WHITE

Figure 8

Diagram indicates optionallight kit wiring.

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 9

Diagram indicates optionallight kit wiring.

Light Switch

WHITE

BLUE

BLACK WHITE

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 10

Diagram indicates optionallight kit wiring.

Light

Fan

WHITE

BLUE

BLACK WHITE

Figure 11

Outlet box

Hanger

bracket

Canopy

cover

Screws

Finishing the

Installation

Step 1. Slide the canopy up to the ceiling and

over the 2 screws on the hanger bracket. Rotate

canopy to lock in place. Next, while holding the

canopy with one hand, slide the canopy cover

up and over the screws, rotate and lock in place.

NOTE: Adjust the canopy screws as necessary

until the canopy and canopy cover are snug.

(Fig. 11)

WARNING

Make sure thenotch on thehanging

bracket properly sitsin the groovein the

hanger ball beforeattaching the canopyto

the bracket byturning the housinguntil it

drops into place.

Rubber

washer

Blade

arm

Figure 12

Blade

Screws

Attaching the Fan

Blades

Step 1 Attach the blades to the blade arms

using three screws and rubber washers as

shown in Figure 12. Start a screw into the arm,

do not tighten. Repeat for the 2 remaining

screws and washers.

Step 2 Tighten each screw securely starting

with the center screw. Make sure the blade is

straight.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the slot

in the bottom motor housing, then tighten the

two screws and washers already installed in the

blade arms (Figure13).

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with the kit.

Figure 13

Motor

Blade arm

Slot

Tab

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct

most fan wobbling problems. Check after

each step.

1. Check that all blade and blade arm

screws are secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 14. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should beequal within 1/8".

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

Installing the Mounting

Plate

Step 1. Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws.

(Do not remove)

Step 2. Place the key holes on the mounting

plate over the 2 screws previously loosened

from the mounting ring, turn mounting plate

until it locks in place at the narrow section of

the key holes. Secure by tightening the 2

screws previously loosened and the one

previously removed. (Fig.15)

Mounting plate

Mounting ring

Screws

Figure 15

Touching

ceiling

Figure 14

WARNING

TO REDUCE THERISK OF PERSONALINJURY,

DO NOT BENDTHE BLADE HOLDERS

WHILE INSTALLING,BALANCING THE

BLADES, OR CLEANINGTHE FAN. DO NOT

INSERT FOREIGNOBJECTS BETWEEN

ROTATING FANBLADES.

This manual suits for next models

Table of contents

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY YG529-WH User manual

HAMPTON BAY

HAMPTON BAY Noella User manual

HAMPTON BAY

HAMPTON BAY Colonial Bamboo User manual

HAMPTON BAY

HAMPTON BAY MADISON AK30A-BN User manual

HAMPTON BAY

HAMPTON BAY TY-50-L (HD) User manual

HAMPTON BAY

HAMPTON BAY BAYFIELD User manual

HAMPTON BAY

HAMPTON BAY Gazebo II Plus User manual

HAMPTON BAY

HAMPTON BAY YG188M-NI User manual

HAMPTON BAY

HAMPTON BAY Marlston N375B-BN User manual

HAMPTON BAY

HAMPTON BAY WDF9-2 User manual

HAMPTON BAY

HAMPTON BAY GAZEBO II YG188-WH User manual

HAMPTON BAY

HAMPTON BAY GRANTWAY 48 RD5114B-BN User manual

HAMPTON BAY

HAMPTON BAY Babiberre User manual

HAMPTON BAY

HAMPTON BAY Andover 640-655 User manual

HAMPTON BAY

HAMPTON BAY Parker Ridge User manual

HAMPTON BAY

HAMPTON BAY 855975 User manual

HAMPTON BAY

HAMPTON BAY 52-RMG User manual

HAMPTON BAY

HAMPTON BAY 567-472 User manual

HAMPTON BAY

HAMPTON BAY Havenville User manual

HAMPTON BAY

HAMPTON BAY Antigua Plus User manual

HAMPTON BAY

HAMPTON BAY Pendleton 91252 User manual

HAMPTON BAY

HAMPTON BAY SW18030 BN User manual

HAMPTON BAY

HAMPTON BAY AG524PR-FB User manual

HAMPTON BAY

HAMPTON BAY LYNDHURST 51015 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual