HAMPTON BAY Asbury Plus User manual

60” Asbury Plus

Ceiling Fan by Hampton Bay

Accu-Arm™ for Accurate

and Easy Installation

Steeper Blade Pitch for

Greater Air Movement

3-Speed Reverse Function for

Year-Round Comfort and Savings

Tri-Mount Installation

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our

Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.

Please reference your SKU (434 149 oil-rubbed bronze, 434 346 brushed nickel, 873 937 gilded espresso)

or UPC (082392 266028 oil-rubbed bronze, 082392 266127 brushed nickel, 082392 266929 gilded espresso).

Thank you for purchasing this Hampton Bay ceiling

fan. This product has been manufactured with the

highest standards of safety and quality. The nish

of this fan is weather resistant, but over time will

naturally weather and fade.

Safety Rules ........................................1

Unpacking Your Fan..........................2

Installing Your Fan ............................3

Operating Your Remote Control ......11

Operating Your Fan ...........................12

Care of Your Fan................................13

Troubleshooting..................................13

Specications ......................................14

Warranty Information.......................15

Table of Contents

UL Model No. 60-ABR

Safety Rules ........................................1

Unpacking Your Fan..........................2

Installing Your Fan ............................3

Operating Your Remote Control ......11

Operating Your Fan ...........................12

Care of Your Fan................................13

Troubleshooting..................................13

Specications ......................................14

Warranty Information.......................15

1. To reduce the risk of electric shock, insure electricity

has been turned off at the circuit breaker or fuse box

before beginning.

2. All wiring must be in accordance with the National

Electrical Code ANSI/NFPA 70-1999 and local electrical

codes. Electrical installation should be performed by a

qualied licensed electrician.

3. WARNING: To reduce the risk of re or electric shock, do

not use this fan with any solid-state speed control device.

4. CAUTION: To reduce the risk of personal injury, use only

the screws provided with the outlet box.

5. The outlet box and support structure must be securely

mounted and capable of reliably supporting 35 lbs. (15.9

kg). Use only UL Listed outlet boxes marked “Acceptable

for Fan Support of 35 lbs. (15.9 kg) or less.”

6. The fan must be mounted with a minimum of 7 feet

clearance from the trailing edge of the blades to the oor.

7. Do not operate reversing switch while fan blades are in

motion. Fan must be turned off and blades stopped before

reversing blade direction.

8. Avoid placing objects in path of the blades.

9. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the

grounded conductor and the equipment-grounding

conductor on one side of the outlet box, and the ungrounded

conductor on the other side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are

not packed with the fan must be UL listed and marked suitable

for use with the model fan you are installing. Switches must be

UL General Use Switches. Refer to the instructions packaged

with the light kits and switches for proper assembly.

13. All set screws must be checked and retightened where nec-

essary before installation.

Safety Rules 1.

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT TO OUTLET BOX MARKED ACCEPTABLE FOR FAN

SUPPORT OF 35LBS (15.9 KG) OR LESS AND USE SCREWS PROVID-

ED WITH THE OUTLET BOX.

PLEASE REMOVE RUBBER MOTOR STOPS ON THE BOTTOM OF THE

FAN BEFORE INSTALLING BLADES OR TESTING THE MOTOR.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS WHEN INSTALLING THE BRACKETS, BALANCING

THE BLADES, OR CLEANING THE FAN.

a. Blade attachment hardware

(15 screws)

b. Electrical & Mounting Hardware

(3 plastic wire connectors, 1 hanger pin, 1

locking pin, 1 rubber gasket)

c. Extra Plug (for non-light kit use)

d. Extra Blade Bracket Attachment

Hardware

(1 screw and lockwasher)

7. Glass Bowl

8. Bulbs (3)

9. Light Kit

10. Decorative Motor Collar Cover

11. Remote Control & Receiver

1. Slide-On Mounting Plate (inside canopy)

2. Canopy with Canopy Ring attached

3. Downrod and Hanger Ball Assembly

4. Blade Bracket (Flange) Set (5)

with blade bracket screws pre-installed

5. Fan Motor Assembly

6. Blades (5)

2. Unpacking Your Fan

IMPORTANT:THIS PRODUCT AND/OR COMPONENTS ARE COVERED BY

ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436; 5,988,580;

5,971,573; 6,010,110; 6,010,306; 6,039,541; 6,046,416 AND OTHER

PATENTS PENDING.

Unpack your fan and check the contents. You should have the following items:

CAUTION: Changes or modications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate the

equipment.

Installing Your Fan 3.

Tools Required

Phillips screw driver, straight slot screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing outlet box, then read

the following instructions. Disconnect the

power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 35 lbs.)

Do not use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different

ways to mount the outlet box.

Outlet Box

Recessed

Outlet Box

Ceiling

Mounting

Plate

Provide Strong

Support

Note: You may need a longer downrod to

maintain proper blade clearance when install-

ing on a steep, sloped ceiling. The maximum

angle allowable is 30˚. If the canopy touches

downrod, remove the decorative canopy

bottom cover and turn the canopy 180˚ before

attaching the canopy to the mounting plate.

Outlet Box

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Hampton Bay retailer).

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

TO OUTLET BOX MARKED “ACCEPTABLE

FOR FAN SUPPORT OF 35LBS. (15.9 KG)

OR LESS”, AND USE SCREWS PROVIDED

WITH THE OUTLET BOX. OUTLET BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPT-

ABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELEC-

TRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

different procedures to follow for the two

types of installation.

Standard Ceiling Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

2. Remove the mounting plate from the

canopy by loosening the four screws on

the top of the canopy. Remove the two

non-slotted screws and loosen the slotted

screws. This will enable you to remove the

mounting plate (Figure 6).

Hanging the Fan

REMEMBER to turn off the pow-

er. Follow the steps below to hang your

fan properly.

NOTE: This ceiling fan is supplied with two

types of hanging assemblies; the standard

ceiling installation using the downrod with

ball and socket mounting, and the “close-to-

ceiling” mounting. The “close-to-ceiling”

mounting is recommended in rooms with

less than 8-foot ceilings or in areas where

additional space is desired from the oor

to the fan blades. When using standard

downrod installation, the distance from the

ceiling to the bottom of the fan blades will be

approximately 12 inches. The “close-to-ceiling”

installation reduces the distance from the

ceiling to the bottom of the fan blades to

approximately 7 inches.

Once you have decided which ceiling

installation you will use, proceed with the

following instructions. Where necessary,

each section of the instructions will note the

Remove

Loosen but Do

Not Remove

Figure 6 Figure 7

3. Route the wires exiting the top of the

fan motor through the decorative motor

collar cover then the canopy ring. Make sure

the slot openings are on top. Route the wires

through the canopy and then through the

ball/downrod assembly (Figure 7).

Position

Locked

Pin in

Locking

Hanger Pin

Collar

Motor

Tighten Screws

CanopyRing

Canopy

Motor Wires

Ball/Downrod

Assembly

Hook

Ceiling

Mounting

Plate

Mounting

Screws

(Supplied With

Outlet Box)

UL Listed

Outlet

Slide Mounting

Plate Over

Screw Heads

120V Wires

Motor

Collar

Cover

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. THE

MOUNTING PLATE MUST BE MOUNTED SO

THAT THE SLOT OPENINGS ARE ON THE

LOWER SIDE BY SLIDING THE MOUNTING

PLATE FROM THE TOP DOWN. FOR A GREATER

MOUNTING ANGLE, REMOVE THE DECORA-

TIVE CANOPY BOTTOM COVER (FIGURE 9).

Turn Canopy Ring to Remove

Figure 5

“Close-to-Ceiling” Mounting

1. Remove the canopy ring from the canopy

by turning the ring to the right until it

unlocks (Figure 5).

2. Remove the mounting plate from the cano-

py by loosening the four screws on the top

of the canopy. Remove the two non-slotted

screws and loosen the slotted screws. This

will enable you to remove the mounting

plate (Figure 6).

3. Remove the decorative canopy bottom cov-

er from the canopy by depressing the three

studs (Figure 9).

4. Remove three of the six screws and lock-

washers (every other one) securing the mo-

tor collar to the top of the fan motor housing

(Figure 10).

5. Place the rubber gasket over the remain-

ing three screws, route the wires exiting

the top of the fan motor through the canopy

ring (make sure the slot openings are on

top), then proceed to place the ceiling can-

opy over the collar at the top of the motor

(Figure 11). 5.

4. Loosen, but do not remove, the set

screw on the collar on the top of the

motor housing.

5. Align the holes at the bottom of the

downrod with the holes in the collar

on top of the motor housing (Figure 7).

Carefully insert the hanger pin through

the holes in the collar and downrod. Be

careful not to jam the hanger pin against

the wiring inside the downrod. Insert the

locking pin through the hole near the

end of the hanger pin until it snaps into its

locked position, as noted in the circle inset

of Figure 7.

6. Re-tighten the set screws on the collar on top

of the motor housing (Figure 8).

7. Proceed to “Installing the Fan” section.

FAILURE TO PROPERLY INSTALL SET SCREWS

IN STEP 7 COULD RESULT IN FAN LOOSENING

AND POSSIBLY FALLING.

FAILURE TO PROPERLY INSTALL THE LOCK-

ING PIN AS NOTED IN STEP 5 COULD RESULT

IN FAN LOOSENING AND POSSIBLY FALLING.

Figure 9

Canopy

Bottom

Cover

Figure 10

Figure 11

Motor

Collar Screw and

Lockwasher

(3 of 6 Screws)

Collar

Screw and

Lockwasher

(3 Screws)

Ceiling

Canopy Canopy

Ring

Rubber

Gasket

6. Align the mounting holes with the holes

in the motor and fasten, using the three

screws and lock-washers removed in step 4

(Figure 11).

7. Tighten the mounting screws securely.

Figure 8

Tighten

Set

Screws

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE BOT-

TOM OF THE MOUNTING PLATE MUST REST IN

THE GROOVE OF THE HANGER BALL. FAILURE

TO PROPERLY SEAT THE TAB IN THE GROOVE

COULD CAUSE DAMAGE TO WIRING.

Installing Fan to

the Outlet Box

WHEN MOUNTING THE FAN ON A SLOPED

CEILING, THE STANDARD BALL/DOWNROD

MOUNTING METHOD MUST BE USED. MAKE

SURE THE MOUNTING BRACKET SLOTS ARE

ON THE LOWER SIDE BY SLIDING THE MOUNT-

ING BRACKET FROM THE TOP DOWN.

1. Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket

as shown in Figure 7.

2. Install the ceiling mounting plate on the out-

let box by sliding the mounting plate over

the two screws provided with the outlet

box. When using close-to-ceiling mount-

ing, it is important that the mounting plate

be level. If necessary, use leveling washers

(not included) between the mounting plate

and the outlet box. Note that the at side of

the mounting plate is toward the outlet box

(Figure 7).

3. Securely tighten the two mounting screws.

4. Carefully lift the assembly up to the ceil-

ing mounting plate. If using Close-to-

Ceiling mounting, hang the fan on the

hook provided by utilizing one of the

holes at the outer rim of the ceiling canopy

(Figure 12). If using standard mounting, seat

the hanger ball in the mounting plate socket.

Make sure the tab on the mounting bracket

socket is properly seated in the groove in the

hanger ball (Figure 12).

Close-to-Ceiling

Mounting Standard

Mounting

Figure 12

THE HOOK AS SHOWN IN FIGURE 12 IS ONLY

TO BALANCE FAN WHILE ATTACHING WIRING.

FAILURE TO HANG AS SHOWN IN FIGURE 12

MAY RESULT IN HOOK BREAKING, CAUSING

THE FAN TO FALL. HOOK MUST PASS FROM

INSIDE TO OUTSIDE OF CANOPY.

Making the Electrical

Connections

REMEMBER to disconnect the power. If

you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan

to your household wiring. Use the wire

connecting nuts supplied with your fan

and supplied with remote control. Se-

cure the connectors with electrical tape.

Make sure there are no loose strands or

connections (Figure 13).

1. Connect the ground conductor of the 120v

supply (this may be a bare wire or a wire

with green colored insulation) to the green

ground lead(s) of the fan (Figure 13).

2. Connect the fan motor white wire to

the receiver white wire using a wire nut

(Figure 13).

3. Connect the fan motor black wire to

the receiver black wire using a wire nut

(Figure 13).

4. Connect the fan motor blue wire to the

receiver blue wire using a wire nut

(Figure 13).

5. Connect the receiver red wire to the sup-

ply black (hot) wire using a wire nut

(Figure 13).

EACH WIRE NUT (WIRE CONNECTOR) SUP-

PLIED WITH THIS FAN IS DESIGNED TO ACCEPT

UP TO ONE 12 GAUGE HOUSE WIRE AND TWO

WIRES FROM THE FAN. IF YOU HAVE LARGER

THAN 12 GAUGE HOUSE WIRING OR MORE

THAN ONE HOUSE WIRE TO CONNECT TO THE

FAN WIRING, CONSULT AN ELECTRICIAN FOR

THE PROPER SIZE WIRE NUTS TO USE. Figure 13

BLUE

BLACK

WHITE

GREEN

WHITE

BLACK

BLUE

BLACK WHITE

WHITE

Electrical

Box

Green

Grounding

Lead

Ground

Downrod

SUPPLY CIRCUIT

Switch

Receiver

WHITE

RED

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1. Align the locking slots of the ceiling canopy

with the two screws in the mounting plate.

Push up to engage the slots and turn clock-

wise to lock in place. Immediately tighten

the two mounting screws rmly.

2. Install the remaining two mounting

screws into the holes in the canopy and

tighten rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring clockwise to lock

in place.

4. You may now proceed to attaching the

fan blades.

WHEN USING THE STANDARD BALL/DOWNROD

MOUNTING, THE TAB IN THE RING AT THE BOT-

TOM OF THE MOUNTING PLATE MUST REST IN

THE GROOVE OF THE HANGER BALL. FAILURE

TO PROPERLY SEAT THE TAB IN THE GROOVE

COULD CAUSE DAMAGE TO WIRING.

6. Connect the receiver white wire to the sup-

ply white wire (neutral) wire using a wire

nut (Figure 13).

7. After connecting the wires, spread them

apart so that the green and white wires are

one side of the outlet box and the black wire

is on the other side.

8. Turn the wire connecting nuts upward and

carefully push the wiring into the outlet box.

THE FREQUENCIES ON YOUR RECEIVER AND

TRANSMITTER HAVE BEEN PRESET AT THE

FACTORY. BEFORE INSTALLING THE RECEIV-

ER, MAKE SURE THE DIP SWITCHES ON THE

RECEIVER AND TRANSMITTER ARE SET TO

THE SAME FREQUENCY. THE DIP SWITCHES

ON THE TRANSMITTER ARE LOCATED INSIDE

THE BATTERY COMPARTMENT.

CLOSE-TO-CEILING MOUNTING

1. Carefully unhook the fan from the mount-

ing plate and align the locking slots of the

ceiling canopy with the two screws in the

mounting plate. Push up to engage the slots

and turn clockwise to lock in place. Imme-

diately tighten the two mounting screws

rmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring clockwise to lock

in place.

4. You may now proceed to attaching the fan

blades.

LOCKING SLOTS OF CEILING CANOPY ARE

PROVIDED ONLY AS AN AID TO MOUNTING.

DO NOT LEAVE FAN ASSEMBLY UNATTENDED

UNTIL ALL FOUR CANOPY SCREWS ARE EN-

GAGED AND FIRMLY TIGHTENED.

Attaching the

Fan Blades

NOTE: Your fan blade are reversible. Select

the blade side nish which best accentuates

your decor.

1. Attach blade to blade bracket using the

screws as shown in gure 14. Please note that

the rubber washers are pre-attached to the

blade bracket. Start a screw into the bracket.

Repeat for the two remaining screws.

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor by

inserting the alignment post into the slot on

the bottom of the motor and tightening the

blade bracket screws. Please note that the

blade bracket screws are pre-installed into

the blade bracket (Figure 15).

4. Repeat steps 1-3 for the remaining blades.

Blade /Blade Arm

Assembly

Screws

Slot

Alignment Post

Blade Arm

Blade

Rubber Washers

Screws

Figure 14

Figure 15

Table of contents

Languages:

Other HAMPTON BAY Fan manuals

HAMPTON BAY

HAMPTON BAY FE30-DM User manual

HAMPTON BAY

HAMPTON BAY Clarington 503 837 User manual

HAMPTON BAY

HAMPTON BAY SIDLOW 52151 User manual

HAMPTON BAY

HAMPTON BAY CEVA User manual

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-TB User manual

HAMPTON BAY

HAMPTON BAY Colby User manual

HAMPTON BAY

HAMPTON BAY BPT18-34A-5 User manual

HAMPTON BAY

HAMPTON BAY LUXENBERG EF200P-36 User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY EF200S-52 User manual

HAMPTON BAY

HAMPTON BAY 80213 User manual

HAMPTON BAY

HAMPTON BAY Edgemont 324-848 User manual

HAMPTON BAY

HAMPTON BAY 344-476 User manual

HAMPTON BAY

HAMPTON BAY HVW-30M User manual

HAMPTON BAY

HAMPTON BAY Hawthorne II User manual

HAMPTON BAY

HAMPTON BAY BPT18-34ALE-2 User manual

HAMPTON BAY

HAMPTON BAY Farmington User manual

HAMPTON BAY

HAMPTON BAY Colonial Bamboo User manual

HAMPTON BAY

HAMPTON BAY Tipton II 52" User manual

HAMPTON BAY

HAMPTON BAY 654 451 User manual

HAMPTON BAY

HAMPTON BAY SEAPORT II YG991-MBK User manual

HAMPTON BAY

HAMPTON BAY 7107-03 User manual

HAMPTON BAY

HAMPTON BAY Springview User manual

HAMPTON BAY

HAMPTON BAY YG188-NI User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual