Haier GWT900AB User manual

GWT900AW

·þ Îñ ÊÖ ²á

Service Manual

Shift washing, shift spinning blanket washing easyly

Dual drive technology and save 50% consumption of water and electricity

Pulsator type for wash efficiency, twist free and low wear

Super capacity that can wash more clothes

Shift washing, shift spinningblanket washing easyly

Dual drive technology and save 50% consumption of water and electricity

Pulsator type for wash efficiency, twist free and low wear

Super capacity that can wash more clothes

FeaturesFeatures

Special No.: SM GWT900AW Edition: 2006.07.20

Full automatic washing machine

VFD display

WD-8888-97

CONTENTS

1. Contents 1

3. Specifications

5. 5

6. Net dimension 6

7. 6

8. Parts and functions 8

9. Maintenance service and trouble shooting 9

10. Wiring diagram 13

11. 14

Features 2

Safety precautions 4

Warning and cautions

Installation and accessory parts

How to disassemble washing machine

FEATURES

Haier frenquency-cenvsion and double drive

blanket washing easily

Shift washing, shift spinning

VFD Display

Cold & warm water inlet selection

Drain up function

Cabinet with the door open in the front:

Super capacity for more clothes

Pulsator type for wash efficiency, twist free and low wear

SPECIFICATIONS

Model

Free st anding

Built under

EAN code

Energy ef f iciency class

Technical data

Level/Volume L

Residual dampness %

Volt age/f requenc y V/ Hz

Wash pow er W

Spin pow er W

Net w eight kg

Gross weight kg

Contral model

Timer

cont ral ler

Normal computeri zed

Fuzzy computeri zed

Frequency conv ers ion

Service features

Short cycle

Inlet heati ng sel ect

Heati ng sel ect ion

Spinning c yc le ( select or)

Spinning c yc le ( var iable)

Start/Pause

Pres et

Automati c bal ancing

Aesthetics(V.L.H.S.H.T)

Cabinet mater ial P=Plas ti c/ Z=Zinc king/C=Cold )

r dr um(s tainl. st eel=s / plasti c=p)

Drain type U=drain up D=drain down

Door ( glas s=g / plasti c=p)

Adjus tabl e f eet

Special f unction

Air -Bubble

Feet w heel

Hand wash

Two- in- one w it h ri nse and s pin

Water f all cur rent

Dimensions (measurements)

Height / bui lt under mm

Widt h mm

Depth / w it h open door mm

Dimensions packed( measurements packed)

Height mm

Widt h mm

GWT900AW

6901570022970

1/28L 2/36L 3/49L 4/54L 5/61L

6/67L 7/73L 8/79L 9/89L 10/95L

<115

120/60

400

300

About 79

About 87

Two dr i ve

1080

686

1180

756

SAFETY PRECAUTIONS

If the power cord is bad, to avoid risk it is required to replace it by the technicians

of our special shop or the after-sale service department. Keep the pin of the power

plug clean.

Do not share one receptacle with other

electric appliances. Do not use it in

case that the power plug is damaged

or the inserting into the receptacle is

loose.

Earth

Do not wash water-proof laundries such

as the raincoat, bicycle shelter etc. To

avoid abnormal vibration during spinning.

If the power cord is bad, to avoid risk it is required to replace it by the technicians

of our special shop or the after-sale service department. Keep the pin of the power

plug clean.

Be sure to earth the earthing wire reliably.

Do not put the machine at damp place like

the bathroom. Never wash it with water.

Do not let the machine share one receptacle

with other electric appliances. If the power

plug is damaged, or the plugging into the

receptacle is loose, do not use the plug any

more.

Do not install or store the washer where

it will be exposed to the weather.

The power cord plug should be convenient

to be pluged in or pluged out with hand

while the washing machine runs normally.

Be sure to pull the plug out and close the

water tap when the machine is idle,when

moving the machine,or when cleaning

the machine.Do not use wet hand to ins-

ert or pull out the power plug.

WARNING AND CAUTIONS

Do not decompose, repair or alter the

machine by yourself.

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Do not put any hot or heavy items (such

as the kettle with hot water ) on the

washing machine.

The handicapped or children without

care shall not use the machine.

Under certain conditions, hydrogen gas may be produced in a hot water system that has

not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

has not been used for such a period, before using the washing machine, turn on all hot

faucets and let the water flow from each for several minutes.

This will release any accumulated hydrogen gas. As the gas

is flammable, do not smoke or use an open flame during this time.

Keep the machine away from direct

sunlight and heat source like the heater.

Do not wash articles that have been

previously cleaned in, washed in, soaked

in, or spotted with gasoline, dry-cleaning

solvents, other flammable, or explosive

substances as they give off vapors that

could ignite or explode. Do not add

gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to

the wash water. These substances give

off vapors that could ignite or explode.

Petrol

Thinner

Unit mm

NET DIMENSION

INSTALLATION AND ACCESSORY PARTS

The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will

result in unstable running or stoppage of the machine. Please adjust it with following methods:

Confirm it's horizontal

Hang the plumb to confirm it's horizontal.

Adjust the adjustable feet

1) To twist the adjustable foot, please first lift up

the side of the foot slightly, and twist the foot.

2) Fasten the nut after adjustment.

Adjust the Installation position

High Low

Adjustable foot

Please install and adjust the machine according to the requirement of the manual.

It is very important to your security and correct operating the machine.

Shiping bar

Pull out

Pull the shipping bar out to avoid

damage to your washing machine

before your first use of it.

INSTALLATION AND ACCESSORY PARTS

Usage of the drain hose

Hang the outer drain hose on the proper place

before washing( do not use it toppled down

on the ground).

Attend that the outlet of drain hose shall be higher

than the water level in washtub to avoid siphon

phenomenon.

1.0m<h<1.5m

Connect the water inlet hoses

Figure 1

Figure 2

1. Attach the water inlet hoses to the hot water faucet and the cold water

faucet. Using pliers, tighten the coupling. ( As figure 1)

4. Check for leaks

(1). Swing the water inlet hose gently to confirm if it is suitable.

(2). Turn on the water faucets and check for leaks. Asmall amount of water might

enter the washers. You will drain this later.

3. Attach the hose connected with hot water faucet to the HOT water inlet valve(sign

with "H'). Attach the hose connected with cold water faucet to the COLD water

valve(sign with C).

( As figure 2)

NOTE: Do not over-tighten.

2. Run water through both faucets and inlet hoses, into a bucket or

laundry tub, to get rid of particles in the water lines that might clog the

inlet valves screens.

Install the drain hose

Outer drain hose

component Drain hose neck

Drain hose joint

Drain hose hoop

First install the drain hose hook on the parts of

outer drain hose component.

Put the drain hose clamp on the outer drain hose,

insert the outer drain hose into the joint for it, and

then clutch tightly with drain hose hoop.

Take off the lint filter.

The lint filter must be used during washing.

It must be cleaned in time after each using.

Clean up the lint in the filter.

Install the lint filter.

Clean the filter

PARTS AND FUNTIONS

Bleach injection inlet

Cabinet

Control panel

Control panel seat

Top lid

Adjustable foot

(four pieces)

Door switch

Front door

Inner tub cover

Power line

Water inlet valve

Drain hose joint

Back cover

MAINTENANCE SERVICE AND TROUBLE SHOOTING

If you replace the computer sequencer without checking the other components carefully,

the computer sequencer may be damaged again. Therefore, please first check

if the other components working normally before replacing the sequencer in maintenance.

Trouble-shooting charts

No action(The indicator is off)

Confirm that there's no power failure,

and the power plug is inserted reliably.

The power switch is at "On" mode.

Measure the voltage

of the two ends of the power input

of the sequencer.

Measure the resistance

between the white wire terminal

in the white plug on top of the wire unit

and the N pin on the power

receptacle.

Replace the sequencer.

Replace the

power cord.

Replace the wire unit.

Replace the computer

sequencer.

Connect the fuse and the

wires of the two ends.

The resistance

is 0.

The resistance

is 0.

The resistance

is 0.

Infinite

Yes

Infinite

Pull off

the power

plug Not exist

Exist

Check if the connection

between the fuse and the wires

of the two ends are well?

Measure the resistance

between the brown wire terminal

in the white plug on top of the wire

unit and the brown wire of

the lower part.

Measure the resistance

between the light blue wire terminal

in the red plug on top of the wire unit

and the light blue wire of

the lower part.

This manual suits for next models

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide