Haier AP96NACAEA User manual

Cabinet unit

Operation Manual

AP96NACAEA

AU96NATAEA

No.0010575977

Name of Parts

Parts and Functions

Operation points

Safety Precautions

Operation

Users' Attention

Maintenance

Trouble shooting

When problems occur

When troubles occur

Installation instruction

Installation procedure

Others

5-6

11-12

13-14

15-26

27-28

CONTENTS

Outlet grill

Operation panel

Inlet grill

Indoor unit

Outdoor unit

Air inlet

Air outlet

Air inlet

Name of Parts

The interface of the refrigerant pipe

Note:

Open the power switch 12 hours before the unit running.Do not cut off the power

when short time stop the unit (like one day and one night ),this is to protect the

compressor.

Do not block the air inlet and air outlet, otherwise the performance of the air

conditioner may be lowered and it will make the protection device act.

Parts and Functions

3.TEMP Setting Button

Used to set temperature. (Setting ranges: 16 C to 30 C)

1.Power ON/OFF Button

4.MODE Button

Used to select operation mode: AUTO COOL DRY FAN HEAT

AUTO

FAN

HEAT

COOL

DRY

8.LOCK Button

Used to lock operation button and LCD display contents: by pressing this button, other buttons comes out

of function and lock state display appears; if you press it again, lock state will be no more active and lock

state display will disappear.

9.TEMPERATURE Display

7.LOCK State Display

5.Operation MODE Display

6.FAN SPEED Display

2.FAN Button

Used to select fan speed:AUTO,LOW,MID,HIGH.

Mode

Used to display set temperature and room temperature.

Used for unit start or stop

Panel

LOCK

MODE FANTEMP ON/OFFTEMP

5 4 3 2 1 9

LOW MID HIGH

AUTO(Flash)

Change of fan speed

In COOLING mode, the air sending is set at AUTO,

when the indoor temperature is near the set temperature,

the fan speed will lower automatically.In HEATING

mode, when room temperature reaches the set temperature,

the compressor will stop running, and the fan will change

to LOW FAN or stop.In DEHUMIDIFYING mode, the fan

speed will change automatically.

3-minute protection function

If start the unit immediately only

after it is turned off, the compressor

will start after 3 minutes have

elapsed to protect the compressor.

Operation of air conditioner

When the ambient humidity is too high,

in COOLING or DEHUMIDIFYING

mode, there may be water dropped in the

air outlet.

Anti-cold air blowing out

During Heating operation, after starting the

unit, the indoor fan motor will not rotate

immediately to prevent cold air from blowing

out.

Defrosting function

During Heating operation, when frost formed on the

heat exchanger of outdoor unit, the air conditioner

will defrost automatically for several minutes. During

defrosting, both the fan of indoor and outdoor unit

do not run. After finishing defrosting, the air

conditioner will automatically resume operation.

Hint

When the air conditioner

is in Heating mode, it

absorbs heat from

outside and release to

indoors. So the outdoor

temperature may affect

the Heating effect.

Operation points

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

MODEFAN SWING

TEMP

CLOCK

TIMER

SET

SLEEP

FILTERRESET

RESET

ON/OFF

Safety Precautions

Notice

The system should never be

used for any other purposes

than intended such as for

preservation of food, flora

and fauna, precision devices

or work of art.

Do not put the fire

devices in the places,

which the air from

the air conditioner

can directly blow.

It may cause deterioration of

the articles.

It may cause the fire

devices cannot burn

completely.

Do not install the system where the air

outlet may directly reach the flora and

fauna.

Only use the proper specified fuse.

It will not be good for their health.

If use metal wire or copper wire to

replace the fuse, it may cause trouble

and fire accident.

Do not put or use any

spray near the air

conditioner, and do not

directly spray to the air

conditioner.

Otherwise it may cause

fire.

Safety precautions when moving, reinstalling and repairing the air conditioner

Warning

OFF

Do not use the pow-

er switch to turn of

or off the air condit-

ioner.

Do not use such equipment as a water heater,

etc., around the indoor unit

or the wire controller.

It may cause fire or

Creepage.

If the system is operated at the vicinity of such

equipment that generates steam, condensed

water may drip during cooling operation or it

may cause Creepage or short-circuit.

When operating the system sim-

ultaneously with a combustion

apparatus, indoor air must be v-

entilated frequently.*

Insufficient ventilation may ca-

use the danger of lack of oxygen.

When cleaning, please

stop the unit and cut o-

ff the power first.

Do not put the water containers,

such as vase, on the unit.

Do not perform

cleaning, when the

indoor fan motor is

rotating in high

speed.

If the water enters

into the unit and damages

the electric insulation material,

it may cause electric shock.

Do not refit the air conditioner.

When repair is needed, please

contact your dealer.

When moving the air conditioner to another

installation place, please contact the dealer

or the professional installer.

Improper repair may

cause water leakage,

electric shock and fire accident.

Improper moving and reinstallation may cause

water leakage, electric shock and fire accident.

AUTO, COOL , HEAT and DRY Operation

1. Unit start

Press ON/OFF button,unit starts.

Previous operation status appears on LCD (except for TIMER,SLEEP and SWING setting)

3.Temperature setting

Then select AUTO run or select COOL operation or select DRY operation or select HEAT operation

or select FAN operation

2.Select operation mode

Press MODE button. At each press, operation mode changes as follows:

Press TEMP button.

Every time the button is pressed, temp. setting increases 1 C; if the button is kept pressed, temp. setting will

increase quickly.

Every time the button is pressed, temp. setting decreases 1 C, if the button is kept pressed, temp. setting will

decrease quickly.

Set proper temperature

4.Adjust FAN button

Press FAN button.At each press, fan speed changes as follows:

Air conditioner will run at the selected fan speed.

5. Unit stop

Press ON/OFF button,unit stops.

In FAN mode, the temperature setting is not displayed on LCD,and "Auto Fan" not available.

In DRY mode, when room temperature becomes 2 C higher than temperature setting, unit will run intermittently

at LOW speed regardless of FAN setting. When room temperature is lower than temperature setting, unit will

only run FAN operation.

In HEAT mode,warm air will blow out after a short period of time due to cold-draft prevention function.

InAuto mode,unit will adjust fan speed according to room temperature automatically.

Operation

Temp. setting +2 C

Temp.setting

On reaching temp.setting

+2 C, unit will run in mild

DRY mode.

Ultra-low air flow

COOL operation starts

when room temp.is

higher than temp.

setting.

LOCK

MODE FANTEMP ON/OFFTEMP

AUTO(Flash) LOW MID HIGH

AUTO FANHEATCOOL DRY

Operation

Fan Operation

1.Unit start

Press ON/OFF button to start your air conditioner.

Previous operation status appears on LCD (except for TIMER, SLEEP, and SWING setting).

2.Select operating mode

Press MODE button. At each press, operation mode changes as follows:

3. Adjust fan speed

Press FAN button. At each press, fan speed changes as follows:

Air conditioner will run at the selected fan speed.

4. Unit stop

Press ON/OFF button to stop unit.

Then select FAN

About FAN mode

When the air conditioner runs in FAN mode, it is not possible to select

AUTO FAN or to set temperature.

LOCK

MODE FANTEMP ON/OFFTEMP

AUTO FANHEATCOOL DRY

Usersí Attention

Set proper room temperature

Not too low or high and make every peop-

le in the

room

feel

comfortable.

Do not let the cold air blows directly to

human body for a long time and do not

make the room temperature drop too

low.

Otherwise, it may

cause uncomfortable

or bad to your health.

Cut off

power

The room should often ventilate.

After a long-time

of using air

conditioner, the

room must be

ventilated.

Do not keep the doors and windows

open

Otherwise, it

may lower the

efficiency of

the air conditioner.

Television, radio and acoustics, etc.

equipment should keep over 1m from

indoor unit and wire controller.

Otherwise, they may

disturb the image

and cause noise.

If do not use the air conditioner

for a long time, it is necessary to

cut off power.

If do not cut

off power, the

unit may consume

power. In order to protect the unit,

before using the air conditioner

again, turning on the power at least

12 hours in advance.

The windows should be hung

with curtains or blinds.

Do not let the sun

shine directly shine

in the room; do not

let the outdoor air

enter room.

The articles must keep dry cannot

be put under the indoor unit.

When the humidity

is over 80% or

the drainage

outlet is blocked,

the indoor unit may drop water.

Do not put articles around the

air inlet and outlet.

This kind of obstacle can lower the

efficiency of the air conditioner or

cause unit trouble.

The air conditioner can only be used

in air conditioning. It can not be

used in other purpose.

Do not use the air conditioner in some

specific purpose, such as storage or

protect food, animals, plants, precise

instrument and

artwork,

otherwise,

the quality

of them may

be declined.

Do not press tightly with the LCD part of

the wire controller to avoid damage of it.

The airflow cannot directly blow

to the pets and plants.

Otherwise, pets

and plants

may be hurt.

Do not put any drying

devices under

the indoor unit.

The heat may cause

the deformation of

indoor unit.

Cooling is

26~28*

Heating is

18~23*

Maintenance

Disconnect power supply Don't touch it with wet

hand Don't wash with hot water

or solvent to clean the unit

Don't use hot water over 40 C,

as this may cause damage to air filter.

Wipe air filter carefully.

Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with

clean and soft cloth.

If air conditioner is very dirty, clean it with cloth

soaked in neutral detergent,then wipe off the

detergent with clean water.

Don't use water higher than 40 C , which will cause

discoloring and deformation.

Don't use insecticide or other chemical detergents.

Caution:

Indoor and outdoor cleaning

Use water or vacuum cleaner to clean it.

If it is extremely dirty, wash it with

neutral detergent or soap water.

Wash it with clean water and install

it after complete dry.

Air filter cleaning

40*

First cut off the power supply, then turn

the embedded part of air inlet grille

upwards, finally use cross-shaped

screwdriver to screw off the screw.

Remove air inlet grille

40*

Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with

clean and soft cloth.

If air conditioner is very dirty, clean it with cloth

soaked in neutral detergent,then wipe off the

detergent with clean water.

Don't use water higher than 40 C , which will cause

discoloring and deformation.

Don't use insecticide or other chemical detergents.

Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with

clean and soft cloth.

If air conditioner is very dirty, clean it with cloth

soaked in neutral detergent,then wipe off the

detergent with clean water.

Don't use water higher than 40 C , which will cause

discoloring and deformation.

Don't use insecticide or other chemical detergents.

Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with

clean and soft cloth.

If air conditioner is very dirty, clean it with cloth

soaked in neutral detergent,then wipe off the

detergent with clean water.

Don't use water higher than 40 C , which will cause

discoloring and deformation.

Don't use insecticide or other chemical detergents.

Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with

clean and soft cloth.

If air conditioner is very dirty, clean it with cloth

soaked in neutral detergent,then wipe off the

detergent with clean water.

Don't use water higher than 40 C , which will cause

discoloring and deformation.

Don't use insecticide or other chemical detergents.

Maintenance

After season maintenance

Before season maintenance

Let the unit run in Fan mode for half a day in a

fine weather to dry completely the unit inside.

Turn off the unit and pull out power plug.

There might be certain power consumption even

if unit is stopped.

Clean air filter and indoor unit, cover outdoor

unit after cleaning.

Check if there are obstacles at inlet

and outlet of indoor and outdoor unit,

whick will reduce unit efficiency.

To protect compressor at start, please connect

external power supply to the unit 12 hrs prior

to starting.Also please keep the power supply

switch ON during the whole season.

Don't fail to attach air filter after making sure it is cleaned.

Dust will enter into unit causing damages or faults if it is running without air filter.

This manual suits for next models

Table of contents

Other Haier Air Conditioner manuals

Haier

Haier HSU-18CB03 User manual

Haier

Haier AP162ACMAA User manual

Haier

Haier Novel Series User manual

Haier

Haier HWS20VCA User manual

Haier

Haier HSU-09LEA13-W User manual

Haier

Haier HC18D2VAR User manual

Haier

Haier GE APPLIANCES USYL24UCDDA User manual

Haier

Haier HSU-09HEA13/R2 User manual

Haier

Haier HWR05XCL Assembly instructions

Haier

Haier HTWR12VCK User manual

Haier

Haier HSU-12HEB03 User manual

Haier

Haier HWS05XCA User manual

Haier

Haier AC-8888-107 User manual

Haier

Haier AS30PF2LAA User manual

Haier

Haier AC282ACBCA User manual

Haier

Haier HSU-09HV03 User manual

Haier

Haier HSU-09LF03 User manual

Haier

Haier 1U24GS4ERA User manual

Haier

Haier HM-05CB03 User manual

Haier

Haier HSU-07HRA03 User manual

Haier

Haier HWR05XC7 - 5,200 BTU Window Air Conditioner User manual

Haier

Haier HSU-18CVY03 User manual

Haier

Haier HS-06CA03 User manual

Haier

Haier HSU-09HVD03/R2 - annexe 2 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual