Grundig GCA-B3323V User manual

GCA-B3323V.42.1.09.02.2012

Owner's Manual

Cameras & Domes

GCA-B3323V 1/3" CCD Col/B&W Fixed Dome Camera

GCA-B3326V 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED

Content:

1. Available Versions 2

2. Important Safety Instructions 2

3. Package Contents 3

4. Installation 3

1. Part Names 4

2. Base Installation 5

3. Mounting Housings to Electrical Junction Boxes 6

4. Connections 7

5. 3-Axis Gimbal Adjustment 7

6. Zoom & Focus Adjustment 8

7. IR-LED On/Off Switch 8

8. Fan &Heater (optional) 9

5. OSD Control Keys 9

6. OSD Menu 10

1. LENS 11

2. SHUTTER/ AGC 12

3. WHITE BAL (White Balance) 13

4. PICT ADJUST (Picture Adjustment) 15

5. NR (Noise Reduction) 16

6. ATR (Adaptive Tone-Curve Reproduction) 16

7. BACKLIGHT 16

8. CAMERA ID 17

9. DAY/NIGHT 17

10. MOTION DET (Motion Detection) 18

11. PRIVACY 19

12. SYNC 20

13. LANGUAGE 20

14. CAMERA RESET 20

15. NEXT / BACK 20

16. EXIT 20

17. SAVE ALL 20

1. Available Versions

These instructions apply to the following products. For the different properties of the

products please refer to the table.

2. Important Safety Instructions

Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

Incorrectly connecting the power supply or replacing battery may cause explosion, fire,

electric shock, or damage to the product. Do not connect multiple products to one single

adapter. Exceeding the capacity may cause abnormal heat generation or fire.

Do not place conductive objects (e.g. screwdrivers, coins or any metal items) or

containers filled with water on top of the product. Doing so may cause personal injury

due to fire, electric shock, or falling objects.

If any unusual smells or smoke comes out of the unit, stop using the product. In this

case, immediately disconnect the power source and contact the service center.

Continued use in such a condition may cause fire or electric shock.

If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (GRUNDIG is not liable for problems

caused by unauthorised modifications or attempted repair.)

To prevent fire or electric shock, do not expose the inside of this device to rain or

moisture.

2English

3. Package Contents

These parts are included:

- Torx Wrench: Length 90mm (1pc)

- Dowel: Length 30mm, Thickness 6mm (4pcs)

- Assembly Screws: FH M4x14 (4pcs)

- Mounting Screws: ST4x38 (4pcs)

These screws are used to mount both surface mount plate or flush mount base to a

sturdy surface. If necessary, use the dowels included.

- Pipe Cap Driver: (1pc)

This is used to open/close the pipe cap of the surface mount plate.

- Service monitor and control cable:

It is possible to set up the camera through a portable monitor and adjust the OSD menu

of the camera externally.

4. Installation

Do not install the product in a location subject to high temperature (over 50°C), low

temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock.

Keep out of direct sunlight and heat radiation sources. This may cause fire. Avoid aiming

the camera directly towards extremely bright objects such as the sun, as this may

damage the image sensor.

Do not install the unit in humid, dusty or sooty locations. Doing so may cause fire or

electric shock. Install it in a place with good ventilation.

English

When installing the unit, fasten it securely and firmly. A falling unit may cause personal

injury.

If you want to relocate the already installed product, be sure to turn the power off and

then move or reinstall it.

4.1. Part Names

1. Bubble

2. Dome Cover Ring

3. Lens

4. Safety Wire

5. Service Monitor Output Port

6. Flush Mount Base

7. Surface Mount Plate

8. Assembly Screws (Torx M4x8)

9. Assembly Screws (Philips M4x14)

10. Gimbal Bracket

11. Mounting Screws (St4x38)

12. Video/Power Cable

Caution:

To avoid smear, do not expose the camera directly to a strong light source such as the

sun or spot light.

4English

4.2. Base Installation

1. Remove the dome cover by loosening the 3 screws. Use the Torx wrench supplied.

2. Surface Mount :

Using the four ST4x38 screws, mount the surface plate to a sturdy surface.

Using the four M4x14 screws, affix the flush mount base to a surface plate.

(For flush mount application, disregard section 2.)

3. Flush Mount :

Using the four ST4x38screws, affix the flush mount base to a sturdy surface.

5English

4.3. Mounting Housings to Electrical Junction Boxes

This unit can be either flush mounted or surface mounted with Electrical Junction Boxes

using the pre-drilled mounting holes. The dome housing accommodates various

electrical junction boxes, making the installation easy and less time consuming.

NOTE:

The screws required for electrical junction boxes are not supplied with the Dome. These

screws are readily available at local electrical supply stores.

6English

4.4. Connections

- Power connection: Requires a DC 12V or AC 24V input depending on the camera

model.

- All camera models are supplied with a service monitor output on the camera module. A

control cable is included in the package.

Note:

To set up the OSD menu externally, a control cable is required.

4.5. 3-Axis Gimbal Adjustment

1. Pan: Adjust the first pan angle by turning

the gimbal 360° degrees (see figure No.1).

2. Tilt: Adjust the tilt angle by moving the

gimbal up and down (see figure No.2).

3. Rotation: Loosen the pan screw (No.3) to

adjust the pan to a desired angle (see figure

No.4) and fix the screw.

English

4.6. Zoom & Focus Adjustment

If you need to make viewing angle/focus

adjustments, loosen the lever bolts and

make the necessary adjustments as shown.

- Field of View: Telephoto (T) to Wide (W)

- Focus: Near (N) to Infinity (oo)

After the adjustments are completed,

tighten the Zoom/Focus levers.

Caution:

Focus and Zoom Lever Bolts MUST be pushed back in properly. If they touch the inside

of the dome bubble, they will cause scratches. This may effect the view of the camera.

4.7. IR-LED On/Off Switch

For the cameras with IR-LEDs, it is possible to switch off the LEDs. Please turn the

switch to ON or OFF according to your needs.

- OFF: Select OFF if the subject in the picture has an extreme IR-LED refelction.

- ON: Select ON if the subject has no IR-LED reflection.

8English

This manual suits for next models

Table of contents

Other Grundig Security Camera manuals

Grundig

Grundig GD-CI-BT4537VH User manual

Grundig

Grundig GD-CI-AC1616V User manual

Grundig

Grundig GD-CI-BP8637T User manual

Grundig

Grundig GCA-C0245P User manual

Grundig

Grundig GD-CI-BP8637V User manual

Grundig

Grundig GD-CI-AT3637V User manual

Grundig

Grundig GD-CI-AC1616V User manual

Grundig

Grundig GD-CI-CP4637V User manual

Grundig

Grundig GD-CI-AT4634T User manual

Grundig

Grundig GD-TI-AT30105K User manual

Grundig

Grundig GD-CT-CP2837V User manual

Grundig

Grundig GCT-K0126V User manual

Grundig

Grundig GCA-B1002B User manual

Grundig

Grundig GD-CI-AT2505B User manual

Grundig

Grundig GD-CI-AP4647P User manual

Grundig

Grundig GCH-K0323V User manual

Grundig

Grundig GD-CI-AT4747P User manual

Grundig

Grundig GCI-F4616T User manual

Grundig

Grundig GD-CI-DT4637T User manual

Grundig

Grundig GCI-N0503B User manual

Grundig

Grundig GD-TI-AP4507T User manual

Grundig

Grundig GCH-K0326T User manual

Grundig

Grundig GCH-K0323D User manual

Grundig

Grundig GCA-B0326D User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide