GeoVision GV-TMEB5800 User manual

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

User's Manual

GV-IP Thermal Camera

TMEB-UA-A

Under the copyright laws, this manual may not be copied, in whole or in part,

without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is

accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind

and assumes no responsibility for errors or omissions. No liability is assumed

for incidental or consequential damages arising from the use of the information

or products contained herein. Features and specifications are subject to

change without notice.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

http://www.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV

series products are trademarks of GeoVision, Inc. Windows is the registered

trademark of Microsoft Corporation.

August 2022

Scan the following QR codes for product warranty and technical support

policy:

[Warranty] [Technical Support Policy]

Contents

Notes on Safety ....................................................................................................... iii

Installation Requirements for Video Content Analysis......................................... 1

Chapter 1 Introduction........................................................................................... 3

Chapter 2 Network Connection............................................................................. 4

2.1 LAN ........................................................................................................................4

2.1.1 Access through GV-IP Device Utility........................................................... 4

2.1.2 Directly Access through IE ......................................................................... 7

2.2 WAN.......................................................................................................................9

Chapter 3 Live View ........................................................................................... 12

Chapter 4 Fire Detection and Temp Measurement............................................ 14

4.1 Fire Detection .......................................................................................................14

4.2 Temperature Measurement...................................................................................15

Chapter 5 Other Configurations ......................................................................... 18

5.1 System Configuration............................................................................................18

5.1.1 Basic Information.......................................................................................18

5.1.2 Date and Time...........................................................................................18

5.1.3 Local Config..............................................................................................19

5.1.4 Storage .....................................................................................................20

5.2 Image Configuration..............................................................................................22

5.2.1 Display Configuration ................................................................................22

5.2.2 Video / Audio Configuration.......................................................................26

5.2.3 OSD Configuration....................................................................................27

5.2.4 Video Mask ...............................................................................................28

5.2.5 ROI Configuration......................................................................................29

5.3 Alarm Configuration..............................................................................................30

5.3.1 Motion Detection .......................................................................................30

5.3.2 Other Alarms......................................................................................................31

5.3.3 Alarm In.....................................................................................................33

5.3.4 Alarm Out..................................................................................................34

5.3.5 Alarm Server.............................................................................................35

5.3.6 Audio Alarm...............................................................................................35

5.3.7 Light Alarm................................................................................................37

5.4 Event Configuration ..............................................................................................37

5.4.1 Video Exception ........................................................................................37

5.4.2 Line Crossing............................................................................................40

5.4.3 Region Intrusion........................................................................................42

5.4.4 Region Entrance........................................................................................44

5.4.5 Region Exiting...........................................................................................44

5.4.6 Target Counting ........................................................................................44

5.4.7 Face Detection..........................................................................................47

5.5 Network Configuration ..........................................................................................49

5.5.1 TCP/IP ......................................................................................................49

5.5.2 Port ...........................................................................................................50

5.5.3 Server Configuration .................................................................................51

5.5.4 Onivf..........................................................................................................52

5.5.5 DDNS........................................................................................................52

5.5.6 SNMP........................................................................................................54

5.5.7 802.1x.......................................................................................................55

5.5.8 RTSP ........................................................................................................55

5.5.9 UPNP........................................................................................................56

5.5.10 Email.......................................................................................................57

5.5.11 FTP.........................................................................................................58

5.5.12 HTTPS....................................................................................................60

5.5.13 QoS.........................................................................................................61

5.6 Security Configuration...........................................................................................62

5.6.1 User Configuration ....................................................................................62

5.6.2 Online User...............................................................................................64

5.6.3 Block and Allow Lists.................................................................................64

5.6.4 Security Management ...............................................................................65

5.7 Maintenance Configuration...................................................................................66

5.7.1 Backup and Restore..................................................................................66

5.7.2 Reboot ......................................................................................................67

5.7.3 Upgrade....................................................................................................67

5.7.4 Operation Log ...........................................................................................68

Chapter 6 Search ................................................................................................. 69

6.1 Image Search .......................................................................................................69

6.2 Video Search........................................................................................................71

6.2.1 Local Video Search...................................................................................71

6.2.2 SD Card Video Search..............................................................................72

Integration with GV-VMS........................................................................................ 74

Appendix................................................................................................................. 75

Appendix 1 Troubleshooting..........................................................................................75

Appendix 2 Common Material Emissivity.......................................................................76

iii

Notes on Safety

⚫This product is intended to be supplied by a Listed Power Unit, marked with 'Limited

Power Source', 'LPS' on unit, output rated minimum 12V/2 A or POE 48V/ 350mA or

AC24V (depending on models), no more than 2000m altitude of operation and Tma=60

Deg.C.

⚫As for the modes with PoE function, the function of the ITE being investigated to IEC

60950-1 standard is considered not likely to require connection to an Ethernet network

with outside plant routing, including campus environment and the ITE is to be connected

only to PoE networks without routing to the outside plant.

⚫Do not attempt to disassemble the camera; in order to prevent electric shock, do not

remove screws or covers.

⚫There are no user-serviceable parts inside. Please contact the nearest service center as

soon as possible if there is any failure.

⚫Avoid from incorrect operation, shock vibration, heavy pressing which can cause

damage to product.

⚫Do not use corrosive detergent to clean main body of the camera. If necessary, please

use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any

cleanser for high grade furniture is applicable.

⚫Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this

may damage the image sensor.

⚫Please follow the instructions to install the camera. Do not reverse the camera, or the

reversing image will be received.

⚫Do not operate it incase temperature, humidity and power supply are beyond the limited

stipulations.

⚫Keep away from heat sources such as radiators, heat registers, stove, etc.

⚫Do not expose the product to the direct airflow from an air conditioner.

⚫This manual is for using and managing the product. We may reserve the rights of

amending the typographical errors, inconsistencies with the latest version, software

upgrades and product improvements, interpretation and modification. These changes

will be published in the latest version without special notification.

⚫All pictures, charts, images in this manual are only for description and explanation of our

products. The ownerships of trademarks, logos and other intellectual properties related

to Microsoft, Apple and Google belong to the above-mentioned companies.

Disclaimer

⚫With regard to the product with internet access, the use of product shall be wholly at your

own risks. Our company shall be irresponsible for abnormal operation, privacy leakage

or other damages resulting from cyber attack, hacker attack, virus inspection, or other

internet security risks; however, Our company will provide timely technical support if

necessary.

⚫Surveillance laws vary from country to country. Check all laws in your local region before

using this product for surveillance purposes. We shall not take the responsibility for any

consequences resulting from illegal operations.

Cybersecurity Recommendations

⚫Use a strong password. At least 8 characters or a combination of characters, numbers,

and upper- and lower-case letters should be used in your password.

⚫Regularly change the passwords of your devices to ensure that only authorized users

can access the system (recommended time is 90 days).

⚫It is recommended to change the service default ports (like HTTP-80, HTTPS-443, etc.)

to reduce the risk of outsiders being able to access.

⚫It is recommended to set the firewall of your router. But note that some important ports

cannot be closed (like HTTP port, HTTPS port, Data Port).

⚫It is not recommended to expose the device to the public network. When it is necessary

to be exposed to the public network, please set the external hardware firewall and the

corresponding firewall policy.

⚫It is not recommended to use the v1 and v2 functions of SNMP.

⚫In order to enhance the security of WEB client access, please create a TLS certificate to

enable HTTPS.

⚫Use black and white list to filter the IP address. This will prevent everyone, except those

specified IP addresses from accessing the system.

⚫If you add multiple users, please limit functions of guest accounts.

⚫If you enable UPnP, it will automatically try to forward ports in your router or modem. It is

really very convenient for users, but this will increase the risk of data leakage when the

system automatically forwards ports. Disabling UPnP is recommended when the function

is not used in real applications.

⚫Check the log. If you want to know whether your device has been accessed by

unauthorized users or not, you can check the log. The system log will show you which IP

addresses were used to log in your system and what was accessed.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

1. FCC compliance

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

⚫Reorient or relocate the receiving antenna.

⚫Increase the separation between the equipment and receiver.

⚫Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

⚫Consult the dealer or an experienced radio/TV technician for help.

2. FCC conditions:

⚫This device complies with part 15 of the FCC Rules. Operation of this product is subject the

following two conditions:

⚫This device may not cause harmful interface.

⚫This device must accept any interference received, including interference that may cause

undesired operation.

CE Information

The products have been manufactured to comply with the following directives.

EMC Directive 2014/30/EU

vii

RoHS

The products have been designed and manufactured in accordance with Directive EU RoHS

Directive 2011/65/EU and its amendment Directive EU 2015/863 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment.

2012/19/EU (WEEE directive): The Directive on waste electrical and electronic

equipment (WEEE Directive). To improve the environmental management of WEEE,

the improvement of collection, treatment and recycling of electronics at the end of their life is

essential. Therefore, the product marked with this symbol must be disposed of in a

responsible manner.

Directive 94/62/EC: The Directive aims at the management of packaging and packaging

waste and environmental protection. The packaging and packaging waste of the product in

this manual refers to must be disposed of at designated collection points for proper recycling

and environmental protection.

REACH(EC1907/2006): REACH concerns the Registration, Evaluation, Authorization and

Restriction of Chemicals, which aims to ensure a high level of protection of human health and

the environment through better and earlier identification of the intrinsic properties of chemical

substances. The product in this manual refers to conforms to the rules and regulations of

REACH. For more information of REACH, please refer to DG GROWTH or ECHA websites.

Installation Requirements for Video Content Analysis

Thermal Detection

⚫Human

oInstallation Height: 3 ~ 6 m (9.8 ~ 19.7 ft)

oVideo Content Analysis Range: 24 m (78.7 ft) or less

oCamera View: no requirements

oAngle of Depression: 30°~ 45°recommended

⚫Vehicle

oInstallation Height: 3 ~ 6 m (9.8 ~ 19.7 ft)

oVideo Content Analysis Range: 35 m (114.8 ft) or less

oCamera View: The camera is facing the direction the traffic is coming from.

oAngle of Depression: 30°~ 45°recommended

Optical Detection

⚫Installation Height: 2.8 m (9.2 ft) or above

⚫Video Content Analysis Range:

oHuman: 10 m (32.8 ft) or less

oCar: 20 m (65.6 ft) or less

⚫Camera View: It is recommended to have a front or side view of the vehicle as illustrated

below. And no view requirements for human detection.

oRecommended camera views:

oNot recommended to use a camera with a large angle of depression

Table of contents

Other GeoVision Security Camera manuals

GeoVision

GeoVision GV-LPR CAM 10A User manual

GeoVision

GeoVision GV-IRCAM Series User manual

GeoVision

GeoVision GV-VD120D User manual

GeoVision

GeoVision 90-BX2700F-8010 User manual

GeoVision

GeoVision GV-BX130D-0 User manual

GeoVision

GeoVision GV-ADR Series User manual

GeoVision

GeoVision GV-MFD1501 User manual

GeoVision

GeoVision GV-FE2301 User manual

GeoVision

GeoVision GV-TFD Series User manual

GeoVision

GeoVision GV-BX110D User manual

GeoVision

GeoVision GV-CBW120 User manual

GeoVision

GeoVision GV-BL220D User manual

GeoVision

GeoVision GV-EBDP5800 User manual

GeoVision

GeoVision GV-VD1530 Manual

GeoVision

GeoVision GV-FD8700-FR User manual

GeoVision

GeoVision GV-IP User manual

GeoVision

GeoVision myGVcloud HCW120 User manual

GeoVision

GeoVision GV-BL1500 User manual

GeoVision

GeoVision GV-SD220 Series Operator's manual

GeoVision

GeoVision GV-BX110D User manual

GeoVision

GeoVision GV-IP Speed Dome User manual

GeoVision

GeoVision GV-LPR CAM V2.0 Series User manual

GeoVision

GeoVision GV-GVS2100 User manual

GeoVision

GeoVision GV-EBL110-2F User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications