GeoVision GV-QFER12700 User manual

QFER-QG-A

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

Quick Start Guide

GV-QFER12700

Under the copyright laws, this manual may not be copied, in whole or in part,

without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is

accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind

and assumes no responsibility for errors or omissions. No liability is assumed

for incidental or consequential damages arising from the use of the information

or products contained herein. Features and specifications are subject to

change without notice.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

http://www.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV

series products are trademarks of GeoVision, Inc. Windows is the registered

trademark of Microsoft Corporation.

October 2021

Scan the following QR codes for product warranty and technical support

policy:

[Warranty] [Technical Support Policy]

Contents

Note for Connecting to GV-VMS / DVR / NVR.................................................................... ii

Note for Recording.............................................................................................................. ii

1. Introduction................................................................................................................... 1

1.1 Packing List............................................................................................................................. 1

1.2 Overview................................................................................................................................. 1

1.3 Wire Definitions....................................................................................................................... 2

2. Installation..................................................................................................................... 3

3. Connecting the Camera................................................................................................ 5

3.1 Power Connection................................................................................................................... 5

3.2 Waterproofing the Cable......................................................................................................... 5

4. Accessing the Camera ................................................................................................. 7

4.1 System Requirements............................................................................................................. 7

4.2 Looking Up the Dynamic IPAddress ...................................................................................... 8

4.3 Configuring the IP Address..................................................................................................... 9

5. The Web Interface........................................................................................................10

5.1 Viewing Live View Video....................................................................................................... 10

6. Upgrading System Firmware ......................................................................................12

7. Restoring to Factory Default.......................................................................................13

Note for Connecting to GV-VMS / DVR / NVR

The GV-QFER12700 is designed to work with GV-VMS / DVR / NVR, a video management

system. Note the following when the camera is connected to GV-VMS / DVR / NVR:

Once the camera is connected to the GV-VMS / DVR / NVR, the resolution set on the GV-VMS

/ DVR / NVR will override the resolution set on the camera’s Web interface. You can only

change the resolution settings through the Web interface when the connection to the GV-VMS

/ DVR / NVR is interrupted.

Note: Currently, only GV-VMS, applied with the patches, supports GV-QFER12700.

Note for Recording

Mind the following when using a memory card for recording:

Recorded data on the memory card can be damaged or lost if the data are accessed

while the camera is under physical shock, power interruption, memory card detachment

or when the memory card reaches the end of its lifespan. No guarantee is provided for

such causes.

The stored data can be lost if the memory card is not accessed for a long period of time.

Back up your data periodically if you seldom access the memory card.

Memory cards are expendable and their durability varies according to the conditions of

the installed site and how they are used. Back up your data regularly and replace the

memory card annually.

To avoid power outage, it is highly recommended to apply a battery backup (UPS).

For better performance, it is highly recommended to use Micro SD card of MLC NAND

flash, Class 10.

Replace the memory card when its read/write speed is lower than 6 MB/s or when the

memory card is frequently undetected by the camera.

To ensure smooth network usage, do not access the live view from more than 20

connections.

Introduction

1. Introduction

Welcome to the GV-QFER12700 Quick Start Guide. In the following sections, you will learn the

basic installations and configurations. For a detailed user manual, see the GV-QFER12700

User’s Manual.

1.1 Packing List

• GV-QFER12700

• Self-Tapping Screw x 3

• Plastic Anchor x 3

• Torx Wrench

• Waterproof Rubber Set

• 4-Pin Alarm I/O Terminal Block

• Download Guide

• Warranty Card

1.2Overview

No.

Description

IR LED x 4

Default Button

Micro SD card slot

1.3Wire Definitions

No.

Description

Audio In (Pink)

Audio Out (Green)

4-Pin Alarm I/O Terminal Block

Power (DC 12V)

RJ-45 / PoE

Installation

2. Installation

In this chapter, you will learn how to install GV-QFER12700 with standard package.

Required Items

Tool for drilling a hole on the ceiling (user-prepared)

M4 Crosshead Screw Driver (user-prepared)

SD card (user-prepared)

1. Loosen the two screws on the dome cover with the supplied torx wrench, and remove the

dome cover by pulling it apart from the camera.

2. Place the camera on the desired ceiling or wall and mark the two screw holes.

3. Drill the marked screw holes and insert the supplied plastic anchors.

4. Align the two screw holes on the camera with the inserted plastic anchors. Fasten the

camera with the supplied self-tapping screws.

5. Close and secure the dome cover.

Note: GV-QFER12700 can be installed to the wall or ceiling with GV-Mount206-1 / 903-2 /

904-2 / 912-1 / 919. Refer to the following sections and documents.

•GV-Mount 206-1 (5.4.2 GV-FER5701 / FER12203 / FER12700 / EFER3700 /

EFER3700-W / QFER12700, GV-Mount Accessories Installation Guide)

•GV-Mount903-2 (5.1.2 GV-EFER3700 / GV-EFER3700-W / GV-QFER12700, GV-Mount

Accessories Installation Guide)

•GV-Mount904-2 (5.6.2 GV-Mount904-1, GV-Mount Accessories Installation Guide)

•GV-Mount912-1 (5.12 Power Box Mount, GV-Mount Accessories Installation Guide)

•GV-Mount919 (Appendix C: In-Ceiling Mount Installation, GV-

QFER12700 User’s Manual)

Connecting the Camera

3. Connecting the Camera

3.1 Power Connection

To power up the camera, choose one of the following options below.

Connect the DC 12V power adaptor (optional accessory) to the power connector of the

camera and the power outlet.

Connect an Ethernet cable to the RJ-45 connector of the camera and a GV-PA191 PoE

Adapter (optional accessory).

3.2 Waterproofing the Cable

Audio / Alarm I/O Cable

Follow the steps below to waterproof the Audio / Alarm I/O cables.

1. Connect the required devices to the camera and apply sealant such as silicone on holes,

voids and gaps which have potential risk to water leakage. There should be no gap

between the connectors and the cables.

2. Seal the end of the rubber coating of the cables as indicated in the figure below. Use

enough silicone gel to fill in the hose and wrap around each wire; otherwise, waterproof

function cannot be guaranteed.

RJ-45 Cable

Follow the steps below to waterproof the RJ-45 cable.

1. Insert the waterproof components through the Ethernet cable as shown below.

Insert in order

2. Insert the cable into the RJ-45 plug.

3. Assemble the waterproof rubber set.

4. If the DC cable is not in use, you can waterproof it by inserting the supplied plug into the DC

interface.

DC interface

Plug

Other manuals for GV-QFER12700

Table of contents

Other GeoVision Security Camera manuals

GeoVision

GeoVision GV-IP Speed Dome User manual

GeoVision

GeoVision GV-EBD2702: GV-EBD4700 User manual

GeoVision

GeoVision GV-BX110D User manual

GeoVision

GeoVision PPTZV10-QG-A User manual

GeoVision

GeoVision GV-GEBF4911 User manual

GeoVision

GeoVision 86-PPTZ730-P01U User manual

GeoVision

GeoVision GV Series User manual

GeoVision

GeoVision GV-LPR CAM 10A User manual

GeoVision

GeoVision GV-SD220 Series Operator's manual

GeoVision

GeoVision GV-SD220 Series User manual

GeoVision

GeoVision GV-HCW120 User manual

GeoVision

GeoVision GV-BX120D series User manual

GeoVision

GeoVision GV-SD220 Series User manual

GeoVision

GeoVision GV-BL8714 User manual

GeoVision

GeoVision GV-SD220 Series User manual

GeoVision

GeoVision GV-SD2322-IR User manual

GeoVision

GeoVision GV-IPCam Series User manual

GeoVision

GeoVision GV-FD5300 User manual

GeoVision

GeoVision FETIV212-A User manual

GeoVision

GeoVision GV-MFD1501 User manual

GeoVision

GeoVision GV-PPTZ7300 User manual

GeoVision

GeoVision GV-BX110D User manual

GeoVision

GeoVision GV-LPR2800-DL User manual

GeoVision

GeoVision GV-Fisheye GV-FE111 User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications