Genie WAHD2LBV User manual
User Manual
Please read these instructions carefully before operating the unit
and keep for further reference.
1080p AHD IR Bullet Camera
with 2.8-12mm Lens
WAHD2LBV
ii
Intro Section
Please read this instruction carefully before operating the product and keep it for
further reference. All examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
CAUTION:
• If the product does not work properly, please contact your dealer or the
nearest service centre. Never attempt to disassemble the camera yourself. We
shall not be responsible for any problems caused by unauthorised repair or
maintenance.
• Do not allow water or liquid into the camera while in use.
• When using the product, you must be in strict compliance with the electrical
safety regulations of the nation and region.
• When the product is mounted on wall or ceiling, the device needs to be firmly
fixed.
• Make sure the power supply voltage is correct before using the camera.
• Do not drop the camera or subject it to any physical shock.
• If cleaning, please use a clean soft cloth with a little neutral detergent to wipe it
gently.
• Do not aim the camera at the sun or in any area where there is bright lighting.
• The device may be burned out by a laser beam, so when any laser equipment is
in use, make sure that the surface of the device will not be exposed to the laser
beam.
• Do not place the camera in extremely hot, cold , dusty or damp locations, and
do not expose it to high electromagnetic radiation.
• To avoid heat accumulation, good ventilation is required for operating
environment.
Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Specification.................................................................................................5
1.4 Functions ......................................................................................................6
2.0 Cables ..................................................................................................................7
3.0 Product Installation..............................................................................................8
4.0 Call Up Main Menu ...............................................................................................9
4
The Genie WAHD2LBV is a 1080p AHD bullet camera with an integrated IR 2.8-
12mm lens.
1.1 Product Features
• 1080p real-time image
• Analogue high definition (AHD) video output
• True Day / Night
• 30 ~ 50m IR Range
• IP66 ingress protection
• NDAA compliant
1.2 Product Dimensions
1.0 Introduction
284mm 109mm
User Manual 1080p AHD IR Bullet Camera with 2.8-12mm Lens
5
1.3 Specification
Camera
Image Sensor 1/3” CMOS
Image Size 1080p (1920 × 1080)
Image System PAL / NTSC
Resolution 1920 × 1080
Electronic Shutter 1/50s ~ 1/50000s (PAL),
1/60s ~ 1/50000s (NTSC)
Minimum Illumination 0 Lux (LED On)
Lens 2.8–12 mm
S / N Ratio >52dB (AGC Off)
Frame Rate 30 fps (60 Hz), 25 fps (50 Hz)
Video Output BNC x1
Functions
IR Distance 30 ~ 50 m
Function Control OSD
Day & Night Yes (ICR)
WDR Yes
3D NR Yes
AGC Yes
White Balance ATW, AWC, SET, Indoor, Outdoor, Manual
Advanced Image Sharpness, Saturation, Brightness etc are Adjustable
Defog Yes
Smart IR Yes
Mirror Yes
Privacy Mask Up to 8 Areas
Motion Detection Up to 4 Areas
Defect Correction Yes (Support Live and Static Defective Pixel Correction)
Language 12 languages supported
BLC & HLC Yes
Others
Ingress Protection IP66
Power Supply DC12V (±10°C)
Working Environment Temperature: -20°C ~ 50°C,
Humidity: 10% ~ 90%
Dimensions 109 × 284 mm
Weight 1010g
User Manual 1080p AHD IR Bullet Camera with 2.8-12mm Lens
6
1.4 Functions
High Resolution
Adopt high performance sensor, providing high definition and clear image.
High Transmission Performance
Real-time transmission with high speed and long distance.
DNR
Reduce noise from brightness and colour signal.
OSD
It’s easy for the user to call the setup menu and configure the menu. The camera
settings can be clearly displayed through the main menu.
White Balance
Adjust the colour temperature according to the environment automatically.
ICR Auto Switch
The filter will filter infrared light during the daytime and change to normal at night
to ensure a high sensitivity and clear image.
AGC
Adjust the gain of amplifier, enabling the camera to output the standard video
signal in different lighting condition.
Wide Dynamic Range (WDR)
When there are both very bright and very dark areas simultaneously in the field of
view, this function will balance the brightness level and provide clear images.
Backlight Compensation (BLC)
When the back of the captured object is too much bright, you can set BLC for the
captured object to make it clearer.
High Light Compensation (HLC)
Mask and compensation the high light area.
Privacy Masking
This function allows you to block or mask certain area of a scene for privacy
purpose.
Motion Detection
The alarm will be triggered when there are moving objects captured by the
camera.
7
The cables are only for reference. The default video output will be different for
different cameras.
For the camera with video switch cable, there are two kinds of video switches,
button switch and dial switch.
Button Switch: The video outputs will recycle by holding and pressing the button
in the video switch cable for 5 seconds.
Dial Switch: Please set the video output according to the directions described on
the tag of the video switch cable.
Note:
Before switching video outputs, remove the cover of the video switch cable first.
* Some models do not have the video switch cable, please go to OSD to change
video outputs.
Video Output
Power Cable
Power Cable
Video Output
Video Switch Cable
2.0 Cables
8
Before you start, please make sure that the wall or ceiling is strong enough
to withstand 3x the weight of the camera. Please install the camera in the dry
environment.
1. Attach the drill template to the place where you want to fix the camera and
then drill screw holes according to the drill template.
2. Route and connect the cables.
3. Secure the mounting base with the camera to the wall with screws as shown
below.
4. Bracket adjustment. Before adjustment, preview the image of the camera on a
monitor and then loosen the fixed ring or screws to adjust the view angle of the
camera.
5. Focus and zoom adjustment (If the model you get is fixed lens or motorised
lens, please skip this step). Remove the cover and then adjust the focus and
zoom levers to get a clear image. Finally, tighten the screws and the lens cover.
1
2
3
Rubber Plug
Rubber Plug
Fixed Ring
Pan 360°
Pan 360°
Fixed Screws
Tilt 90°C
360°C Rotation
Lens Cover
Zoom
Focus
Tilt 90°
3.0 Product Installation
9
Access Main Menu
1. Press Enter key of the rear panel or cable of the camera to go to the main
menu.
2. Select the preview window and right click the mouse to show the following
menu list on the DVR.
3. Click on the toolbar at the bottom of the live preview window (or right click
the mouse to select “PTZ Control”).
4. Select the “OSD” tab and then click / to call up the main menu.
Menu Operation
You can select the menu by clicking (U) or (D) key on the direction area.
Click (L) or (R) key to select the menu on the left. The menu with arrow icon
which means it has sub-menu. Click / to go to the sub-menu or confirm the
settings.
If there are direction keys and enter key on the cables of the camera, you can also
use these direction keys to select menu and the enter key to go to the sub-menu
or confirm the settings.
Note:
This series of the camera must be connected to the DVR which supports calling
up main menu of camera. Different DVRs manufactured by different DVR
manufacturers may have different modes of menu operation. Please refer to the
relevant User Manual of DVR.
* Some models may not support calling up main menu, please take the final
product as the standard.
Camera Camera1
OSD PresetCruise
4.0 Call Up Main Menu
Table of contents
Other Genie Security Camera manuals
Genie
Genie VRD73TDN User manual
Genie
Genie GSDNR-6358 Manual
Genie
Genie GS5360VDC User manual
Genie
Genie SSAHD2BVAF User manual
Genie
Genie GSDNR-5355W Manual
Genie
Genie COMPACT IR BULLET CAMERA User manual
Genie
Genie HDC222 User manual
Genie
Genie PWIP8BVAF User manual
Genie
Genie SSIP2DVAF User manual
Genie
Genie HDI221 User manual
Genie
Genie GIPW4NPIR User manual
Genie
Genie WAHD2DVAF User manual
Genie
Genie SSAHD2VDAF User manual
Genie
Genie ZD2812WL User manual
Genie
Genie PWIPN2EBV User manual
Genie
Genie WIPX2LBVLPR User manual
Genie
Genie HXMB22MPV2 User manual
Genie
Genie Geniewatch NSD5451 User manual
Genie
Genie SSAHD2B User manual
Genie
Genie WIP2BVLG User manual
