GE Profile DPGT650GH Manual

For answers to your Monogram,® GE Profile™or

GE®appliance questions, visit our website at

ge.com or call GE Answer Center®service,

800.626.2000.

DPGT650GH

GE Profile™High-Efficiency Gas Dryer

Specification Revised 5/09

22-1/2

Side View Rear View

GE Profile Harmony Dryer

26-1/2

3-1/2 36

2-1/2 3-1/2

Exhaust Options: When viewed from the

front of the unit, exhaust 3-way via rear, left

and bottom. Dryer is shipped exhausted to

the rear. Alternate exhausting knockouts are

supplied. Left or bottom exhaust requires a

conversion kit.

Gas: An individual properly-grounded

branch circuit, with a three-prong grounding-

type receptacle, protected by a 15 or 20

amp circuit breaker or a time-delay fuse is

required.

Gas Dryer Electric Rating: 120V, 60Hz, 6A

Gas (BTU/HR): 25,000. Factory-equipped for

natural gas. Tested for LP gas. LP gas supply

requires a conversion kit. Check installation

instructions for correct kit and have a

qualified gas technician install a conversion

kit. See dryer ducting information for proper

installation.

Note: Dryer wall outlet must be located within

36" of service cord entry and accessible when

dryer is mounted in position.

Installation Information:For complete

information, see installation instructions

packed with your dryer.

Dimensions and Installation Information (in inches)

270195

DPGT650GH

GE Profile™High-Efficiency Gas Dryer

Specification Revised 5/09

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal

exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-

rigid) ducting can be used (Kit WX08X10077). In special installations, it may be

necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.

A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid

metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter

can be maintained throughout the entire length of the transition duct. Please see

installation instruction packed with your dryer for complete instructions when using

flexible metal (foil type) ducting.

Exhaust Length Calculation:

1.Determine the number of 90° turns needed for your installation. If you exhaust to the

side or bottom of dryer, add one turn.

2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated

is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the

duct length should be treated as a 90° elbow. A turn over 45° should be treated as a

90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any

enclosed house floor (crawl space), or into an attic, since the accumulated lint could

create a fire hazard or moisture could cause damage. Never terminate the exhaust

into a common duct or plenum with a kitchen exhaust, since the combination of lint

and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,

bird nesting, etc. The wall cap must also be located at least 12" above the ground or

any other obstruction with the opening pointed down.

Dryer Ilbow Kit, Pub. No. 14-A003 is available at additional cost. For use with side or

bottom exhaust options.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

Dimensions and Installation Information (in inches)

For answers to your Monogram,® GE Profile™or

GE®appliance questions, visit our website at

ge.com or call GE Answer Center®service,

800.626.2000.

270195

DPGT650GH

GE Profile™High-Efficiency Gas Dryer

Specification Revised 5/09

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label

on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum

of 60 sq. in. of open area equally distributed. If this closet contains both a washer and

a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes,

with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

Dryer Exhausting Information: Use metal duct only, vertical and horizontal ducting.

Best performance

Domestic

dryer models

Maximum length of 4"

dia. rigid metal duct

Number

90°

turns

Exhaust hood type

opening

2-1/2"

opening

7.1 cu. ft. capacity

electric and

gas dryers

90 ft.

80 ft.

70 ft.

60 ft.

50 ft.

67 ft.

57 ft.

47 ft.

37 ft.

27 ft.

2-1/2

Specification Revised 5/09

Features and Benefits

• 7.1 Cu. Ft. King-Size Capacity - Large enough to handle anything the

washer sends its way.

• Sensor Dry Plus - Continually monitors moisture levels to help clothes

look better longer

• Push Button Controls with LED Countdown Timer - Simplify cycle

selection and provide accurate cycle times.

• Delicate Cycle with Extra-Low Heat Setting - Maintains an average

fabric temperature of 125 degrees F to protect fine handwashables

• Stainless Steel Drum - Resists rust and won't chip, peel

or snag clothes

• 5 Heat Selections - Offer enhanced drying performance

and fabric care

• Multiple Dry Cycles - Deliver optimal drying results

• Adaptive Cool-down - Tumbles clothes with cool air to

reduce wrinkling

• Speed Dry - Delivers ready-to-go results in minutes

• Wrinkle Care Extended Tumble - Continues to tumble clothes without

heat to help prevent wrinkling and creasing

• Delay Start - Lets you do the laundry on your terms

• Variable End-Of-Cycle Signal - Adjustable volume offers

added flexibility

• Supreme Quiet Sound Package - GE's quietest sound package ever

• Reverse-A-Door - Offers added installation flexibility

• Model DPGT650GHWW –White

• Model DPGT650GHMG –Champagne

DPGT650GH

GE Profile™High-Efficiency Gas Dryer

270195

DPGT650EH/GH/WW

OWER

ANUAL

TART

AUSE

EVEL

EMP

IGNAL

YCLES

IME

DRY

ENSOR

VeryDry

MoreDry

LessDry

DampDry

Normal

60Mins.

COTTONSULTRA DELICATES

SPEEDDRY

DEWRINKLE

AIRDRY

MIXED

LOAD

ACTIVE

WEAR

DELICATES

EASYCARE

High

Off

Low

High

Medium

High

Low

Extralow

Medium

Other manuals for Profile DPGT650GH

This manual suits for next models

Table of contents

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions