GE ASM18DK Original instructions

49-7405-1 11-00 JR

AST10

ASM12

ASP12

AST12

ASV12

ASM14

ASP14

ASV14

ASM16

ASH18

ASM18

ASN18

ASP18

AST18

ASV18

ASM22

ASH24

ASM24

ASN24

ASP24

ASV24

ASW24

Air Conditioners

Owner’s Manual &

Installation Instructions

www.GEAppliances.com

Safety Information

Adapter Plugs . . . . . . . . . . . . . . . . . .3

Connect Electricity . . . . . . . . . . . . . .2

Extension Cords . . . . . . . . . . . . . . . .3

Safety Precautions . . . . . . . . . . . . . . .2

Operating Instructions

Controls—Control Knobs . . . . . .6, 7

Controls—Touch Pads . . . . . . . . .4, 5

Care and Cleaning

Air Filter . . . . . . . . . . . . . . . . . . . . . . .8

Grille and Case . . . . . . . . . . . . . . . . .8

Outdoor Coils . . . . . . . . . . . . . . . . . .8

Installation Instructions

Through the Wall

Installation–Optional . . . . . . . . . .15

Window Installation . . . . . . . . .9–14

Troubleshooting Tips . . . . . . . .16

Normal Operating

Sounds . . . . . . . . . . . . . . . . . . . . . . . .16

Consumer Support

Consumer Support . . . .Back Cover

Product Registration . . . . . . . .17, 18

Warranty . . . . . . . . . . . . . . . . . . . . . .19

Write the model and serial numbers here:

# ________________________________

Find these numbers on a label on the

side of the air conditioner.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

■ Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

■This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

■Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out from the receptacle.

■ Repair or replace immediately all electric

service cords that have become frayed or

otherwise damaged. Do not use a cord that

shows cracks or abrasion damage along its

length or at either the plug or connector end.

■ Turn the mode control

OFF

and unplug

your air conditioner before making any

repairs or cleaning.

NOTE:

We strongly recommend that any

servicing be performed by a qualified

individual.

■ For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safety, this appliance must be properly

grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet to minimize the possibility of electric

shock hazard from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be

plugged into its own individual electrical

outlet which has a voltage rating that matches

the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits

which could cause a fire hazard from

overheated wires.

See the Installation Instructions,

Electrical

Requirements

section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

www.GEAppliances.com

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS –

115-Volt models only

Because of potential safety hazards under certain

conditions, we strongly recommend against the use

of an adapter plug.

However, if you must use an adapter, where

local codes permit, a

temporary connection

may

be made to a properly grounded 2-prong wall

outlet by use of a UL-listed adapter available at

most local hardware stores.

The larger slot in the adapter must be aligned

with the larger slot in the wall outlet to provide

proper polarity in the connection of the power

cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with

one hand while pulling the power cord plug

with the other hand. If this is not done, the

adapter ground terminal is very likely to break

with repeated use.

If the adapter ground terminal breaks,

DO NOT USE

the air conditioner until a

proper ground has been established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to

make sure the outlet is properly grounded.

USE OF ADAPTER PLUGS –

115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

■ To ensure proper operation, aim the

remote control at the signal receiver

on the air conditioner.

■ The remote control signal has a range of up

to 21 feet.

■ Make sure nothing is between the air

conditioner and the remote control

that could block the signal.

■ Make sure batteries are fresh and installed

correctly–see the

Care and Cleaning

section.

About the controls on the air conditioner–models with touch pads.

Features and appearance will vary.

Air Conditioner Controls Remote Control

ON/OFF

Turns air conditioner on and off.

Display

MODE

Use to set the air conditioner to

COOL

FAN

Increase

▲

/Decrease

▼

Pads

Use to set temperature when in

COOL

mode.

FAN

Use to set the fan speed at

LOW, MED

HIGH

CIRCULAIRE

Turn on to provide continuous side-to-side

air circulation.

For fixed side-to-side air direction, turn

until the desired air direction is obtained,

then turn it

OFF

ENERGY SAVER–

Controls the fan.

ON–

The fan and compressor cycle on and off.

This results in wider variations of room

temperature and humidity. Normally used

when the room is unoccupied.

Note: The fan

will continue to run for a short time after the

compressor cycles off.

OFF–

The fan runs all the time, while the

compressor cycles on and off.

This switch must be set at

OFF

in order to use

the fan settings (on the mode control).

TIMER

ON–

When the air conditioner is off, it can be

set to automatically come on in 1 to 24 hours

at its previous setting. Each touch will set the

time in hours.

OFF–

When the air conditioner is on, it can be

set to automatically turn off in 1 to 24 hours.

Each touch will set the time in hours.

To cancel the timer, press the

TIMER

pad

until the display time disappears.

SLEEP

Press to set the air conditioner to run for

8 hours before it automatically shuts off.

When the

SLEEP

pad is pressed,

SLEEP

scrolls across the display for approximately

15 seconds, then shows the time remaining.

One hour after the sleep timer is set, the set

temperature will automatically increase 1°F.

To cancel the sleep mode, press the

SLEEP

pad a second time.

Note: The sleep timer will be cancelled if the

TIMER, ENERGY SAVER or MODE pad is pressed.

Remote Control Signal Receiver

Remote Control

Low

Fan

Med

Fan

High

Fan

CIRCULAIRE

ENERGY

SAVER On

Cool

Mode On

Fan

Only

Timer

The vent control is located on the inside of the air

louvers in the lower right corner.

When set at

, only the air inside the room will

be circulated and conditioned. When set at

OPEN

some inside air is exhausted outside.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

When the air conditioner is turned on, it will

automatically start in the setting last used.

Lights beside the touch pads on the air conditioner

control panel indicate the selected settings.

Vent Control

To open the vent, push the lever to the right.

To close it, push it to the left.

COOL Mode

Use the

COOL

mode with

HIGH, MED

LOW

fan for

cooling. Use the

INCREASE

▲

/ DECREASE

▼ pads to

set the desired temperature between 64°F and 86°F

in 1°F increments.

A thermostat is used to maintain the room

temperature. The compressor will cycle on and off

to keep the room at the set level of comfort. Set the

thermostat at a lower number and the indoor air

will become cooler. Set the thermostat at a higher

number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to COOL, it will take approximately 3 minutes

for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling–

Select the

COOL

mode and

HIGH

MED

fan with a middle set temperature.

For Maximum Cooling–

Select the

COOL

mode and

HIGH

fan with a lower set temperature.

For Quieter & Nighttime Cooling–

Select the

COOL

mode and

LOW

fan with a middle set temperature.

NOTE: If you switch from a COOL setting to OFF or to a

fan setting, wait at least 3 minutes before switching

back to a COOL setting.

Air Direction – Up and Down

Fingertip pressure on the horizontal louvers adjusts

the air direction up or down.

FAN Mode

Use the

FAN

HIGH, MED,

LOW

to provide air

circulation and filtering without cooling. Since fan

only settings do not provide cooling, a temperature

setting will not be displayed.

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

About the controls on the air conditioner–models with control knobs.

Features and appearance will vary.

Controls

Mode Controls

HIGH COOL, MED COOL

and

LOW COOL

provide

cooling with different fan speeds.

LOW FAN

HIGH FAN

provides air circulation

and filtering without cooling.

NOTE: If you move the switch from a cool setting to OFF or to

a fan setting, wait at least 3 minutes before switching back to

a cool setting.

Cooling Descriptions

For Normal Cooling

—Select

HIGH COOL

MED

COOL

with the temp control at midpoint.

For Maximum Cooling

—Select

HIGH COOL

with the

temp control at the highest number available on

your knob.

For Quieter & Nighttime Cooling

—Select

LOW COOL

with the temp control at midpoint.

Temp Controls

The temp control is used to maintain the

room temperature. The compressor will cycle

on and off to keep the room at the same level

of comfort. When you turn the knob to a

higher number the indoor air will become

cooler. Turn the knob to a lower number and

the indoor air will become warmer.

MODE CONTROLS

Your model will have one of the above type controls.

TEMP CONTROLS

Your model will have one of the above type controls.

OFF

LOW

FAN

LOW

COOL

HIGH

FAN

HIGH

COOL

MED

COOL

OFF

LOW

FAN

LOW

COOL

FAN

COOL

OFF

LOW

FAN

LOW

COOL

FAN

COOL

MED COOL

The vent control is located on the inside of the air

louvers in the lower right corner.

When set at

, only the air inside the room will

be circulated and conditioned. When set at

OPEN

some inside air is exhausted outside.

Air Direction – Up and Down (on some models)

Fingertip pressure on the horizontal louvers adjusts

the air direction up or down.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

Additional controls and important information.

Vent Control (on some models)

To open the vent, push the lever to the right.

To close it, push it to the left.

Energy Saver

(on some models)

The energy saver switch controls the fan.

—The fan and compressor cycle on and off

together. This results in wider variations of room

temperature and humidity. Normally used when

the room is unoccupied.

OFF

— The fan runs all the time, while the

compressor cycles on and off.

This switch must be set at

OFF

in order to use the

fan settings (on the mode control).

Air Direction – Side-to-Side

On some models, the side-to-side air direction is

adjusted by the louver levers or by grasping and

moving the inner vertical louvers .

CIRCULAIRE (on some models)

For fixed side-to-side air direction, set the

Circulaire switch to

until the desired air

direction is obtained, then move it to

OFF

For continuous side-to-side air circulation, set the

Circulaire switch to

and leave it there.

Air Filter

The air filter behind the front grille should be

checked and cleaned at least every 30 days or more

often if necessary.

Clean the filter with warm, soapy water. Rinse and

let the filter dry before replacing it.

CAUTION: DO NOT operate the air conditioner without

a filter because dirt and lint will clog it and reduce

performance.

To remove (on some models):

Open the inlet grille upward by pulling out the

bottom of the inlet grille.

Using the tab, pull up slightly on the filter to

release it and pull it down.

To remove (on some models):

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged

with dirt or soot they may be professionally steam

cleaned, a service available through your GE

service outlet.

Grille and Case

Turn the air conditioner off and remove the

plug from the wall outlet before cleaning.

To clean, use water and a mild detergent.

Do not use bleach or abrasives.

Care and cleaning of the air conditioner.

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Grab the tab on the filter

and pull it to the right.

Grab the tabs on

the filter and pull

it up and out.

How to Insert the Batteries

Remove the battery cover by sliding it

according to the arrow direction.

Insert new batteries making sure that the (+)

and (–) of battery are installed correctly.

Reattach the cover by sliding it back

into position.

NOTES:

■ Use 2 “AAA” (1.5 volt) batteries. Do not use

rechargeable batteries.

■ Remove the batteries from the remote control if

the system is not going to be used for a long time.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions Installation Instructions

Preparing to install the air conditioner.

Read these instructions completely and carefully.

NOTE TO INSTALLER: Leave these instructions with

the air conditioner after installation is completed.

NOTE TO CONSUMER: Keep this Owner’s Manual

and Installation Instructions for future use.

IMPORTANT NOTES:

For personal safety, this air conditioner must be

properly grounded.

It is important to have the wall outlet and circuit

checked by a qualified electrician if there is any

doubt as to whether a proper ground exists.

Follow National Electric Codes (NEC) and/or local

codes and ordinances.

CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present

special problems—consult a qualified

electrician.

Before You Begin

Some models require 115/120-volt a.c.,

60 Hz grounded outlet protected with

a 15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall outlet

you plan to use is only a 2-prong outlet, it is your

responsibility to have it replaced with a properly

grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

Electrical Requirements

■ Phillips-head screwdriver

■ Adjustable wrench

■ Ruler or tape measure

■ Scissors or knife

■ Pencil

■ Level

Tools You Will Need

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Read the section Preparing to Install the Air Conditioner before beginning.

Parts Included

Window Installation Instructions.

Type A (22 or 23)

Security bracket

Top mounting rail

Right

accordion

panel

Foam top

window gasket

Window

sash seal

Left

accordion

panel

Type B (11) Type C (2)

Bottom inner

case gasket

V-support (2)

Top mounting rail

seal strip

Other manuals for ASM18DK

This manual suits for next models

Table of contents

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual