GE AGM06 Operating instructions

GEAppliances.com

Safety Instructions ........ 2, '3

Operating Instructions

Control Knob Models ...... 6, 7

Touch Pad Models ......... 4, 5

Care and Cleaning

Air Filter .................. 8

Grille and Case ............. 8

Outdoor Coils .............. 8

Installation Instructions

Preparing to Install the

Air Conditioner ............. 9

Window Installation ...... 10-14

Troubleshooting Tips ...... 15

Normal Operating Sounds . . .16

Consumer Support

Consumer Support ......... 20

Product Registration ..... 17, 18

Warranty ................. 19

A (;3406

A GD08

AGL08

A (;3408

A GN08

A GQ08

A G1708

AGW08

AGLIO

AGMIO

AGNIO

AGQIO

AGVIO

AGWIO

AGL12

AGM12

AGN12

AGQ12

AGV12

A GL14

A GN14

AGQ14

AGV14

Writethemodelandserial numbershere:

Model #

Serial #

Find tbese numbers on a label on the

side of the air conditioner.

494435 02-02J,q

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

AWARNING!

For your safe_ the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

SAFETYPRECAUTIONS

N Use dffs appliance only tbr its intended

purpose as described in this Ouamr's

Manual.

N This air conditioner must be properly"

installed in accorxlanee with the Installation

Instructions beibre it is used.

@ Turn tim mode control m OFFand unplug

your air conditioner beIbre making any

repairs or cleaning.

NOT_We strongly recommend that any

selwicing be pertbrmed by a qualified

individual.

@ Never unplug your air conditioner by pulling

on dm power coM. Mways grip plug fimdy

and pull straight out from the receptacle.

@ Repair or replace iinmediately all electric

service cords dlat have become frayed or

othe_vise dain_ed. Do not use a cord that

shows cracks or abrasion dam_e along its

length or at either the plug or connector end.

@ For your s_ety...do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity"

of this or any other appliance.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safe_ this appliance must be properly

grounded.

The power coM of dfis appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet m minimize the possibility of electric

shock hazard from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician m make sure the outlet is

properly grounded.

Where a 2-prong wall outlet is encounmred

it is your pe*:sonal responsibility" and obliganon

m have it replaced with a properly grounded

@prong wall outlet.

The air conditioner should always be

plugged into its own individual electrical

outlet which has a voltage rating that matches

the rating plate..

This provides dm best perfomlance and also

prevents oveflCading house wMng circuits

which could cause a fire hazard from

overheated wires.

See tim Installation Instructions, Electrical

Requirements section t:or specific electlical

connection requirement_s.

GEAppliances.com

AWARNING!

USEOFEXTENSIONCORDS-77&Voltmodelsonly

Because ofpotential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However; if"you inust use an extension COIII,

it is absolumly necessary that it be a ULlismd,

14 gauge, .%wire grounding type appliance

extension cord having a grounding type plug

and outlet arid that the electiical rating of the

cor_l be 15 amperes (minimuin) arid 125 volts.

CAUtiON:

DO NOT usean extension cord with any of

the230/208 voltmodels.

USEOFADAPTERPLUGS-715-Voltmodelsonly

Because of potential safety hazards under certain

conditions, we strongly recommend against the use

of an adapter plug.

Howexei; if you mttst use an adapter, where

local codes pemfit, a temporaryconnection may

be made to a properly grounded 2-prong wall

oudet by ttse of a UL-listed adapter available

at most local hardvare stores.

The larger slot in Hie adapter mttst be aligned

with Hie larger slot in the wall outlet m provide

proper polarity in the connection of the

power coM.

When disconnecting file power cord from die

adapm*; always hold the adapter in place widi

one hand while pulling the power cord plug

widi the other hand. If dfis is not done, the

Mapter ground terminal is ve*y likely to break

widi repeated use.

If the adapter ground terininal breaks, DONOT

USE dm air"conditioner until a proper ground

has been established.

Attachingtheadapterground terminalto a wall outlet

coverscrewdoesnot groundtheapplianceunlessthe

coverscrewis metal,andnotinsulated,and thewall

outlet isgroundedthroughthehousewiring. Youshould

havethecircuitcheckedbya qualifiedelectricianto

makesuretheoutlet is properlygrounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthecontrolsontheair conditioner odels withtouchpads.

Features and appearance will varg.

FAN$PI£ED

"nlIER MOOE

Air ConditionerControls RemoteControl

Controls

)ON/OFFPad

G Turns air conditioner on and off.

@Display

Shows the set temperature or time remaining

on timer.

Gi MODE

FUse to set the air conditioner to COOLor

FANmode.

Gh Increase •/Decrease • Pads

rUse to set temperature when in COOLmode.

)FANPad

_ Use to set the fan speed to LOW(F1),MED(F2)

or HIGH(F3).

OENERGYSAVER(onsomemodels)

Controls the fan.

ON-The fhn and compressor cycle on and off

This results in wider variations of room

temperature and humidib: Normally" used

when the room is unoccupied. Note: The fan

will continue to run for a short time after the

compressor cycles off.

0FF-The fan runs all the dme, while dm

compressor cycles on and off.

_illis feature must be set at OFF in order to use

the fhn settings (on the mode control).

Note: On somemodels,theENERGYSRVER

feature cannot beset on theair conditioner.

It mustbe set usingtheremote control.

OCIRCULAIRE(onsomemodels)

For continuous side-to-side air circulation

(cool settings only'), set the Circulaire switch

to ON.

For fixed side-to-side air direction, turn ON

until the desired air direction is obvained,

dmn turn it OFF..

OTIMER Pad

ON-When the air conditioner is off; it can be

set to automatically come on in f to 12 hours

at its previous setting. Each touch will set the

timer in hours.

0FF-When the air conditioner is on, it can be

set to antomatically turn off in f to 12 hours.

Each touch will set the timer in hours. After

the timer has been on for 30 minutes, the

temperature will antomatically rise 2°E and

after another 30 minutes, it will automatically

rise 2°F again. _l]aetemperature will then stay

the same until the timer goes OFF.

TOcancel the timer,press the TIMER pad until

the display time disappears.

RemoteControlSignal Receiver

Remote Control

/;S_To ensure proper operation, aim the

remote control at the signal receiver

on the air conditioner.

/TS_'Ilm remote control signal has a range

of up to 21 feet.

_ Make sure nothing is between the air

conditioner and the remote control

that could block the signal.

_ Make sure batmries are fresh and installed

correctly as indicated on the remote control.

GEAppliances.com

When the air conditioner is turned on, it will

automatically start in the last cool and fan

settings used.

Lights next to the touch pads on the air conditioner

control panel indicate the selected settings.

COOLMode

Use the COOLmode with HIGH (F3),MED (F2) or

LOW(F1) fan for cooling. Use the INCREASE •/

DECREASEY pads to set the desired temperature

between 60°F and 86°F in 1°F increments.

A thermostat is used to maintain the room

temperature. _i11ecompressor will cycle on and off

to keep the room at the set level of comforL Set dm

thermostat at a lower number and the indoor air

will become cooleE Set the thermostat at a higher

numix-r and the indoor air will become warmm:

NOTE:ff the air conditioneris off andis thenturnedon

whileset to COOL,it will take approximately3 minutes

for the compressorto startand coolingtobegin.

CoolingDescriptions

For Normal Cooling-Select the COOLmode mad

HIGH (F3)or MED (F2)fan with a middle set

temperature.

ForMaximum Coolino-vSelect the COOLmode

and HIGH (F3)Pan with a lower set temperature.

For Quieter &Nighttime Cooling-Select the

COOLmode mad LOW(F1) Pan with a middle set

temperature.

NOTE:If youswitch from a COOLsettingto OR:or to

a fansetting, wait at least3 minutesbeforeswitching

back to a COOLsetting.

FAN Mode

Use dm FAN at HIGH (F3),MED (F2)or LOW (F1)to

provide air circulation and filtering without cooling.

Since Pan only" settings do llOt provide cooling,

a temperature setting will llOt be displayed.

VentControl

The vent COlltrol is located above the control

panels.

When set at CLOSE, only" the air inside the room

will be circulated and conditioned. When set at

OPEN, some inside air is exhausted outside.

Toopen the vent, pull the lever toward yea

TOclose it, push it in.

Air Direction -Side-to-Side

The side-to-side air direction is ad.jus_d by moving

the lever to the left or right.

Air Direction -Up and Down

Fingertip pre_ure on the horizontal louvers

adjusts the air direction up or down. (onsomemodels)

Aboutthecontrolsonthe air conditioner_odels with controlknobs.

Features and appearance will va_

OFF

HIGHOcIIGH

FAN COOL

LOW MED

FAN OOL

LOW

COOL

OFF

.0 i.

FAN 00L

LOW .OW

FAN COOL

OMODECONTROLS

Yourmodel will have one of the above type controls.

OTEMPCONTROLS

Yourmodel will have one of the above type controls.

Controls

oMode Controls

HIGHCOOL,MEDCOOLand LOWCOOL @

provide cooling with different i_anspeeds.

FANmttings provide air circulation and

filtering without cooling.

NOTE:If youmovethemodecontrolfroma coolsetting

toOFFortoafansetting,waitat least3 minutesbefore

switchingbacktoa coolsetting.

Cooling Descriptions

ForNormal Cooling--SelectHIGHCOOLor MED

COOLwith the temp control at midpoint.

For Maximum Cooling--Select HIGH COOL with the

temp control at the highest number available on

your knob.

ForQuieter& NighttimeCooflng--Select LOW COOL

with the temp control at midpoint.

TempControls

The temp control is used m maintain the

room temperature. _12qecompressor will

cycle on and offm keep the room at the

same level of comtort. When you turn the

knob m a higher numbel; the indoor air

will become cooler. Turn the knob to a lower

number and the indoor air will become

warmel:

GEAppliances.com

Additional controls and important information.

Energy Saver (on some models)

_i11e energy saver switch controls the fan.

ON--The fan and compressor cycle Olland off

together. 'I11isresults in wider variations of room

mmperature and humidity: Normally" used when

the room is unoccupied.

OFF--The fan nms all the time, while the

compressor cycles on and off

This switch must be set at OFFin order to use the

fhn settings (on the mode control).

Vent Control

The vent control is located above the

control knobs.

When set at CLOSE,only"the air inside the room will

be circulated and conditioned. When set at OPEN,

some inside air is exhausted outside.

Toopen the vent, pull the lever toward you.

Toclose it, push it in.

Air Direction -Side-to-Side

On some models, the side-to-side air direction is

adjusted by moving the lever to the left or right. CIRCULAIRE(on some models)

For fixed side-to-side air direction, set the

Circulaire switch to ON until the desired air

direction is obtained, then move it to OFF.

For continuous side-to-side air circulation (cool

settings only), set the Circulaire switch to ON.

ClRCULAIRE

OFF _ON

Air Direction -Up and Down

Fingertip pressure on the horizontal louvers adjusts

the air direction up or down. (onsomemodels)

Careand cleaningoftheair conditioner.

Grille and Case

Turn tbe air conditioner off and remove the To clean, use water and a mild detergent. Do llOt

plug from the wall outlet before cleaning, use bleach or abrasives.

OutdoorCoils

_12qecoils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged

with dirt or soot, they may be professionally steam

cleaned, a service available through your GE

service outlet.

AirFilter

The air filter behind the front grille should be

checked and cleaned at least every 30 days or

more often if necessary.

Toremove:

[] Open the inlet grille upward by pulling out

the bottom of the inlet grille.

] Using the tab, pull up slightly on the filter

to release it and pull it dowql.

Clean the filter with ,a-arm, soapy water. Rinse and

let the filter diT before replacing it.

CAUTION:DONOToperatetheairconditionerwithouta

filterbecausedirtandlintwillclogit andreduceperformance.

Preparingtoinstall the air conditioner.

Read these instructions completely and carefully.

BeforeYouBegin

NOTE TOINSTALLER:Leave these instructions with

the air conditioner after installation is completed.

NOTE TOCONSUMER:Keep this Owner's Manual

and Installation Instructions for future use.

IMPORTANT NOTES:

For personal safe_ this air conditioner must be

properly grounded.

It is important to have the wall outlet and circuit

checked by a qualified electrician if there is any

doubt as to whether a proper ground exists.

_CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present

special problems--consult a qualified

electrician.

Follow National Electric Codes (NEC)and/or local

codes and ordinances.

ElectricalRequirements

Some models require 115/120-volt a.c.,

60 Hz grounded outlet protected with a

15-amp time delay fhse or circuit breaker:

32qe3-prong grounding plug minimizes the

possibility of electric shock hazard. K the wall oudet

you plan to use is only"a 2-prong outlet, it is your

responsibility to have it replaced with a properly"

grounded 3-prong wall outlet.

protected with a time delay fuse or circuit

breakeE These models should be installed

on their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

ToolsYouWillNeed

_;_;Phillips-head screwdriver

N Flat-blade screwdriver

/;;5Ruler or tape measure

U_Scissors or knife

_ Pencil

_ Level

WindowInstallationInstructions.

Parts Included

Left

accordion

panel

Top mounting rail

seal strip

Window

sash seal

w,2 am;° k

Frame guide (2)

Window locking

bracket

,Sill support (2)

Right

accordion

panel

Type A (16) Type B (3) Type C (5)

Nut (2)

Bolt(2)

Other manuals for AGM06

This manual suits for next models

Table of contents

Other GE Air Conditioner manuals

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual