GAMA Electronics RF24V1C User manual

RF24V1C

Instruction Manual

WWW.GAMAINC.COM

Included in this Kit:

(1) RF24V1C Receiver

(1) 2-Button Transmitter *Image shown with standard transmitter*

- 2-Button Rechargeable Transmitter GKF-WPTX-2

Available accessories:

- Package of A23 12V Alkaline Batteries A23-6

- 2-Button Waterproof Transmitter KF340-2WP

The RF24V1C is an RF receiver operating at a fixed frequency of 340 MHz. The receiver operates from 24VDC and

provides one isolated form C relay contact (normally open and normally closed contacts with one common). Up to

twelve, two button keyfob transmitters can be used to activate the receiver's relay. The relay can be configured to

function as a latching relay or momentary relay. Each transmitter has a unique address that is transmitted when a

button is pressed. A "program" button is provided on the receiver to program the transmitter(s) address into the

receiver's memory. The relay mode (latching or momentary) is programmed into the receiver's memory during the

programming process. An LED on the receiver indicates the receiver's programming status and illuminates when the

relay is energized. The receiver is encased in a small, waterproof enclosure. The typical operating range between

receiver and transmitter is up to 100 feet.

"Latching" vs. "momentary" relay operating modes: When the receiver is configured for "latching" mode, the relay will

energize when the "UP" button is pressed on the keyfob. The relay will remain energized until the "DOWN" button on

the keyfob is pressed. If multiple keyfobs are used any keyfob can energize the relay and any keyfob can de-energize

the relay. When the receiver is configured for "momentary" mode the relay will energize and remain energized as

long as the "UP" button is pressed on the keyfob. The "DOWN" button on the keyfob transmitter has no effect in this

mode

Maximum ratings:

Power for the receiver can be in the range of 21 to 24Vdc. The receiver is reverse polarity protected.

The relay contacts are electrically isolated from the DC power leads.

The relay contacts are rated at 10 Amps @ 30Vdc or 120/240Vac.

Power consumption:

10mA when the relay is de-energized. 45mA when the relay is energized

Dimensions:

1.65" X 1.46" X 1.04". The flexible whip antenna extends 3" from the enclosure.

Net weight 2.35 oz. . Page 1 REV A 07/07/20

- 340MHz Long Range Antenna LRA-340 *See Page 3 for Setup*

- 2-Button Keyfob Transmitter KF340-2

- Clear Protective Transmitter Pouch ZLB-67

Programming Instructions

Each transmitter has its own unique internal address along with the data as to which button is pressed and transmitted.

The receiver needs to be programmed to respond only to the specific transmitter it is intended to operate with. The

following steps configure the receiver to operate with a particular transmitter. Up to 30 transmitters can be programmed

to one receiver. Please read the entire programming procedure before starting. When the receiver enters program

mode, all previous transmitter addresses that were programmed will be erased from the receiver's memory.

1. Locate the pushbutton labeled "PROGRAM" on the receiver. Press and hold this button until the red LED next to the

program button illuminates (approximately 3 seconds). The receiver is now in the transmitter program mode. Release

the button. At this point all previously programmed transmitter addresses are erased from the receiver's memory.

2. To configure the receiver for a latching output, go to Step 4.

3. To configure the receiver for momentary output, press and release the UP button on the transmitter and verify that the

red program LED

extinguishes and then illuminates (blinks once). Proceed to Step 5.

4. To configure the receiver for latching output, press and release the DOWN button on the transmitter and verify that

the red program LED extinguishes and illuminates (blinks once).

5. Repeat previous step for additional transmitters that will operate with this particular receiver. The red LED on the

receiver will extinguish and illuminate (blink) once for the first transmitter being programmed, twice for the second, three

times for the third, etc. The receiver will not respond to transmitters that have already been programmed. The first

transmitter that is programmed determines the receiver’s relay operating mode.

6. The receiver will return to normal mode if no transmitter buttons are pressed for 5-seconds. The red LED on the

receiver will blink rapidly, then extinguish. The receiver is now in the normal mode of operation. This completes the

programming instructions. The receiver will retain all of its programming even when power is removed.

WWW.GAMAINC.COM

Page 2 REV A 07/07/20

RF24V1C

Instruction Manual

RF24V1C

GAMAINC.COM

COM

PROGRAM

Programming Switch

Programming LED

Power Terminals

Isolated Output Contacts

Long Range

Antenna Jack

WWW.GAMAINC.COM

Page 3 REV A 07/07/20

To Add Long Range Functionality

The remote control system is equipped with an internal antenna. The expected range in normal conditions is

approximately 100 feet. When additional range is needed, or if the control is placed locations adverse to RF signal

reception, a long range antenna can be added to the system. GAMA Electronics long range antenna, part number LRA-

340, replaces the internal antenna on the system. In normal operating conditions expected range is greater than 500 feet.

If the long range option is purchased with the system, this modification will be made prior to shipment.

To add long range functionality:

1. Plug long range antenna (Part number LRA-340) into the long range antenna jack.

2. Clip the Long Range Antenna Bypass Wire (This will deactivate the internal antenna)

NOTE: It is recommended that you cover the exposed wires with RTV silicone sealant.

NOTE: ONCE THE LONG RANGE MODIFICATIONS HAVE BEEN MADE TO THE SYSTEM THEY CANNOT

BE REVERSED.

Wiring Diagram

RF24V1C

Instruction Manual

PROGRAM

COM

RFR12V1C

GAMAINC.COM

24V DC POWER

SOURCE

Isolated Output Contacts - Independent from the power source

NC - Normally Closed Contact

This terminal is connected to the common

until the receiver is activated by the transmitter

COM-Common

This terminal should be connected to the AC or DC

power that is being switched.

NO - Normally Open Contact

This terminal is connected to the common

when the receiver is activated by the transmitter

Insert Long Range Antenna HereProgram Switch

WWW.GAMAINC.COM

Page 4 REV A 07/07/20

Troubleshooting

All remote-control systems shipped by GAMA Electronics are 100% functionally tested just prior to shipment.

If your RF remote control system does not work out of the box, stops working or functions intermittently please take the

following steps to resolve common issues. Please note that you must be 2-3 feet away from the receiver when operating

the remote control. Operating within 2-3 feet may result in no operation or intermittent operation.

1. Replace the A23 12V Battery in the transmitter

· The remote control can activate during shipping and drain the battery that is installed in the control. We

send a replacement battery with the system if this occurs.

2. Check the voltage supply at the receiver

· The receiver is designed to function at 10-15VDC. Voltage on the (+) and (-) terminals on the control

should be within this range.

3. Reprogram the remote control

· If the system is non-functional try to reprogram the remote control. The program may not have taken

during the programming process or the program button may have been pressed. If the program button is

pressed the memory of the remote controls programed to the receiver are erased.

4. Listen and look for functionality on the receiver.

· The LED that is used for programming the system will illuminate when the receiver is activated. You will

also hear a “click” when the internal relays engage. If you can see the LED illuminate and you hear the

relay “click” the issue is most likely in the wiring or device being controlled.

5. Add a long-range antenna

· If the receiver is in an area that is averse to the reception of an RF signal, such as near a motor or in a

metal casing, a long-range antenna may solve the issue. Connect the antenna per the instructions on

page 3 and mount the antenna in an exposed area away from any motor.

RF24V1C

Instruction Manual

This manual suits for next models

Table of contents

Other GAMA Electronics Receiver manuals

GAMA Electronics

GAMA Electronics RF24V-1PR-ASL User manual

GAMA Electronics

GAMA Electronics RF340-4PR-ASL User manual

GAMA Electronics

GAMA Electronics RF12V-2PR-ASL User manual

GAMA Electronics

GAMA Electronics RF120VPRDC User manual

GAMA Electronics

GAMA Electronics RF120VPRDC User manual

GAMA Electronics

GAMA Electronics RFR12V1C User manual

GAMA Electronics

GAMA Electronics RFR24VPRWP User manual

GAMA Electronics

GAMA Electronics RF340-DRC User manual

GAMA Electronics

GAMA Electronics RF12V1PR-LS-NIS User manual

GAMA Electronics

GAMA Electronics RF12V1PR-LS User manual

GAMA Electronics

GAMA Electronics RF24V1PR-ASL-NIS User manual

GAMA Electronics

GAMA Electronics RF340-100APR User manual

GAMA Electronics

GAMA Electronics RF240V-2WP-NIS User manual

GAMA Electronics

GAMA Electronics LRF24V1PR-LS User manual

GAMA Electronics

GAMA Electronics RF340-4PR-ASL-NIS User manual

GAMA Electronics

GAMA Electronics RF340-400APR-WPTX User manual

GAMA Electronics

GAMA Electronics RF120V-2WP User manual

GAMA Electronics

GAMA Electronics RF12V-2-ASL-NIS User manual

GAMA Electronics

GAMA Electronics LRF240V-2WP User manual

GAMA Electronics

GAMA Electronics RF24V-2-ASL User manual

GAMA Electronics

GAMA Electronics RF12V-2-ASL User manual

GAMA Electronics

GAMA Electronics RF340-400APR User manual

GAMA Electronics

GAMA Electronics T-SC-12V-NIS User manual

GAMA Electronics

GAMA Electronics RF120VPRDC-NIS User manual

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual