Fujitsu N7100 Configuration guide
1
N7100 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
N7100 CONSUMABLE REPLACEMENT
AND CLEANING INSTRUCTIONS
CG00002-291401
N7100CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
2
Brake Roller Pick Roller
CONSUMABLES LIST
Description Qty Life Fujitsu P/N
BrakeRoller 1
Pick Roller 1 200,000 PA03706-0001
Note: The Brake Roller and Pick Roller are included when
ordering part number PA03706-0001
3
N7100 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
CHECKING THE LIFE OF THE CONSUMABLES
1. On the [Main Menu] or [Job Menu] window, press
the [ConsumableAlert] button.
The [Consumable Alert] window appears.
2. Check which part needs to be replaced and press
the[OK]button.
Partswhose[UsageCounter]valueisbigger than the
[Replaceat]valueshouldbe replaced.
Thevalueof[Usage Counter] istheexactnumberof
scannedsheets.
3. Replace the part.
Refertothefollowing:
Replacing the Roller Set.
HINT
The [Consumables Alert] button on the [Job Menu] window can be shown
by pressing
N7100CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
4
REPLACING THE ROLLER SET
TheRollerSetismadeupof the
brakerollerandthepickroller.The
procedureforreplacingeachroller
isasfollows.
1. Turn off the scanner power and wait
for at least 15 minutes.
2. Unplug the power cable from the AC outlet.
3. Remove any documents from the ADF paper chute.
4. Pull the cover release catch toward you, place
your hands at both sides of the LCD cover, and
open the LCD cover.
5. Replace the brake roller.
1. Open the cover of the brake roller.
Be careful that the LCD cover does not shut on your fingers.
Cover
Hold both ends of the cover of the brake roller, and open it in the direction of the arrow.
5
N7100 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE ROLLER SET (CONT.)
2. Remove the shaft.
Lifttherightsideof the rollerfirst,thenpullouttheshaft from the
slotonthe left.
Brake Roller
Shaft
3. Remove the brake roller from its shaft
Shaft
Brake Roller
4. Attach a new brake roller on the shaft.
Insert theprotrusionon theshaftintotheslot.
Shaft
Protrusion
Slot
Brake Roller
N7100CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
6
REPLACING THE ROLLER SET (CONT.)
5. Install the brake roller with the shaft on the scanner.
Fit the left end of the shaft in the slot, then install the rest of the shaft in
place.
Brake Roller
Shaft
6. Close the cover of the brake roller.
ATTENTION
Make sure that the shaft is attached properly. If it is not correctly attached,
document jams and other feeding errors may occur.
ATTENTION
Make sure that the shaft is attached properly. If it is not correctly attached,
document jams and other feeding errors may occur.
7
N7100 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
REPLACING THE ROLLER SET (CONT.)
1. Open the sheet guide.
Slide the side guides all the way, and pull the sheet guide open from the
dip.
2. Rotate the lock release tab on the shaft in the direction of the
arrow.
Dip
Side Guides
Sheet Guide
Lock Release Tab
N7100CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
8
3. Remove the pick roller.
Slightly lift the Lock release tab of the shaft (by approximately 5 mm),
slide the shaft to the direction of the arrow below, and lift it up all the
way.
Lock Release Tab
ATTENTION
Becareful not totouchthegear near the lockreleasetab on the shaftas
it contains grease.
REPLACING THE ROLLER SET (CONT.)
9
N7100 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
4. Install a new pick roller on the scanner.
Insert the left end of the shaft into the slot of the scanner, and lower
the other end gradually.
Pick Roller
5. Rotate the lock release tab on the shaft in the direction
of the arrow.
Lock Release Tab
ATTENTION
Make sure that the pick roller is installed properly. Otherwise, paper
jams or other feeding errors may occur.
REPLACING THE ROLLER SET (CONT.)
N7100CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS
10
6. Close the sheet guide.
Make sure that both ends of the sheet guide are locked firmly.
7. Close the LCD cover.
You should hear a click.
REPLACING THE ROLLER SET (CONT.)
Be careful that the LCD cover does not shut on your fingers.
8. Connect the power cable, and turn on the scanner.
9. Reset the Roller Set usage counter.
After part replacement, the usage counter can be reset to return the part
status to normal.
1.Select [Usage Status] under [Status Details].
The [Usage Status] window appears.
2.Press the [Clear] button for the part replaced.
The counter reset confirmation window appears.
3.Press the [OK] button.
Other manuals for N7100
3
Table of contents
Other Fujitsu Scanner manuals
Fujitsu
Fujitsu ScanPartner Manual
Fujitsu
Fujitsu Fi-5110EOX2 - ScanSnap! - Document Scanner User manual
Fujitsu
Fujitsu S510M - ScanSnap - Document Scanner Configuration guide
Fujitsu
Fujitsu fi-6800 User manual
Fujitsu
Fujitsu Fujitsu fi-5950 Manual
Fujitsu
Fujitsu FI-4860C2 User manual
Fujitsu
Fujitsu PA03360-B505 - ScanSnap S500 Manual
Fujitsu
Fujitsu M3096EX Manual
Fujitsu
Fujitsu ScanSnap S1100 User manual
Fujitsu
Fujitsu M3097DG Installation and operation manual
Fujitsu
Fujitsu ScanSnap fi-5110EOX Manual
Fujitsu
Fujitsu ScanSnap S1300 User manual
Fujitsu
Fujitsu ScanPartner FI-4110CU Manual
Fujitsu
Fujitsu S510M - ScanSnap - Document Scanner User manual
Fujitsu
Fujitsu S510M - ScanSnap - Document Scanner Manual
Fujitsu
Fujitsu PA03586-B205 User manual
Fujitsu
Fujitsu ScanSnap fi-5110EOX User manual
Fujitsu
Fujitsu fi-60F User manual
Fujitsu
Fujitsu fi-60F Manual
Fujitsu
Fujitsu FI-5900C Configuration guide
