Fujitsu M3092DC User manual
2-
M3092DC Image Scanner
OPERATION GUIDE
C150-E131-02EN
Top
M3092DC Image Scanner Operation Guide
FOR SAFE OPERATION
Treatment of This Manual
Since this manual contains important information for using the M3092DC, read it
thoroughly before using the product. Use the M3092DC only after thoroughly reading and
understanding especially the section "Important Alert Messages" in this manual. Keep this
manual handy, and store it carefully.
Notice to
American Users Federal Communications Commission
Radio Frequency Interference Statement
Notice: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Adjust or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from the
circuit the receiver is connected to.
•Consult your dealer or an experienced radio/TV technician for help.
FCC warning: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.
M3092DC Image Scanner Operation Guide
Notice to
American Users
cont.
Notes
•The use of a non-shielded interface cable with the referenced device is
prohibited. The length of the parallel interface cable must be 3 meters
(10 feet) or less. The length of the serial interface cable must be 15
meters (50 feet) or less.
•The length of the power cord must be 3 meters (10 feet) or less.
Notice to
Canadian Users This digital apparatus does not exceed the class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numériqué n'émet pas de bruits radioélectnques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Comunications du Canada.
Notice to
German Users Bescheinigung des Herstellers/Importeurs
Hiermit wird bescheinigt, daß der/die/das
•M3092DC in Übereinsstimmung mit den Bestimmungen der
•AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundespost wurde
das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung
zur Überprüfung der Serie auf Einhaltung der Bestimmungen
eingeräumt.
•Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991:
Der höchste Schalldruckpegel beträgt 70 dB (A) order weniger
gemäß ISO/7779.
M3092DC Image Scanner Operation Guide
Trademark Acknowledgment
Fujitsu is a registered trademark of Fujitsu Limited.
Second Edition, October 1999
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media
without the express written permission of Fujitsu Limited.
All Rights Reserved, Copyright FUJITSU LIMITED 1999
M3092DC Image Scanner Operation Guide i
Preface
Thank you very much for your purchase of the M3092DC Image Scanner.
The M3092DC Image Scanner can read very fine color images.
As this manual explains the basic handling of the scanner, read it carefully
to use the scanner properly.
In this manual, the MicrosoftWindows NTOperating System is
referred to as Windows NT, the MicrosoftWindows 95Operating
System is referred to as Windows 95, and the MicrosoftWindows 98
Operating System is referred to as Windows 98.
Microsoft, Windows, and Windows NT are registered trademarks of
Microsoft Corporation of the U.S. in the United States and other countries.
Other company names or product names appearing in this manual are
trademarks or registered trademarks of individual companies.
ii M3092DC Image Scanner Operation Guide
Important Notes to Users
Every user is requested to use this product including the manuals and
software supplied with the product at the user's own responsibility.
Fujitsu assumes no liability with respect to any damage or loss caused to
data as the result of using this product.
Please understand that the warranty range for failure of this product will
never exceed the amount of money paid by the user for the product.
Fujitsu prohibits any user from using software supplied with this product
or any other update software for this product for any purpose other than
incorporation into this product. Fujitsu also prohibits any user from
reworking or disassembling such software.
M3092DC Image Scanner Operation Guide iii
Conventions for Alert Messages
Alert messages
This manual uses alert messages to prevent users and bystanders from
being injured or from suffering damage to their property. An alert
message consists of an alert signal and alert statements. The alert signals
and their meanings are as follows.
WARNING This indicates a hazardous situation that could
result in serious personal injury if the user
does not perform the procedure correctly.
CAUTION This indicates a hazardous situation that could
result in minor or moderate personal injury if
the user does not perform the procedure
correctly. This alert signal also indicates that
damage to the products or other property may
occur if the user does not perform the
procedure correctly.
In addition to the above-cited signals, the
following symbols are also used to provide
detailed information concerning injury or
damage:
Electric shock The symbol marked with
indicates a warning or caution.
The concrete meaning of an alert
is illustrated in the symbol. (The
example at left indicates caution
against an electric shock.)
iv M3092DC Image Scanner Operation Guide
Disassembly The symbol marked with
indicates what must not be done
(prohibited action). The concrete
meaning of the action is
illustrated in the symbol. (The
example at left indicates the
prohibition of disassembly.)
Plug The symbol marked with
indicates what must be observed.
The concrete meaning of the
action is illustrated in the symbol.
(The example at left directs the
operator to disconnect the power
plug from the outlet.)
M3092DC Image Scanner Operation Guide v
Important Alert Items
Important Alert Messages
Important alert messages applicable to the M3092DC Image Scanner are
listed below. Observe these directions for safe operation of the scanner.
Alert concerning power supply
WARNING
Prohibited −Do not insert the AC adapter to any outlet other than one dedicated to
15 A at 100 VAC. Do not make a starburst connection.
It could result in a fire or electric shock.
−Do not damage, break, or process the power cord. Do not put a heavy
item on, pull, or forcibly bend it.
It could result in a fire or electric shock.
−Use only the power cord (AC adapter) supplied with the scanner. Do
not use an extension cord.
It could result in abnormal heat or a fire.
−Do not use the power cord or AC adapter if it is damaged or loose in
connection with the outlet.
It could result in a fire or electric shock. Ask your sales agency or
Fujitsu Limited for repair.
vi M3092DC Image Scanner Operation Guide
Electric
shock −Disconnect the AC adapter from the outlet before connecting an
interface cable or optional product.
Failure to do so could result in an electric shock.
−Do not handle the AC adapter with wet hands when connecting or
disconnecting it.
It could result in an electric shock.
Direction −If the AC adapter or outlet is covered with dust, clean it well with a
dry cloth.
Failure to do so could result in a fire.
Plug −If one of the following occurs, promptly stop using the scanner and
disconnect the AC adapter from the outlet, then call your sales agency
or Fujitsu Limited:
−The scanner generates smoke or the outside of the scanner is
extraordinarily hot.
−The scanner generates an abnormal sound.
−Water enters the inside of the scanner.
Failure to do so could result in a fire.
−In case of thunder, disconnect the AC adapter from the outlet.
Failure to do so could result in damage to the scanner or other
property of the customer.
Other manuals for M3092DC
2
Table of contents
Other Fujitsu Scanner manuals
Fujitsu
Fujitsu fi 5750C - Document Scanner Configuration guide
Fujitsu
Fujitsu ScanSnap S1300i User manual
Fujitsu
Fujitsu fi-4340C Manual
Fujitsu
Fujitsu fi-4110EOX2/ScanSnap Configuration guide
Fujitsu
Fujitsu i-4990C Manual
Fujitsu
Fujitsu ScanSnap iX1500 Assembly instructions
Fujitsu
Fujitsu SV600 Assembly instructions
Fujitsu
Fujitsu Scan Snap iX 500 User manual
Fujitsu
Fujitsu fi-5530C - Document Scanner Manual
Fujitsu
Fujitsu 5110C - fi - Document Scanner User manual
Fujitsu
Fujitsu fi-6140Z User manual
Fujitsu
Fujitsu M3096NT User manual
Fujitsu
Fujitsu FI-5015C User manual
Fujitsu
Fujitsu S500M - ScanSnap - Document Scanner User manual
Fujitsu
Fujitsu S510M - ScanSnap - Document Scanner Manual
Fujitsu
Fujitsu M4099D Configuration guide
Fujitsu
Fujitsu fi-65F User manual
Fujitsu
Fujitsu fi 5750C - Document Scanner Configuration guide
Fujitsu
Fujitsu C150-E146-02EN Manual
Fujitsu
Fujitsu FI-5900C Use and care manual
