FSR HD-HU-SP-TX User manual
HD-HU-SP-TX / HD-HU-SP-RX
HDBaseT 2.0 and USB Transmitter / Receiver
244 Bergen Boulevard, Woodland Park, NJ 07424 •Tel 973-785-4347 •
FAX 973-785-3318 •Web: www.fsrinc.com
43154 LIT1639A
User Manual
Important Safety Instructions
Contents are subject to change without notice
Warnings
To reduce the risk of fire, electric shock or product damage:
1. Do not expose this device to
rain, moisture, dripping or
splashing and that no objects
filled with liquids, such as vases,
shall be placed on the unit.
6. Clean this device only
with dry cloth.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other device
(including amplifiers) that produce
heat.
5. Do not place sources of open
flames, such as lighted candles,
on the unit.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect cables and
cords from being walked
on or pinched particularly
at plugs.
9. Only use
attachments/accessories
specified by FSR.
10. Refer all servicing to
qualified service
personnel.
2
Table of Contents
Overview .................................................................................................. 4
Features ................................................................................................... 5
Package Contents.................................................................................... 6
Typical Application.................................................................................... 7
Panel Layout ............................................................................................ 8
Hardware Installation.............................................................................. 16
USB Connections ................................................................................... 18
RS-232 Control and Firmware Updates ................................................. 20
Specifications ......................................................................................... 21
Overview
Based on HDBaseT 2.0 Technology, these true HDBaseT 5-Play devices
transmit HD Video (up to 4k @60hz.), Audio, Bi-Directional Control (IR &
RS-232), Ethernet, and Bi-directional Power via 1 CAT-6A shielded cable up to
100 Meters.Long Reach Mode and increases the usable CAT6A shielded cable
length of up to150m / 492ft with up to a 1920x1080p HD video@60Hz / 24bit
Deep Color signal.
The units also carry two-way USB 2.0 on the same cable as well as an analog
audio input on the Transmitter and analog stereo audio output on the Receiver.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance
4
Features
True HDBaseT 5-Play
HDMI transmissions using single cable Cat5e cable under recommended
conditions:
90m/295ft: 4096 x 2160 video@30Hz / 24bit True Color with Chroma
subsampling color palette 4K@60Hz 4:2:0
- 100m/328ft: 1920x1080p HD video@60Hz / 36bit Deep Color
Via Cat6/6a/7 cables:
100m/328ft: 4096 x 2160 video@30Hz / 24bit True Color with
Chroma subsampling color palette 4K@60Hz 4:2:0
150m/492ft: 1920x1080p HD video@60Hz / 24bit Deep Color (Long
Reach Mode)
Bi-directional PoH (Power over HDBaseT) allowing a single power supply to
power both transmitter and receiver
Fully compliant with HDMI 1.4, and compatible with HDMI 2.0 (4K 60Hz with
4:2:0 coding)
HDCP 2.2 compliance
One analog stereo audio pass through from Transmitter in to Receiver out
over HDBaseT
Bi-directional USB pass through , USB Host/Device adjustable in both
Transmitter and Receiver
Built in 100MBase-T Ethernet Switch integral to both Transmitter and
Receiver
Audio & Video, Power, Ethernet, RS232 and IR pass-through over HDBaseT
Additional Phoenix connection power port
Dual function RS232 port for firmware update
Locking DC power connector
Cable termination follows IEEE-568B standards
5
Package Contents
One HD-HU-SP-TX Transmitter
One HD-HU-SP-RX Receiver
One Power Supply 12VDC / 2A
Two 3.5mm Phoenix Male Connectors (2 Pin)
Two 3.5mm Phoenix Male Connectors (3 Pin)
Two IR Emitters
Two Wide-band IR Receivers (30KHz~50KHz)
Two Mounting Brackets (Pairs)
6
Typical Application
NOTE: It is only necessary to power one side (Tx or Rx)
7
Panel Layout
Transmitter
Front Panel
No.
Name
Description
1 SET
Enables/disables the Long Reach Mode,
RS232 updates /pass-through the device
Choose USB Device or USB Host mode
2 Power LED ON: The transmitter is powered on
OFF: The transmitter is powered off
3 Status LED
Flashing Slowly:
The transmitter is working properly
OFF: The transmitter is not working properly
4 HDCP LED
ON: HDCP video is being transmitted
Flashing Quickly: Non-HDCP video is being
transmitted
5 Link LED ON: HDBT link is normal
Blinking/OFF: No HDBT Link or link is unstable
8
SET DIP switch Settings
The SET DIP switch is capable of setting the RS232 firmware update or RS232
pass through function, choosing USB device or USB Host mode and
enabling/disabling the Long Reach Mode.
NOTE: SET switches that are marked in grey indicate the switch can be in any
position.
The first switch is used for controlling the RS232:
RS232 pass through
RS232 firmware update
9
The second switch is used for controlling the USB HOST/DEVICE mode on
the Rx and Tx Units:
NOTE: The second switch must be in the same position on both the Transmitter
and Receiver:
Set Tx Unit to be USB Host and Rx Unit to be USB Device
Note: Reboot the device to make the change effective.
Set Rx Unit to be USB Host and Tx Unit to be USB Device
Note: Reboot the device to make the change effective.
The third switch is used for controlling the Long Reach Mode. This increases
the usable CAT6A shielded cable length of up to150m/492ft when using up to a
1920x1080p HD video@60Hz / 24bit Deep Color signal.
Long Reach Mode OFF
(Set BOTH the Transmitter and Receiver to "OFF", then remove power and
reapply to activate the new setting)
Long Reach Mode ON
(Set BOTH the Transmitter and Receiver to "ON", then remove power and reapply
to activate the new setting)
10
This manual suits for next models
1
Table of contents
Other FSR Receiver manuals
