Frigidaire 137135100B User manual

Installation Instructions

Gas & Electric Dryer

Instructions d’Installation

Sécheuse à Gaz ou Électrique

Instrucciones de Instalación

Secadora a Gas y Eléctrica

www.frigidaire.com P/N 137135100B (0903)

Important Safety Instructions ................................................2

Pre-installation Requirements ................................................2

Installation Requirements .................................................. 3-7

Installed Dimensions .............................................................8

Installation Instructions ................................................... 9-13

Reversing door.............................................................. 14-15

Accessories/Replacement parts............................................16

Français ..............................................................................17

Español...............................................................................32

Notes..................................................................................47

Table of Contents

Important Safety Instructions

Recognize safety symbols, words and labels

Safety items throughout this manual are labeled with a

WARNING or CAUTION based on the risk type as described:

- RISK OF FIRE - Read all of the following instructions before installing and using this appliance:

Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with•

rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage

container or make materials inaccessible to children.

Clothes dryer installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.•

Install the clothes dryer according to the manufacturer’s instructions and local codes.•

The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the National•

Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.

The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National Fuel Gas•

Code ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000.

The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for HOME USE•

only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

Do not install a clothes dryer with ﬂexible plastic venting material. Flexible venting materials are known to collapse, be eas-•

ily crushed and trap lint. These conditions will obstruct clothes dryer airﬂow and increase the risk of ﬁre.

The instructions in this manual and all other literature included with this dryer are not meant to cover every possible•

condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and

maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.•

Do not touch any electrical switch; do not use any phone in your building.•

Clear the room, building or area of all occupants.•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.•

If you cannot reach your gas supplier, call the ﬁre department.•

Save these instructions for future reference.

Pre-Installation Requirements

This symbol alerts you to situations that

may cause serious body harm, death or property damage.

This symbol alerts you to situations that may

cause bodily injury or property damage.

For your safety the information in this manual must be followed to minimize the risk of ﬁre or explosion or to

prevent property damage, personal injury or loss of life. Do not store or use gasoline or other ﬂammable vapors and liquids in

the vicinity of this or any other appliance.

Tools and materials needed for installation:

Adjustable pliers•

Phillips, straight, & square bit screw-•

drivers

Adjustable wrench•

Pipe wrench for gas supply (gas dryer)•

LP-resistant thread tape (for natural•

gas or LP supply, gas dryer)

Carpenter’s level•

External vent hood•

4-inch (10.2 cm), rigid metal or semi-•

rigid metal exhaust duct work

3-wire or 4-wire 240 volt cord kit•

(electric dryer)

4 in. (10.2 cm) clamp•

Gas line shutoff valve (gas dryer)•

½ NPT union ﬂare adapters (x2) and•

ﬂexible gas supply line (gas dryer)

Metal foil tape (not duct tape)•

This dryer is internally grounded to neutral unless it was manufactured for sale in Canada. Grounding through

the neutral link is prohibited for: (1) new branch circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas

where local codes do not permit grounding through the neutral.

Electrical System Requirements

Electrical requirements for electric dryer

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately fused

circuits for washer and dryer. DO NOT operate a washer and a dryer on the same circuit.

POWER SUPPLY - 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current.

3-WIRE POWER SUPPLY CORD KIT (not supplied)

OUTLET RECEPTACLE - NEMA 10-30R or NEMA 14-30R receptacle to be located so the power supply cord is accessible when the

dryer is in the installed position.

GROUNDING CONNECTION - See “Grounding requirements” in Electrical Installation section.

The dryer MUST employ a 3-conductor power supply cord

NEMA 10-30 type SRDT rated at 240 volt AC minimum,

30 amp, with 3 open end spade lug connectors with

upturned ends or closed loop connectors and marked

for use with clothes dryers. For 3-wire cord connection

instructions see ELECTRICAL CONNECTIONS FOR A

3-WIRE SYSTEM.

4-WIRE POWER SUPPLY CORD KIT (not supplied)

The dryer MUST employ a 4-conductor power supply cord

NEMA 14-30 type SRDT or ST (as required) rated at 240

volt AC minimum, 30 amp, with 4 open end spade lug

connectors with upturned ends or closed loop connectors

and marked for use with clothes dryers. For 4-wire cord

connection instructions see ELECTRICAL CONNECTIONS

FOR A 4-WIRE SYSTEM.

Electrical requirements for gas dryer

CIRCUIT - Individual, properly polarized and grounded 15

amp. branch circuit fused with 15 amp. time delay fuse or

circuit breaker.

POWER SUPPLY - 2-wire, with ground, 120 volt, single phase,

60 Hz, Alternating Current.

POWER SUPPLY CORD - The dryer is equipped with a 120 volt

3-wire power cord.

GROUNDING CONNECTION - See “Grounding requirements”

in Electrical Installation section.

Grounding type

ll receptacl

ll receptacle

wer cord with

3-prong

ounded plug

Do not,

under

y cir

cumstances,

cut,

remo

ve,

or b

ypass th

ypass the

ounding pr

ong.

3-wire receptacle

(NEMA type 10-30R)

4-wire receptacle

(NEMA type 14-30R)

Because of potentially inconsistent voltage capabilities, the use of this dryer with power created by gas powered gen-

erators, solar powered generators, wind powered generators or any other generator other than the local utility company is not

recommended.

Dryers manufactured for sale in Canada have factory-

installed, 4-wire power supply cord (NEMA 14-30R).

Exhaust system requirements

If your present system is made up of plastic duct or metal foil

duct, replace it with a rigid or semi-rigid metal duct. Also,

ensure the present duct is free of any lint prior to installing

dryer duct.

Use only 4 inch (10.2 cm) diameter (minimum) rigid or ﬂexible

metal duct and approved vent hood which has a swing-out

damper(s) that open when the dryer is in operation. When

the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoid

restricting the outlet, maintain a minimum of 12 inches (30.5

cm) clearance between the vent hood and the ground or any

other obstruction.

Correct Incorrect

The following are speciﬁc requirements for

proper and safe operation of your dryer.

Gas supply requirements

1. Installation MUST conform with local codes, or in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1 (latest edition).

2. The gas supply line should be 1/2 inch (1.27 cm) pipe.

3. If codes allow, ﬂexible metal tubing may be used to

connect your dryer to the gas supply line. The tubing

MUST be constructed of stainless steel or plastic-coated

brass.

4. The gas supply line MUST have an individual shutoff valve.

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible

for test gauge connection, MUST be installed immediately

upstream of the gas supply connection to the dryer.

6. The dryer MUST be disconnected from the gas supply

piping system during any pressure testing of the gas

supply piping system at test pressures in excess of 1/2 psig

(3.45 kPa).

7. The dryer MUST be isolated from the gas supply piping

system during any pressure testing of the gas supply

piping system at test pressures equal to or less than 1/2

psig (3.45 kPa).

8. Connections for the gas supply must comply with the

Standard for Connectors for Gas Appliances, ANSI Z21.24.

- EXPLOSION HAZARD - Uncoated copper

tubing will corrode when subjected to natural gas, causing

gas leaks. Use ONLY black iron, stainless steel, or plastic-coat-

ed brass piping for gas supply.

- FIRE HAZARD - Failure to follow these in-

structions can create excessive drying times and ﬁre hazards.

- FIRE HAZARD - Do not install a clothes

dryer with ﬂexible plastic or metal foil venting materials.

Flexible venting materials are known to collapse, be easily

crushed and trap lint. These conditions will obstruct clothes

dryer airﬂow and increase the risk of ﬁre.

- FIRE HAZARD -

Do not allow combustible materials (for example: clothing,•

draperies/curtains, paper) to come in contact with exhaust

system. The dryer MUST NOT be exhausted into a chim-

ney, a wall, a ceiling, or any concealed space of a building

which can accumulate lint, resulting in a ﬁre hazard.

Do not screen the exhaust ends of the vent system, or use•

any screws, rivets or other fasteners that extend into the

duct to assemble the exhaust system. Lint can become

caught in the screen, on the screws or rivets, clogging the

duct work and creating a ﬁre hazard as well as increasing

drying times. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with duct tape. All male

duct pipe ﬁttings MUST be installed downstream with the

ﬂow of air.

- FIRE HAZARD -

Do not install ﬂexible plastic or ﬂexible foil venting mate-•

rial.

If installing semi-rigid venting, do not exceed 8 ft. (2.4 m)•

duct length.

- FIRE HAZARD - A clothes dryer must be

exhausted outdoors. Do not exhaust dryer into a chimney, a

wall, a ceiling, an attic, a crawl space or any concealed space

of a building. A clothes dryer produces combustible lint. If

the dryer is not exhausted outdoors, some ﬁne lint will be

expelled into the laundry area. An accumulation of lint in any

area of the home can create a health and ﬁre hazard.

- FIRE HAZARD - Exceeding the length of

duct pipe or number of elbows allowed in the “MAXIMUM

LENGTH” charts can cause an accumulation of lint in the ex-

haust system. Plugging the system could create a ﬁre hazard,

as well as increase drying times.

The dryer must be connected to an exhaust outdoors.

Regularly inspect the outdoor exhaust opening and remove

any accumulation of lint around the outdoor exhaust opening

and in the surrounding area.

Exhaust system requirements, continued

Number of 90° turns

MAXIMUM LENGTH

of 4” (10.2cm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

4”

(10.2cm) louvered

2.5”

(6.35cm)

0 64 ft. (19.5 m) 48 ft. (14.6 m)

1 52 ft. (15.9 m) 40 ft. (12.2 m)

2 44 ft. (13.5 m) 32 ft. (9.8 m)

3 32 ft. (9.8 m) 24 ft. (7.3 m)

4 28 ft. (9.5 m) 16 ft. (4.9 m)

Install male ﬁttings in correct direction:

CORRECT INCORRECT

See also CLEARANCE REQUIREMENTS on the next page.

Exhaust direction

Directional exhausting can be accomplished by installing a

quick-turn 90° dryer vent elbow directly to exhaust outlet of

dryer. Dryer vent elbows are available through your local parts

distributor or hardware store.

Exhaust system requirements, continued

In installations where the exhaust system is not described in

the charts, the following method must be used to determine

if the exhaust system is acceptable:

1. Connect an inclined or digital manometer between the

dryer and the point the exhaust connects to the dryer.

2. Set the dryer timer and temperature to air ﬂuff (cool

down) and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUST NOT be higher than

0.75 inches of water column. If the system back pressure

is less than 0.75 inches of water column, the system is

acceptable. If the manometer reading is higher than .075

inches of water column, the system is too restrictive and

the installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could affect

the performance of the dryer:

Only the rigid metal duct work should be used.•

Venting vertically through a roof may expose the exhaust•

system to down drafts causing an increase in vent

restriction.

Running the exhaust system through an uninsulated area•

may cause condensation and faster accumulation of lint.

Compression or crimping of the exhaust system will cause•

an increase in vent restriction.

The exhaust system should be inspected and cleaned a•

minimum of every 18 months with normal usage. The

more the dryer is used, the more often you should check

the exhaust system and vent hood for proper operation.

Manufactured or mobile home installation

Installation MUST conform to current Manufactured1.

Home Construction & Safety Standard, Title 24 CFR, Part

32-80 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD Part 280) or

Standard CAN/CSAZ240 MH.

Dryer MUST be exhausted outside (outdoors, not beneath2.

the mobile home) using metal ducting that will not support

combustion. Metal ducting must be 4 inches (10.16 cm) in

diameter with no obstructions. Rigid metal duct is preferred.

If dryer is exhausted through the ﬂoor and area beneath3.

the mobile home is enclosed, the exhaust system MUST

terminate outside the enclosure with the termination

securely fastened to the mobile home structure.

Refer to previous sections in this guide for other important4.

exhaust venting system requirements.

When installing a gas dryer into a mobile home, a5.

provision must be made for outside make up air. This

provision is to be not less than twice the area of the dryer

exhaust outlet.

Installer MUST anchor this (1) dryer or (2) dryer mounted6.

on pedestal to the ﬂoor with approved Mobile Home

Installation Kit - P/N 137067200.

Use of 90° quick-turn elbow required to meet mini-

mum installation depth of free-standing dryer:

Straight back venting allows for 0” (0 cm) installation.•

Venting right with 90° elbow allows for 0.75” (2 cm)•

installation.

Venting downward with 90° elbow allows for 0.75” (2 cm)•

installation.

Venting left with short, straight adapter and 90° elbow•

allows for 3.75” (9.5 cm) installation.

Venting upward with short, straight adapter and 90°•

elbow allows for 4” (10.5 cm) installation.

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under-

Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.54 cm)

Clearance requirements

60 sq. in.

(387.1cm²)

3”

(7.6cm)

60 sq. in.

(387.1cm²)

3”

(7.6cm)

0”

(0cm)

0”

(0cm)

1”

(2.54cm)

0”

(0cm)

INSTALLATION IN A RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom, recess or closet,

MUST be exhausted outdoors.

2. No other fuel burning appliance shall be installed in the

same closet as the gas dryer.

3. Your dryer needs the space around it for proper

ventilation.

DO NOT install your dryer in a closet with a solid door.

4. Closet door ventilation required: A minimum of 120

square inches (774.2 cm²) of opening, equally divided at

the top and bottom of the door, is required. Openings

should be located 3 inches (7.6 cm) from bottom and top

of door. Openings are required to be unobstructed when

a door is installed. A louvered door with equivalent air

openings for the full length of the door is acceptable.

closet door

or other than straight back venting, a quick-turn 90°

dryer vent elbow (vented right or down in free-standing

dryer or right on pedestal-mounted dryer) must be

installed to achieve 0” (0 cm) installation.

- EXPLOSION HAZARD - Do not install the

dryer where gasoline or other ﬂammables are kept or stored.

If the dryer is installed in a garage, it must be a minimum

of 18 inches (45.7 cm) above the ﬂoor. Failure to do so can

result in death, explosion, ﬁre or burns.

DO NOT INSTALL YOUR DRYER:

In an area exposed to dripping water or outside weather1.

conditions.

In an area where it will come in contact with curtains,2.

drapes, or anything that will obstruct the ﬂow of com-

bustion and ventilation air.

On carpet. Floor MUST be solid with a maximum slope of3.

1 inch (2.54 cm).

To achieve an installation with 0” (0 cm) clearance

for the back of the dryer (for other than straight back vent-

ing), a quick-turn 90° dryer vent elbow must be installed as

described previously in this manual.

36.0”

(91.5cm)

16.9”

(43cm)

19.0”

(48cm)

51.25”

(130cm)

1.6”

(4cm)

3.75”

(9.5cm) 13.50”

(34.5cm)

to center of rear vent

3.7”

(9.5cm)

gas supply

pipe on rear

of gas unit

48.25” (122.5cm)*

to clear open door 30.5” (77.5cm)*

to front of closed door

27.0”

(68.5cm)

centerline

height for

rear vent

electrical

supply on

rear of unit

freestand dryer

on floor

floor line

dryer mounted on

optional pedestal

* To obtain these minimal depth dimensions, dryer must be vented straight back.

Using a quick-turn 90° elbow (right or down on freestanding dryer) adds approximately

0.75 in. (2.0 cm) to installation depth. Upward venting of exhaust on pedestal-mounted

or freestanding dryer adds approximately 4 in. (10.2 cm) to installation depth. Leftward

venting on pedestal-mounted or freestanding dryer adds approximately 3.75 in. (9.5 cm)

to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds

approximately 2.25 in. (5.7 cm) to installation depth.

* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to

installation depth. Upward venting of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on

stacked dryer adds approximately 2.25 in. (6.5 cm) to installation depth. Leftward venting of exhaust on stacked dryer adds approximately 3.75 in. (9.5 cm) to

installation depth.

71.5”

(182cm)

39”

(99cm)

37”

(94cm)

gas supply

pipe on rear

of gas unit

48.25” (122.5cm)*

to clear open door 30.5” (77.5cm)*

to front of closed door

centerline

height for

rear vent

electrical

supply on

rear of unit

27.0”

(68.5cm)

Installed dryer dimensions

The following are speciﬁc requirements for proper and safe

electrical installation of your dryer. Failure to follow these

instructions can create electrical shock and/or a ﬁre hazard.

Grounding requirements - Electric dryer (USA)

Electrical installation

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance for

electrical current.

2. After you purchase and install a 3 wire or 4 wire power

supply cord having an equipment-grounding conductor

and a grounding plug that matches you wiring system,

- ELECTRICAL SHOCK HAZARD -

This appliance MUST be properly grounded. Electrical•

shock can result if the dryer is not properly grounded.

Follow the instructions in this manual for proper ground-

ing.

Do not use an extension cord with this dryer. Some ex-•

tension cords are not designed to withstand the amounts

of electrical current this dryer utilizes and can melt, creat-

ing electrical shock and/or ﬁre hazard. Locate the dryer

within reach of the receptacle for the length power cord

to be purchased, allowing some slack in the cord. Refer

to the pre-installation requirements in this manual for the

proper power cord to be purchased.

- ELECTRICAL SHOCK HAZARD -

A U.L.-approved strain relief must be installed onto pow-•

er cord. If the strain relief is not attached, the cord can be

pulled out of the dryer and can be cut by any movement

of the cord, resulting in electrical shock.

Do not use an aluminum wired receptacle with a copper•

wired power cord and plug (or vice versa). A chemical

reaction occurs between copper and aluminum and can

cause electrical shorts. The proper wiring and receptacle

is a copper wired power cord with a copper wired recep-

tacle.

Dryers operating on 208 volt power supply will have

longer drying times than dryers operating on 240 volt power

supply.

- ELECTRICAL SHOCK HAZARD - Improper

connection of the equipment grounding conductor can result

in a risk of electrical shock. Check with a licensed electrician

if you are in doubt as to whether the appliance is properly

grounded.

the plug MUST be plugged into an appropriate, copper

wired receptacle that is properly installed and grounded

in accordance with all local codes and ordinances. If in

doubt, call a licensed electrician.

DO NOT modify the plug you’ve installed on this appliance.

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded metal,

permanent wiring system; or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance.

Grounding requirements - Electric dryer (Canada)

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electrical shock by a path of least resistance for

electrical current.

- ELECTRICAL SHOCK HAZARD - Improper

connection of the equipment grounding conductor can result

in a risk of electrical shock. Check with a licensed electrician

if you are in doubt as to whether the appliance is properly

grounded.

2. Since your dryer is equipped with a power supply

cord having an equipment-grounding conductor and

a grounding plug, the plug must be plugged into an

appropriate outlet that is properly installed and grounded

in accordance with all local codes and ordinances. If in

doubt, call a licensed electrician.

DO NOT modify the plug provided with the appliance.

The dryer is equipped with a three-prong (grounding) plug1.

for your protection against shock hazard and should be

plugged directly into a properly grounded three-prong

receptacle.

The plug must be plugged into an appropriate outlet that2.

is properly installed and grounded in accordance with all

local codes and ordinances. If in doubt, call a licensed

electrician.

DO NOT cut or remove ground prong from the plug.

Grounding type

ll receptacl

ll receptacle

wer cord with

3-prong

ounded plug

Do not,

under

y cir

cumstances,

cut,

remo

ve,

or b

ypass th

ypass the

ounding pr

ong.

Grounding requirements - Gas dryer (USA and Canada)

Gas connection

Remove the shipping cap from gas pipe at the rear of the1.

dryer.

Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved2.

pipe from gas supply line to the 3/8 inch (0.96 cm) pipe

located on the back of the dryer. Use a 1/2 inch to 3/8

inch (1.27 cm to 0.96 cm) reducer for the connection.

Apply an approved thread sealer that is resistant to the

corrosive action of liqueﬁed gases on all pipe connections.

Open the shutoff valve in the gas supply line to allow gas3.

to ﬂow through the pipe. Wait a few minutes for gas to

move through the gas line.

All connections must be wrench-tightened

Flare

Union

Flare

Union

GAS FLOW

Manual

Shuto

Valve

Closed

Open Flexible

Connector

Inlet Pipe on

Back of Dryer

elppiN

Shuto Valve -

Open position

to dryer

from gas supply

Check for gas system leaks with a manometer. If a4.

manometer is not available, test all connections by

brushing on a soapy water solution.

- EXPLOSION HAZARD - NEVER test for gas

leaks with an open ﬂame.

The supply line must be equipped with an ap-

proved manual shutoff valve. This valve should be located in

the same room as the dryer and should be in a location that

allows ease of opening and closing. Do not block access to

the gas shutoff valve.

DO NOT connect the dryer to L.P. gas service

without converting the gas valve. An L.P. conversion kit must

be installed by a qualiﬁed gas technician.

This manual suits for next models

Table of contents

Languages:

Other Frigidaire Dryer manuals

Frigidaire

Frigidaire Affinity FAQG7073K W User manual

Frigidaire

Frigidaire AEQ6400HS0 User manual

Frigidaire

Frigidaire GLER331AS2 Quick start guide

Frigidaire

Frigidaire Affinity FASE7073LA Installation instructions

Frigidaire

Frigidaire GLET1041AS0 User manual

Frigidaire

Frigidaire FAQE7011KW - 7 cu. Ft. Cycle Electric Dryer... Owner's manual

Frigidaire

Frigidaire FGFB9100E User manual

Frigidaire

Frigidaire FASE7073NA User manual

Frigidaire

Frigidaire FAQE7021LB Installation instructions

Frigidaire

Frigidaire FGFB9100ES0 User manual

Frigidaire

Frigidaire FAQE7017K User manual

Frigidaire

Frigidaire AGQ6000CE User manual

Frigidaire

Frigidaire LCGQ2152FE0 User manual

Frigidaire

Frigidaire FRG5714KW - Gas Dryer w/ 4 Temps User manual

Frigidaire

Frigidaire CFQE5000QW User manual

Frigidaire

Frigidaire 131679000B User manual

Frigidaire

Frigidaire FEQ5000HS0 User manual

Frigidaire

Frigidaire Affinity FAQE7011LB User manual

Frigidaire

Frigidaire Affinity FAQE7001LW Installation instructions

Frigidaire

Frigidaire AGQ7000E User manual

Frigidaire

Frigidaire GLGQ332MAS0 Quick start guide

Frigidaire

Frigidaire FARE4044MW User manual

Frigidaire

Frigidaire 137181700A Owner's manual

Frigidaire

Frigidaire GLGR1042FC1 User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions