Frigidaire L0806995 User manual

installation instructions

For Heavy Duty (FAS Models) and

Median (FAM Models) Air Conditioners

Please read ALL instructions before installing. Two people are

recommended to install this product. If a new electrical outlet

is required, have the outlet installed by aqualified electrician

before installing unit, See#5 in Preliminary Instructions

following.

Prelimi nary instru ctions

Do the following before starting to install unit. See illustrations

below.

Check dimenstions of your unit to determine model type:

Heavy duty (FAS) Median (FAM)

Unit Height: 18,5/8" 17.5/8"

Unit Width: 261/2" 231/2"

Min. Window Opening: 19" 181/2"

Min. Window Width: 31" 26 Vj'

Max. Window Width: 43" 40 V2"

1. Check window opening size- the mounting parts furnished

with this air conditioner are made to install in a wooden

sill double-hung window.The standard parts are for

window dimensions listed above.Open sash to a minimum

of 1g"(483mm). (FIG. 1)

2. Check condition of window- all wood parts of window

must be in good shape and able to firmly hold the needed

screws.if not, make repairs before installing unit.

FIG. 1

_1SASH

19" MIN

1/2" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

FOAM GASKET

WASHERHEAD

LOCKENG SCREW_._._ X

ASSEMBLY

(LEFT)

SIDE RETAENER J

BRACKET

3. Check your storm windows= if you storm window

frame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG.2, or by removing

storm window while room air conditioner is being installed.

(continued)

FIG. 2

// SASH

19"MIN

1112

STORM WINDOW FRAME OR WITH TWO NAILS OR

OTHER OBSTRUCTION SCREWS.

P/N 6612990 1162

4. CHECK FOR ANYTHING THAT COULD BLOCK

AIRFLOW -check area outside of window for things

such as shrubs, trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not stop proper air flow.

5. Check the available electrical service - power supply must

be the same as that shown on the unit serial nameplate.

(See Owner's Guide for serial plate Iocation.)Power cord

is 48"long. Be sure you have an outlet near.

Tools Required

a large flat blade screwdriver

tape measure

adjustable wrench or pliers

pencil

_/ Level

_/ Socket wrenches

_/ Phillips screwdriver

All models have a 3-prong service plug to provide proper

service and safe positive grouding. Do not change plug in

any way. Do not use an adapter plug. If your present wall

outlet does not match your plug, call a qualified electrician

to make the needed change.

::_i Avoid fire hazard or electric

shock, Do not use an extensioncord or an

adaptor plug. Do not remove any prong

from the power cord.

Grounding type wall

receptacle

Power supply core

NIth3-prong groundi

plug and current

detection device

6. Carefully unpack air conditioner -remove a!l packing

material. Protect floor or carpet from damage. Two

people should be used to move and install unit.

Hardware (in plastic bag)

Washer Head

Locking Screw

For window panels

3/4" Long Hex-

Head Screw

[_ Safety Lock

_ 1/2" Long Screw

and Iocknut

3/4" Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

Long hex-head

locking screw for

top angle, side

retainer 5116"

Long

LJty.

4 ea.

2 ea.

"ndow Mounting

g Remove Chassis

1. Pull down front panel and remove filter. (See FIG. 1).

2. Lil_front upwards and place to one side.

DInstall Top Angle

and Side Bracket

1. Attach foam gasket to top angle above holes as

shown in FIG. 6.

3. Locate the four front screws and remove. These screws

will be needed to re-install the front later. (See FIG.2)

4. Pry away front from cabinet sides as per photo (see FIG .3)

5. Gently lift front off unit and place to one side (See FIG.4).

2. Install top

angle and

side retainers

to cabinet as

shown in FIG. 6.

FIG. 6

6. Removeshi ppingcrewsfrom top dunit and_tso on theside

by the base if installed.

7. Hold the cabinet while pulling on the base handle, and

carefully remove the unit.

8. Add two foam inserts to holes in top of cabinet where

shipping screws were removed from.

Assemble Window

aFiller Panels

1. Place cabinet on floor, a bench, or a table.

2. Slide 'T' section of window filler panel into side retainer

on the side of the cabinet (see Figures 7-8). Do both

sides.

FIG. 7

PLASTIC WINDOW FILLER

FRAME PANEL

9. Your unit may come with internal packaging.THIS

PACKAGING MUST BE REMOVED PRIOR TO

INSTALLING THE AIR CONDITIONER BACK

INTO THE CABINET. (See FIG. 5). FIG. 8

TOP

VIEW

SIDE

RETAINER

PLASTIC

FRAME

LOCKING

'T'SECTION WINDOW SCREW

HOLE

FILLER

PANEL

3. Insert top and bottom legs of window filler panel

frame into channel in the to angle and bottom rail.

Do both sides.

4. Insert washer head locking screws (2) into holes in

top leg dfiller panel frame (see Step 6). Do not

totally tighten. Allow leg to slide freely. Screws will

be tightened after Section 6.

Place Cabinet in

Window

1. Open window and mark

center of window stool.

M Install Support

Bracket

1. Hold each support bracket flush against outside of sill,

and tight to bottom of cabinet as shown below. Mark

brackets at top level of sill, and remove.

MARK

.Place cabinet in window with bottom stool angle firmly

scated over window stool as shown. Bring window

down temporarily behind top angle to hold cabinet in

place.

3. Shift cabinet left or right as needed to line up center

of cabinet on center line marked on stool.

4. Fasten cabinet to window stool with 2 screws into

holes.(You may wish to pre-drill pilot holes.)

5. Add bottom rail seal over screws to window stool.

Bottom

Rail Seal

-- o N /o --

_' tong HEX+

HEAD SCREW

L=ET _.1/2" LONG SCREWS

'- r'_:_/i_N D LOC _N UTS

LODKNUT !/

BRACKET---_ _)'_ I11//

FLAT HEAD BOLT _ <:_ _L/

2 EACH REQ'D FOR EACH

SUPPORT BRACKET

2. Asscmble sil! angle bracket to support brackets at the

marked position, as shown. Hand tighten, but allow

for any changes later.

3. Install support brackets (with sill angle brackets

attached) to correct hole in bottom of cabinet as shown.

4. Tighten all 6 bolts securely.

Z_ I/2" long screws

and Iocknuts

Extend Window Filler

...........Panels

1. Carefully raise window to expose filler panel locking

screws. Loosen screws so filler panels slide easily.

install Chassis into

Cabinet and install

Front to Unit

1, Lift air conditioner and carefully slide into cabinet

leaving 6" protruding,

2. _DO not push on controls OR finned coils.

3, Be sure chassis is firmly seated towards rear of cabinet.

4. Installation of front is the reverse of removal outlined

in Section 1.

2. Extend panels to fill window opening completely.

Tighten locking screws on top,

3. Close window behind top angle.

Install Window Lock

and Sash Seal

1, Trim sash seal to fit window width. Insert into space

between upper and lower sashes.

OW SASH SEAL

2. Attach right angle safety lock as shown,

SAFJTY LOCK

3/4" }orlg hex-

Thru-The-Wall installation

NOTE: Consult local building codes prior to installation,

or a qualified carpenter.

Select Wall Location

This air conditioner has a slide-out chassis, so that it can

be installed through an outside wall as specified below:

Heavy Duty(FAS) Median (FAM)

Max wall thickness 10" 8"

IMPORTANT: Side louvers must never be blocked.

NOTE: All parts needed for Thru-The-Wall Installation

are provided,except a wood frame, shims, and 10 wood

screws (#10-1" long minimum). Select a wall surface that:

1, does not support major structural loads such as the

frame construction at ends of windows, and under

truss-bearing points, etc.

2. does not have plumbing or wiring inside.

3, is near existing electrical outlets, or where another

outlet can be installed,

4. faces, and is not blocked to the area to be cooled.

5. allows unblocked airflow from rear sides and end

(outside) of installed air conditioner.

Prepare Wall

1. Prepare wall in frame construction (including brick

and stucco veneer). Working from inside the room,

find wall stud nearest the center of area where air

conditioner will be installed (by sounding wall, or by

magnetically finding nails).

2. Cut or knock out a hole on each side of center stud.

3. Measure between inside edges of every other stud as

shown in FIG. 1.

FIG. 1

3-3/8" MIN

(8.8 cm)

Carefully measure and cut an opening with the following

dimensions depending on your model. See FIGS, land 2.

WIDTH "X" = inside model width plus twice the thickness

of framing material used.

HEIGHT "Y" = inside model height plus twice the thickness

of framing material used.

Heavy Duty (FAS)

inside Frame Height: 18-_8"(47.9cm)

Inside Frame Width: 2@4" (67.9cm)

Median (FAM)

18" (45.7cm)

231J8"(60.6cm)

FIG. 2

8-1/2"

4. Build a wooden frame with the INSIDE dimensions of

your model listed above. Measure twice remember...)

Frame depth should be the same as wall thickness. Fill

in the space from the opening to the studs with wood

spacers, as shown.

5, Nail framd to spacers to spacers with front flush with

dry wall.

'-NAIL SPACERS TO STUDS

NOTE: If wall thickness is 8-1/2" or more, add aluminum

flashing over bottom of frame opening to assure no water

can enter area between inner and outer wall.

1"LONG

SCREW

FIG.2

ALUMINUM FLASHING

OVER BOTTOM OF FRAME

IPrepare and Install

Cabinet

Refer to Step 4 dWindow Mounting for assembly of

support brackets.A wooden strip nailed to the outside

wall should be used in conjunction with sill support

angle brackets.

1. Slide chassis from cabinet. Refer back to Step 1 of

Window Mounting.

2. Place cabinet into opening with bottom rail resting

firmly on bottom board dwooden frame.

3. Position cabinet to achieve proper slope for water removal.

(See FIG.1 below.)

FIG. 1

5/16"

3/8"

3/4"PLUS

THICKNESS

SEE PARA 5

brakcet

5. Screw or nail cabinet wooden frame using shims if

frame is oversized, to eliminate distortion. Remember

to maintain proper slope as described in Step 3.

LEVEL '_

4. Secure bottom rail to wood frame with two large wood

screws 1"(2.5 cm)long using the two holes in the bottom

of the channel resting on frame.(See FIG.2 following) 6. Install chassis into cabinet by following all steps in

Step 8 of Window Mounting.(continued)

OPTIONAL: Caulking and installation of trim on interior

wall may be done. You can buy wood from your local lumber

or hardware supply. On the outside, caulk openings around top

and sides of cabinet, and all sides of wood sleeve to the opening.

NOTE: See Step 7, Item 3 of Window Mounting Instructions

for bottom rail seal location.

Masonry Construction

1. Cut or build a wall opening in the masonry wall similar

to the frame construction(refer to Step 2 dThru-the-Wall

Installation for a wall thickness greater than 8-1/2").

2. Secure cabinet in place using masonry nails, or the right

masonry anchor screws.(Another way to do this is to build

an in -between frame of2x4 's as shown in the Step 2 Prepare

Wall illustrations-but make it double framed on either side,

and install between masonry wall opening and cabinet.

Frame must be securely anchored to masonry wal! opening)

This way gives very good louver clearance on either side of cabinet.

3. Install a linted to support masonry wal! above cabinet.

Existing holes in cabinet can be used and/or additions holes

can be drilled to fasten cabinet at various positions.Be sure

that side louver clearance is in accordance with Step 1above.

4. Install exterior cabient suppport brackets as shown in

Step 2 dThru-the-Wall Installation.Caulk or flash if

neede, to provide a wether-tight seal around top and sides

of cabinet.

5. To complete installation, apply wood trim molding

around room side projection dcabinet.

This manual suits for next models

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FAH126N2 User manual

Frigidaire

Frigidaire FRS123LS1 Owner's manual

Frigidaire

Frigidaire FAH125P2T1 Service manual

Frigidaire

Frigidaire FGRQ0633U1 Owner's manual

Frigidaire

Frigidaire FFRE0533Q1 User manual

Frigidaire

Frigidaire FAC089L7A1 User manual

Frigidaire

Frigidaire FAC054K7A6 User manual

Frigidaire

Frigidaire FAS157P1A2 Service manual

Frigidaire

Frigidaire FATC18FNVWHE User manual

Frigidaire

Frigidaire FFRL0633Q1 User manual

Frigidaire

Frigidaire FAH096J2T1 User manual

Frigidaire

Frigidaire CRA050XT719 Owner's manual

Frigidaire

Frigidaire FFRA0811R1 Owner's manual

Frigidaire

Frigidaire FRS093LS1 Installation instructions

Frigidaire

Frigidaire FAC084K7A2 User manual

Frigidaire

Frigidaire FFRA 22R1 Series Owner's manual

Frigidaire

Frigidaire FRA156MT1 User manual

Frigidaire

Frigidaire Room Air Conditioner User manual

Frigidaire

Frigidaire FAC085K7A4 User manual

Frigidaire

Frigidaire FAC124N1A User manual

Frigidaire

Frigidaire FRS093LS1 User manual

Frigidaire

Frigidaire LRA08PZU1 User manual

Frigidaire

Frigidaire FHSC102WB1 User manual

Frigidaire

Frigidaire FAK085T7V1 Owner's manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions