Frigidaire FRA103BT113 User manual

FRIGIDAIRE

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii__

iii¸/im

Product

ackaging .;,

aormat sounds :L

www,frigJ

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as

instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that

may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

The power supply cord with

this air conditioner contains a current

detection device designed to reduce the risk

of fire.

UPlease refer to the section 'Operation of

Current Device' for details.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance. Read product labels for flammability and other warnings.

In the event that the power supply cord is Prevent Accidents

damaged, it cannot be repaired, tt must be

replaced with a cord from the product To reduce the risk of fire, electrical shock, or injury to persons when using your air conditionel

manufacturer, followbasicprecautions,includingthefollowing:

° Be sure the electrical service is adequate for the model you have chosen. This information

Avoid fire hazard or electric shock. Do not

use an extension cord or an adaptor plug. Do

not remove any prong from the power cord.

can be found on the serial plate, which is located on the side of the cabinet and behind the

grille.

• If the air conditioner is to be installed in a window, you will probably want to clean both

iiii ii sides of the glass first. If the window is a triple-track type with a screen panel included,

remove the screen completely before installation.

• Be sure the air conditioner has been securely and correctly installed according to the

separate installation instructions provided with this manual. Save this manual and the

installation instructions for possible future use in removing or reinstalling this unit.

•When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front

and rear coils.

DANGER.IAvoid Serious Injury or Death

This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.

Do not insert or place fingers or objects into the air discharge area in the front of the unit.

Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.

Do not cut or damage the power cord.

If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.

In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized

Electrolux servicer.

• Do not operate the air conditioner with wet hands.

• Do not pull on the power cord.

• Do not drink any water that is drained from the air conditioner.

CAUTION. IAvoid Injury or damage to the unit or other property

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make

units run excessively.

Do not climb on or place objects on outdoor part of the unit.

Do not hang objects off the unit.

Do not place containers with liquids on the unit.

Turn off the air conditioner at the power source when it will not be used for an extended period of time.

Periodically check the condition of the unit's installation accessories for any damage.

Do not apply heavy pressure to the radiator fins of the unit.

Operate the unit with air filter in place.

Do not block or cover the intake grille, discharge area and outlet ports.

Ensure that any electrical/electronic equipment is one yard away from the unit.

Do not use or store flammable gases near the unit.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Unit must be upright for one hour prior to operating.

Operation of Current

Device

Plug in & _,

press RESET

The power supply cord contains a current device that senses damage to the power cord. To test

your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will

notice a click as the RESET button pops out.

3. Press the RESET button, Again you will notice a click as the button engages,

4. The power supply cord is now supplying electricity to the unit,

Do not use this device to turn the unit on or off.

• Always make sure the RESET button is pushed in for correct operation.

, The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,

or it cannot be reset. A new one can be obtained from the product manufacturer.

•If power supply cord is damaged, it CANNOT be repaired, It MUST be replaced by one obtained

from the product manufacturer.

Product Registration Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the

serial plate is located on the outside of the cabinet.

Model No.

Serial No.

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,

signed and returned to the Frigidaire Company.

Packaging Remove all packaging from inside the carton, along with any

inserts placed into the side louvers.

PACKAGING INSERTS

: i

! r

o/o o- o jj

Normal Sounds

High pitched Chatter

Today's high efficiency compressors

may have a high pitched chatter

during the cooling cycle.

Sound of Rushing Air

At the front of the unit, you may

hear the sound of rushing air

being moved by the fan.

Vibration

Unit may vibrate and make noise

because of poor wall or window

construction or incorrect installation.

Pinging or Swishing

Droplets of water hitting condenser

during normal operation may cause

"pinging or swishing" sounds.

Gurgle/Hiss

"Gurgling or hissing" noise may be

heard due to refrigerant passing

through evaporator during normal

operation.

Air Conditioner Features ELECTRONICCONTROL

f TEMP/TIMER

TEMP/TIMER ..i

CLEAN AIR

FEATURE SENSING INDICATOR DISPLAYS

(some models) -- (some models) TEMPERATURE/TIME _ CHECK FILTER

RESETBUTTON

dean cod remote hi filter

econ sensing med

air Sanonly lo reset ]

er MODE VON-OFF AFAN SPEED s|qep /

SETS NODE ADJUSTS SETS FAN

TEMPERATURE SPEED

OR TIME

0 0 0

coot energy fan

saver only

sleep auto timer

fan

fFRIGIDAIRE _

STANDARD REMOTE

F G o q

fTEHPITIHER

,_. TENP/TIMER

oo0

cool energy fan

saver on{y

[] © []

steep auto timer

fan

start [_ stop

remote sensing

fFRIGID_IRE "_

w/DISPLAY &

REMOTE SENSING

BUTTON

REMOTE TEMP

Before you begin, thoroughly familiarize yourself with the control panel and remote

as shown below and all its functions, then follow the symbol for the functions you

desire. The unit can be controlled by the touch pad alone or with the remote.

Battery Size: AAA

Warning: Do not mix old and new batteries. Do not mix alkaline,

standard (carbon-zinc), or rechargeabte (nickel-cadmium) batteries.

Operating Instructions

The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON: YOU WILL SEE:

letup/timer )

Iauto I

cool remote I _ hi

econ sensing I _ reed I

fan only _to )

MODE V 0N-0FF A FAN SPEED

oo,..,:i

RESS ON/OFF BUTTON

Lromp/timer )

I F auto I

[] coot remote _ I hi []

econ sensing _ _ med

fan only _lo J

MODE V 0N-0FF AFAN SPEED

Operating Instructions

(continued)

TO CHANGE TEMPERATURE SETTING:

remote

sensing

tamp/timer

auto

hi [] fi|termed

Zo reset

V ON=OFF A FAN SPEED

DO THIS:

PRESS A TO RAISE

PRESSV TO LOWER

sleep

YOU WILL SEE:

remote

sensing

tamp/timer F

auto

hi , filter

mad

Zo reset

V ON=OFF A FAN SPEED sleep

Note: Tap or hold either up ( A ) or down ( V ) button until

the desired temperature is seen on the display. This tempe-

rature will be automatically maintained anywhere between

60 °F (16 °C) and 90 °F (32 °C). If you want the display to

read the actual room temperature. See "To Operate on Fan

Only" section on Page 7.

TO AD3UST FAN SPEEDS:

emote

sensing

temp/timer F

vON-OFF A

auto ,,/1

hi .filter

med

Zo reset

FAN SPEED sleep

\DO THIS:

YOU WILL SEE:

remote

sensing

temp/timer auto !

medhi /filter

lo , reset

VON-OFF A FAN SPEED sleep

PRESSTO SELECT

TO USE AUTO FAN FEATURE:

remote

sensing

tamp/rimer

auto J

reed

lo []

lifter

reset

V ON-OFF AFAN SPEED

DO THIS;

sleep

PRESSFAN BUTTON,

CHOOSEAUTO

YOU WILL SEE:

remote

sensing

temp/timer auto [] I

medhi /fitter

Zo reset

V0N=0FF A FAN SPEED sleep

Note: Fan starts at High Speed and adjusts to a slower

speeds the room temperature dictates. For example, if the

room doesn't get too warm, it will stay at the slowest speed.

If the room temperature rises quickly, such as a door being

opened, it will automatically go to the highest speed. The fan

speeds will re-adjust back to the slowest speed as the room

returns to the original set temperature. Press either the fan

slower or fan faster button to adjust the fan speed manually.

Operating Instructions

(continued)

TO OPERATE ON FAN ONLY:

ctearl _ m cool remote

\econ sensing

air #n only

temp/timer m

timer MODE V ON-OFF A

DO THIS:

PRESS

MODE BUTTON

CHOOSE

FAN ONLY

YOU WILL SEE:

c[eall _cool remote

\econ sensing

air [] #n only

temp/timer

timer MODE V 0N-0FF A

Note: Use this function only when cooling is not desired,

such as for room air circulation or to exhaust stale air on

some models. (Remember to open the vent during this

function, but keep it closed during cooling for maximum

cooling efficiency.) You can choose any fan speed you

prefer. (Except "Auto Fan").

During this function, the display will show the actual room

temperature, not the set temperature as in the cooling

mode.

TO USE THE ENERGY SAVER (ECON) FEATURE:

dean \ cool remote

\econ sensing

air []fanonly

temp/timer m

timer MODE V ON-OFF A

DO THIS;

PRESS

MODE BUTTON

CHOOSE ECON

YOU WILL SEE:

dean \ cool remote

air _ ,econ sensing

Ion only

temp/timer m

timer MODE V ON-OFF A

Note: In this mode, the fan will continue to run for 1 minu-

te after the compressor shuts off. The fan then cycles on

for 20 seconds at 10 minute intervals until the room tempe-

rature is above the set temperature, at which time the com-

pressor turns back on.

SLEEP FEATURE: YOU WILL SEE:

romp/timer l

remote hi []

sensing reed

V ON-OFF A FAN SPEED

fitter

reset

steep

DO THIS:

PRESS

SLEEP BUTTON

remote

sensing

temp/timer Fmauto J

hi m

reed

V ON-OFF A FAN SPEED

fitter

reset

steep

Note: In this mode the selected temperature will increase

by 2 °F 30 minutes after the mode is selected. The tempe-

rature will then increase by another 2 °F after an additional

30 minutes. This new temperature will be maintained for 7

hours before it returns to the originally selected tempera-

ture. This ends the "Sleep" mode and the unit will continue

to operate as originally programmed. The "Sleep" mode

program can be cancelled at any time during operation by

again pressing the "Sleep" button.

Operating Instructions

(continued)

TIMER: DELAY STOP JSTART FEATURE

clean _=cool remote

kecon sensing

air Ion only

temp/dmer

timer NODE V 0N-0FF

YOU WILL SEE HOW MUCH TIME IS CHOSEN:

clean i [] cool

econ

air fan only

[]

timer NODE

remote

sensing

temp/timer

v ON-OFF A

\\FI RST

DO THIS:

PRESS

TIMER BUTTON

THEN

DO THIS:

PRESS

UP/DOWN BUTTONS

Note: For Delay Stop, the unit must be in the On position.

Note: For Delay Start, the unit must be in the Off position.

First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( A ) or the DOWN arrow ( V ) to change delay

timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time

remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,

Energy Saver, or Fan Only was the last mode selected). The temperature maintained will be the same as previously set. To change

the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5

seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the

unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either

starts or stops. Once that happens the above steps have to be repeated again.

CHECK FILTER FEATUREr YOU WILL SEE:

temp/timer l

mauto.

remote hi filter

sensing med

lo reset

V 0N-0FF AFAN SPEED sleep

Note: This feature is a reminder to clean the Air Filter (See

Care and Cleaning) for more efficient operation. The LED

(light) will illuminate after 250 hours of operation. To reset

after cleaning the filter, press the "Filter Reset" button and

the light will go off.

CLEAN AIR FEATURE(on some models):

temp/timer )

Fauto [] I

remote _T| _ hi I filter

sensing _ I_ reed Ireset

lo ]

V 0N-0FF A FAN SPEE_

DoTHIS:/I

PRESS FILTER

RESET BUTTON

temp/timer F

dea. \ ,cool remote m

• I econ sensing role i_W m

alr L fan only

MODE V 0N=0FF A

DO THIS:

PRESS

CLEAN AIR

BUTTON

8@2009 Electrolux Home Products, Inc.

clean [] coo! remote

air ;aCOnnonlysensing

temp/timer

timer MODE V ON=OFF A

Note: When this feature is "ON", the electronic air purifier is

energized to remove pollen and impurities from the air. To

cancel this feature, press the Clean Air button (the LIGHT

will turn off).

Note: This feature can be activated on the unit touch pad

ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!!!ii;i!ii

Operating Instructions

(continued)

REMOTE SENSING FEATURE

(on some models).

\ s

| I

TEMp/TIMER

_ Q o

remote 5e#sing

DO THIS:

PRESS REMOTE

SENSING

START BUTTON

dean

air

LIGHT pulsing ( On & Off intermittently ).

cool remote F

econ sensing

#n only |

timer MODE V ON-OFF A

NOTE: Unit display shows the set temperature

__J

NOTE: Remote display

is actual temperature

at remote control only

Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode.

To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use

the" A V "buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit

itself ). The LIGHT on the unit control wilt pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it

sends a signal. It will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. If the unit

does not receive the remote sensing signal during any 3 minute interval, the unit wilt beep to indicate the remote sensing mode has

ended. The display on the remote control indicates the temperature at the remote ONLY.

NOTE: The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON/OFF button on the

unit.

FAULT CODES:

remote

sensing

ternp/timer

auto [] i

medhi fitter

lo reset

V 0N=0FF AFAN SPEED sleep

If the display reads "AS", a sensor has failed. Contact your

Authorized Frigidaire Service Center.

TO CHANGE TEMPERATURE DISPLAY:

temp/timer l

m°ut°

remote hi .filter

sensing reed

lo reset

VON-OFF A FAN SPEED

/DO THIS:

PRESS AND HOLD THE

UP/DOWN BUTTONS

TOGETHER FOR 3 SECONDS

sleep

YOU WILL SEE:

remote

sensing

temp/timer mauto ;

hi , fitter

reed

lo reset

VON-OFF A FAN SPEED sleep

Note: The control is capable of displaying temperature in

degrees Fahrenheit or degrees Celsius.

Operating Instructions

(continued)

TO TURN UNIT OFF:

remote

sensing

temp/timer

auto J

hi. fitter

med

to reset

V ON-OFF AFAN SPEED s[eep

PRESS

ON/OFF BUTTON

YOU WILL SEE;

temp/timer auto l

remote _ _ hi fitter

sensing med

to reset

V ON-OFF A FAN SPEED s[eep

ADDITIONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

•The "Cool" circuit has an automatic 3 minute time delayed start if the unit isturned off and on quickly.

This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue

to run during this time.

, There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having

to roll through to select another mode.

• The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.

• After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.

Fresh Air Vent Control

The Fresh Air Vent allows the air conditioner to:

1. RecJrculate inside air - Vent Closed (see Fig. 1)

2. Exchange air from the room - Vent Open (see Fig. 2)

Figure i(VENT CLOSED)

Figure 2(VENT OPEN)

AUGER WHEELS

(8-WAY)

Air Directional Louvers

Air directional louvers control air flow direction. Your air conditioner has the louver

type described below.

Auger Type

The louvers will allow you to direct the air flow Up or Down and Left or Right

throughout the room as needed. Rotate the Auger Wheels until the desired

Left/Right direction is obtained. Pivot horizontal louvers until the desired

Up/Down direction is obtained.

This manual suits for next models

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FAS185J2A1 User manual

Frigidaire

Frigidaire FAS183K2A5 User manual

Frigidaire

Frigidaire CRA050XT73 User manual

Frigidaire

Frigidaire FAS254J2A2 User manual

Frigidaire

Frigidaire GALLERY GHWQ125WD1 Owner's manual

Frigidaire

Frigidaire FRA053XT715 Owner's manual

Frigidaire

Frigidaire FRA053XT738 Owner's manual

Frigidaire

Frigidaire FRA102BT110 Owner's manual

Frigidaire

Frigidaire FAK104P1V User manual

Frigidaire

Frigidaire FRA053XT7 Installation instructions

Frigidaire

Frigidaire FAC084J7A2 User manual

Frigidaire

Frigidaire FRA054XT7 User manual

Frigidaire

Frigidaire FAA087P7 User manual

Frigidaire

Frigidaire FRA182MT20 Owner's manual

Frigidaire

Frigidaire FAH14EQ2T4 User manual

Frigidaire

Frigidaire FAC104M1A1 User manual

Frigidaire

Frigidaire FHWW183WC2 Owner's manual

Frigidaire

Frigidaire FAD052M7A1 User manual

Frigidaire

Frigidaire FAC083M7A1 User manual

Frigidaire

Frigidaire CRA103BT13 User manual

Frigidaire

Frigidaire THRU-THE-WALL ELECTRONIC CONTROL AIR... User manual

Frigidaire

Frigidaire FRA12EHT2 Installation instructions

Frigidaire

Frigidaire FAS155K1A1 User manual

Frigidaire

Frigidaire FAC105L1A1 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions