Frigidaire FAH12EN2T User manual

Do This First

(for existing sleeve)

Note that the air conditioner dimensions are: 24"wide,

⁄

"high, and 18

⁄

"deep (without front). Install Air

Conditioner according to these installation instructions

to achieve the best performance. Save these installation

instructions for future reference.

Items in Kit

You may not need all parts in the kit. Discard unused

parts. Qty.

Tapered Spacer Blocks 17"Long 2

Centering/Support Blocks 4

⁄

"x 3

⁄

"x 1

⁄

Plastic Divider 1/8” x 4

⁄

"x 14

⁄

Stuffer Seal 1"x 1

⁄

"x 84"1

Seal 1

⁄

"x 1

⁄

"x 26

⁄

Seal 1

⁄

"x 1

⁄

"x 14"2

Seal 1

⁄

"x 3/8"x 26

⁄

Seal 1

⁄

"x 3/8"x 14"2

Seal 1” x 3/4"x 14"1

Trim Frame (side legs) 2

Trim Frame (top & bottom legs) 2

Ground Wire (green) 1

Nut for grounding screw 1

Grounding Screw 1

Grille (plastic) 1

Nuts (plastic) 4

Screw w/washer 4

How to Install

1. Identify the wall-sleeve brand for your installation,

from the chart below.

Brand Wall Sleeve Dimensions

(inches)

Width Height Depth

White-Westinghouse

Frigidaire 25

⁄

16, 17

⁄

Carrier (52F Series) }or 22

General Electric/

Hotpoint 26 15

⁄

Whirlpool 25

⁄

or 23

Fedders/Emerson 27 16

⁄

or 19

⁄

Sears/Kenmore 25

⁄

Emerson/Fedders 26

⁄

Carrier (51S Series) 25

⁄

Friedrich 27 16

⁄

NOTE:All wall sleeves used to mount the new Air

Conditioner must be in sound structural condition and

have a rear grille that securely attaches to sleeve, or

rear flange that serves as a stop for the Air Conditioner.

CAUTION: When installation is complete, replacement

unit MUSThave a rearward

slope as shown.

2. Remove old Air Conditioner from wall sleeve and

prepare wall sleeve as follows:

— Clean interior (do not disturb seals).

— Wall sleeve must be securely fastened in wall before

installing Air Conditioner. Drive more nails or screws

through sleeve, into wall, if needed.

— Repair paint if needed.

3. If not existing, drill a 3/16"clearance hole for ground-

ing screw through left side of wall sleeve, in a clear area

about 3 inches maximum (to suit) back from front edge

of sleeve as shown below. Next attach ground wire

inside sleeve, using grounding screw and nut. Pull loose

end of ground wire out front of sleeve, and temporarily

bend it down and around lower edge of sleeve.

Wall sleeve to unit

sleeve grounding

4. Prepare the wall sleeve for installation of the new unit

per the following Brand instructions.

#1 Emerson 15"Deep

#2 Fedders 19

⁄

"Deep

#3 Fedders or Friedrich 16

⁄

"Deep

#4 General Electric/Hotpoint 16

⁄

"Deep

#5 Sears or Carrier (51S Series) 18

⁄

"Deep

#6 Whirlpool 17

⁄

"Deep

#7 Whirlpool 23"Deep

#8 White-Westinghouse/Frigidaire/ 16"+ 17

⁄

"Deep

Carrier (52F Series)

#9 White-Westinghouse/Frigidaire 22"Deep

5. Install new unit into wall sleeve.

6. To attach ground wire to the new unit, remove the

screw from the left side front.

7. Assemble and install the

Trim Frame (see instruction).

Part No. 309000913

(852-101)

Installation Instructions:

REAR

UNIT

FRONT

LEVEL

1/4” to 5/16”

Wall

Sleeve

Max.

3/16"

Hole

Wall Sleeve Brands:

Rear Louvers

60°10-1/4" 60°

Top View

#1 Emerson 15"Deep

1. Redirect the louvers at the back of the wall sleeve as shown in the

illustration. The use of pliers is recommended.

2. Attach (1) 1

⁄

"x 3/8"x 26

⁄

"long seal as shown in the illustration.

3. Attach the (2) 1

⁄

"x 3/8"x 14"long seals, to the inside of the

louvered pane. Install the seals as shown in the illustration.

4. Cut the 1

⁄

"x 3/8"x 26

⁄

"long seal to 14"long, and attach it to the

inside of the louvered panel as shown in the illustration. Attach the

(2) 4

⁄

"x 3

⁄

"x 1

⁄

"Centering/Support Blocks, one on each side wall,

to the inside of the sleeve with the Tappered End facing the opening.

These (2) blocks should be locaed approximately in the center of the

side walls. To attach the blocks remove the backing paper from the

blocks. Do not touch adhesive on the blocks. Press the blocks firmly

in place.

5. Install the new unit into the wall sleeve.

6. Attach the ground wire to the unit as shown.

7. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve

and the unit. Aflat bladed screwdriver or putty knife is recommended.

8. Assemble and install the Trim Frame. (see Trim Frame)

←101⁄4"‹→

Trim Frame Assembly The purpose of trim frame is to cover space between wall sleeve

and replacement unit cabinet. Each frame is made of four parts:

1. To assemble trim frame, insert snaps of side legs into top and bottom

legs.

2. To install trim frame to sleeves, slide frame over cabinet until it is

flush with the wall sleeve.

NOTE: Be sure to route the cord through the trim frame before

placing the trim frame on the unit.

Wall Sleeve Brands: #9 White-Westinghouse or Frigidaire 22"Deep

1. If the wall sleeve does not have a rear grille or louvered panel, install

the plastic grille panel from the kit. The plastic grille panel is mounted

to the inside of the wall sleeve at the rear flanges. There are (4)

plastic nuts in the flanges of the wall sleeve. If your sleeve is missing

these nuts or they are damaged, replacement nuts and grille

mounting screws are supplied with the kit. The nuts are installed

from the inside of the sleeve and are pressed into the square holes

of the rear flanges. Place the grille against the rear flanges and use

the (4) washer screws to secure the grille to the sleeve.

2. Attach the (2) 4

⁄

"x 3

⁄

"x 1

⁄

"foam blocks to the inside of the wall

sleeve as shown in the illustration.

3. Attach 1"x 3/4"x 14"long seal to the inside of the grille panel.

4. Cut the 1/8"x 4

⁄

"x 14

⁄

"long plastic divider to 13"long.

Slide the plastic divider in the slots of the (2) foam blocks.

5. Cut to fit (1) 1

⁄

"x 1

⁄

"x 26

⁄

"long seals as shown.

6. Attach (2) 1

⁄

"x 1

⁄

"x 14"long seals to 13

⁄

"install the seals as

shown. Seals should be flush with front portion of the 4

⁄

"x 3

⁄

"foam blocks which holds the plastic divider.

8. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve and the unit.

Aflat bladed screwdriver or putty knife is recommended.

7. Install the new unit into the wall sleeve.

Attach the ground wire to the unit as shown.

←91⁄2"‹→

9. Assemble and install the Trim Frame.

(see Trim Frame)

Wall Sleeve Brands:

Rear Louvers

60°10-1/2" 60°

Top View

#2 Fedders 19

⁄

"Deep

1. Redirect the louvers at the back of the wall sleeve as shown in the

illustration. The use of pliers is recommended.

2. Attach the (2) 4

⁄

"x 3

⁄

"x 1

⁄

"Centering/Support Blocks to the inside

of the walls of the wall sleeve as illustrate with tapered end facing

the opening of sleeve. These (2) blocks should be located

approximately in the center of the side walls. To attach the blocks

remove the backing paper from the blocks. Do not touch adhesive on

the blocks. Press the blocks firmly in place.

3. Cut (2) 17"Tapered Spacer Blocks and install as shown in the

illustration. The 4"portion to be placed in front of the rib on base and

tapered end facing the back of the sleeve. The remaining portion to

be placed behind the rib.

4. Attach (1) 1

⁄

"x 1

⁄

"x 26

⁄

"long seals and the (2) 1

⁄

"x 1

⁄

"x 14"

long seals as shown in the illustration.

5. Cut (1) 1

⁄

'x 1

⁄

"x 26

⁄

"long seal to 14"and attach to inside of the

louvered panel as shown in the illustration.

6. Install the new unit into the wall sleeve.

8. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve

and the unit. Aflat bladed screwdriver or putty knife is recommended.

9. Assemble and install the Trim Frame.

(see Trim Frame)

7. Attach the ground wire to the unit as

shown.

Cut Here

3/4"

17"

Protection Paper Backing

Tapered Spacer Block

←101⁄2"‹→

←61⁄2"‹→←61⁄2"‹→

Wall Sleeve Brands:

Rear Louvers

60°10-1/2" 60°

Top View

#3 Fedders or Friedrich 16

⁄

"Deep

1. Redirect the louvers at the back of the wall sleeve as shown in the

illustration. The use of pliers is recommended.

2. Attach (2) 4

⁄

"x 3

⁄

"x 1

⁄

"Centering/Support Blocks to the inside of

the walls of the wall sleeve as illustrated with tapered end facing the

opening of the Sleeve. These (2) blocks should be located

approximately in the center of the side walls. To attach the blocks

remove the backing paper from the blocks. Do not touch adhesive on

the blocks. Press the blocks firmly in place.

3. Cut (2) 17"Tapered Spacer Blocks and install as shown in the

illustration. The 4"portion to be placed in front of the rib on base and

tapered end facing the back of the sleeve. The remaining portion to

be placed behind the rib. The 2

⁄

"portion to be placed in front of the

rib on the base with the tapered end facing the back of the sleeve.

Cut the remaining portion to 12

⁄

"and place behind the rib with the

tapered end facing the back of the sleeve.

4. Attach (1) 1

⁄

"x 1

⁄

"x 26

⁄

"long seals and the

(2) 1

⁄

"x 1

⁄

"x 14"long seals as shown in the illustration.

5. Cut (1) 1

⁄

"x 1

⁄

"x 26

⁄

"long seal to 14"and attach inside of the

louvered panel as shown in the illustration.

7. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve and the unit.

Aflat bladed screwdriver or putty knife is recommended.

6. Install the new unit into the wall sleeve.

Attach the ground wire to the unit as shown.

8. Assemble and install the Trim Frame.

(see Trim Frame)

Cut Here

3/4"

17"

Protection Paper Backing

Tapered Spacer Block

12-1/2"12-1/2" 2-1/2"

←101⁄2"‹→

←61⁄2"‹→←61⁄2"‹→

Wall Sleeve Brands: #8 White-Westinghouse/Frigidaire/ 16"+ 17

⁄

"Deep

Carrier (52F Series)

1. If the wall sleeve does not have a rear grille or louvered panel, install

the plastic grille panel from the kit. The plastic grille panel is mounted

to the inside of the wall sleeve at the rear flanges. There are (4)

plastic nuts in the flanges of the wall sleeve. If your sleeve is missing

these nuts or they are damaged. Replacement nuts and grille

mounting screws are supplied with the kit. The nuts are installed

from the inside of the sleeve and are pressed into the square holes

of the rear flanges. Place the grille against the rear flanges and use

the (4) washer screws to secure the grille to the sleeve.

2. Cut and attach the (1) 1

⁄

"x 3/8"x 26

⁄

"long seal to 25

⁄

"long.

Attach (2) 1

⁄

"x 3/8"x 14"long seals as shown. To attach the seals

remove the backing paper from the seal. Do not touch adhesive.

Press seals firmly in place.

3. Attach 1"x 3/4"x 14"long seal to the inside of the grille panel as

shown in the illustration.

5. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve

and the unit. Aflat bladed screwdriver or putty knife is recommended.

6. Assemble and install the Trim Frame. (see Trim Frame)

4. Install the new unit into the wall sleeve.

Attach the ground wire to the unit as shown.

← 91⁄2→

Wall Sleeve Brands:

Rear Louvers

60°10" 60°

Top View

9-1/2"

#7 Whirlpool 23"Deep

1. Redirect the louvers at the back of the wall sleeve as shown in the

illustration. The use of pliers is recommended.

2. Attach the (2) 4

⁄

"x 3

⁄

"x 1

⁄

"foam blocks to the inside top and bot-

tom of the wall sleeve with the slots 10"from the right side wall of the

sleeve. Attach (2) Tapered Spacer Blocks behind rib on inside bottom

of the wall sleeve as shown. Taper towards the rear of the sleeve.

3. Attach 1"x 3/4"x 14"long seal to the inside of the grille panel.

4. Install the 1/8"x 4

⁄

"x 14"long plastic divider to the 13

⁄

"long.

Slide the plastic divider in the slots of the (2) foam blocks.

5. Cut to fit (1) 1

⁄

"x 1

⁄

"x 26

⁄

"long seals as shown.

Attach (2) 1

⁄

"x 1

⁄

"x 14"long seals. Install the seals as shown.

Seals should be flush with front side of 4

⁄

"x 3

⁄

"x 1

⁄

"Foam Blocks

which holds the plastic divider.

6. Install the new

unit into the wall

sleeve. Attach

the ground wire

to the unit as

shown.

3/4"

17"

Tapered Spacer Block

9. Assemble and install the Trim Frame. (see Trim Frame)

7. Install the 1"x 1

⁄

'x 84"long stuffer seal between the wall sleeve

and the unit. Aflat bladed screwdriver or putty knife is recommended.

←10"‹→

←14"‹ →← 8"‹→

←61⁄2"‹→←61⁄2"‹→

Wall Sleeve Brands:

Rear Louvers

60°11"60°

Top View

#4 General Electric/Hotpoint 16

⁄

"Deep

1. Redirect the louvers at the back of the wall sleeve as shown in the

illustration. The use of pliers is recommended.

2. Cut (2) 17"Tapered Spacer Blocks to 13” and install as shown in the

illustration with the tapered end

⁄

"from the back of the sleeve.

3. Cut (1) 1

⁄

"x 3/8"x 26

⁄

"long seals to 25"long attach as shown.

Attach (2) 1

⁄

"x 3/8"x 14"long seals as shown in the illustration.

4. Attach 1"x 3/4"x 14"long seal to the louvered panel as shown in the

illustration.

6. Install the 1"x 1

⁄

"x 84"long stuffer seal between the wall sleeve and the unit.

Aflat bladed screwdriver or putty knife is recommended.

5. Install the new unit into the wall sleeve.

Attach the ground wire to the unit as shown.

7. Assemble and install the Trim Frame.

(see Trim Frame)

Cut Here3/4"

17"

13"

Protection Paper Backing

Tapered Spacer Block

←101⁄2"‹→

←61⁄2"‹→←61⁄2"‹→

101⁄2”

Other manuals for FAH12EN2T

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FRA084KT7 Quick start guide

Frigidaire

Frigidaire Designer Series User manual

Frigidaire

Frigidaire FRS18PYS2 User manual

Frigidaire

Frigidaire FRA102BT112 User manual

Frigidaire

Frigidaire FAS254J2A2 User manual

Frigidaire

Frigidaire FAH10EM2T1 Quick start guide

Frigidaire

Frigidaire FAH12EN2T3 Quick start guide

Frigidaire

Frigidaire FFPA1422R1 Owner's manual

Frigidaire

Frigidaire FAC122P1 User manual

Frigidaire

Frigidaire FAK085Q7V1 User manual

Frigidaire

Frigidaire FAC065J7A3 User manual

Frigidaire

Frigidaire FFTA1233Q25 Owner's manual

Frigidaire

Frigidaire P/N 66121617 User manual

Frigidaire

Frigidaire FRA084KT7 User manual

Frigidaire

Frigidaire Home Comfort FRA082AT7 Installation instructions

Frigidaire

Frigidaire FAH10EN2 User manual

Frigidaire

Frigidaire FAH106S1T - 10000 BTU Through-the-Wall Air... User manual

Frigidaire

Frigidaire CRA102BT110 Owner's manual

Frigidaire

Frigidaire FRA144HT2 Installation instructions

Frigidaire

Frigidaire FAH126N2T1 Service manual

Frigidaire

Frigidaire FAS297Q2A2 Quick start guide

Frigidaire

Frigidaire FFRZ0633Q13 Owner's manual

Frigidaire

Frigidaire FAX050S7AF User manual

Frigidaire

Frigidaire FAS156N1 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions