Frigidaire FFRS0833Q1 User manual

READ BEFORE INSTALLING UNIT

For Slider Casement Air Conditioners

Installation Instructions

NOTE:

These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or

installation in a metal CASEMENT window. Modification may be necessary when installing in windows made

differently than those shown in these instructions.

WARNING:

Electrical ground is required on this appliance.

DO NOT ground to a gas line.

If cold water pipe is interrupted by plastic, non-metallic gaskets, or other insulating materials, DO NOT use for

grounding.

Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.

DO NOT modify power supply cord plug. If it does not fit outlet, have a proper outlet installed by a qualified

electrician.

DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral, or grounding circuit could result in

an electrical shock.

DO NOT use an extension cord with this appliance.

Meeting Electrical Requirements

OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES. DO NOT, UNDER ANY CIRCUMSTANCES,

NOTE:

If codes permit, and a separate grounding wire is used, it is recommended that a qualified electrician determine

that the grounding path is adequate and not interrupted by plastic, non-metallic gaskets, or other insulating

materials.

be exposed:

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended

period of time.

Make sure air conditioner does not fall during installation.

Carefully read the installation manual before beginning.

Follow each step as shown.

INSTALLATION WARNINGS AND CAUTION

Installation Instructions

Receptacle Wiring:

Receptacle wiring should be a minimum of 14 gauge. Use copper wire only. It is your responsibility to provide proper

and adequate receptacle wiring, installed by a qualified electrician.

Electrical Requirements:

A 115 volt (103.5 minimum, 126.5 maximum), 60 Hertz, AC only, 15 ampere fused electrical supply is required. A time

delay fuse or time delay circuit breaker is also required. A separate circuit, serving this appliance only, MUST be

provided.

Electrical Connection:

Electrical grounding is required on this appliance.

Recommended grounding method:

For your personal safety, this appliance must be grounded.

This air conditioner includes a power supply cord with a

3-prong grounding plug. To minimize possible electrical shock

hazard:

cord must be plugged into a matching 3-prong grounding type

wall receptacle.

must be grounded in accordance with National Electrical

Code (ANSI/NFPA 70-latest version) and all local codes and

ordinances.

If a matching 3-prong grounding type wall receptacle is not available,

it is the responsibility of the consumer to have a properly grounded

3-prong wall receptacle installed by a qualified electrician.

3-Prong Grounding

Type Wall Receptacle

3-Prong

Grounding plug

Grounding prong

Power Supply Cord

(6 feet long)

Preparing for Installation

Installation Tips

For wood-frame casement windows:

It may be necessary to construct a frame, using at least

ƎWKLFNZRRGZLWKDƎZLGHRSHQLQJ

For brick or cement building construction:

It may be necessary to put a wood stool strip under air

conditioner, for mounting purposes as shown FIG. 2.

WARNING:

Because this unit weighs about 60 to 80 pounds, it is recommended that you have someone help you when

installing your new unit, and that you both use proper lifting techniques. Inspect the condition of the window

where unit will be installed. Be sure it will support the weight of the unit.

This appliance must be installed according to all applicable codes and ordinances.

Failure to adhere to the following precautions could result in personal injury and product damage.

Handle air conditioner with care. AVOID sharp metal fins on front and rear coils.

Make sure your air conditioner does not fall during installation.

Do not use water collected in the unit for drinking purposes. It is not sanitary.

Flat-head screwdriver

Phillips-head screwdriver

Tools Required

Carpenter’s level

Tape measure

Fine tooth saw

Electric or hand drill

Knife and scissors

Pencil

NOTE:

DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED IN THESE INSTRUCTIONS.

inner sill

OUTDOORINDOOR

outer sill

Bottom Rail of

air conditioner

wood strip

mounted on

top of inner sill

FIG. 1

FIG. 2

Installation Instructions

Make sure you have all the necessary parts.

Installation kit contents (FIG.3):

Hardware

Side channel seal

Support brace

Platform

Adjustment bolt

Hex flange nut - 1/4

Track seal

Window sash seal

Safety bracket

Qty.

No.

Qty.

Hardware

Window locking bracket

Plastic window panel

Side channel

Panel frame/seal assembly

No.

Support bracket

(For Vinyl-Clad windows)

Safety bracket

(For Vinyl-Clad windows)

39 or 10

or 11 or 17

NOTE:

Use scale below to measure length of your screws. The scale will come in handy

when separating screws for installation.

IDENTIFY SCREWS

BY LENGTH

(13mm) (25mm) (44mm) (63mm)

(10mm) (19mm) (38mm) (50mm)

NOTE:

Height measurement must be of a clear opening above mounting platform.

In some cases, due to a variety of stop and track arrangements, the above

dimensions may vary slightly. If necessary, installation can be made by

alternating window jambs. (See Alternate Window Jamb Applications.)

FIG.3

minimum

width

minimum

height

maximum

height

maximum

Ǝ

Ǝ

Ǝ

Ǝ

width

(casement

windows)

FIG.4

Choose a proper sized window, as shown (FIG.4).

ƎPLQLPXPZLGWK

ƎPD[LPXPZLGWKIRUFDVHPHQWZLQGRZV

ƎPLQLPXPKHLJKWZLWKZLQGRZSDQHOUHWDLQHU

ƎPLQLPXPKHLJKWZLQGRZSDQHOUHWDLQHUUHPRYHG

Ǝmaximum height

Choose the proper window location.

Choose a window that allows the cooled air to flow freely and directly into

room(s) you wish to cool. Remember, it is difficult to move air around

corners. Also, choose a window that is within 6 feet of an electrical outlet

as shown (FIG.5). (See Meeting Electrical Requirements/Receptacle wiring

needs.) Do not use an extension cord.

6 feet

power cord

reach

FIG.5

Inside wall

of house

Siding-protection

board

Apply track seal

to window side

of track.

FIG.9

FIG.8A

with platform tab pressed

against window track

Center platform

assembly on the line

Attach support brace to platform as shown (FIG.6). Use adjustment

bolt and hex flange nut to complete assembly. Choose slot and adjustment

bolt hole locations that will create a 45 degree angle between platform and

support brace. Try assembly in the window to determine if platform will rest

SURSHUO\DQGDOORZSURSHUVORSHƎORZHURQRXWVLGH

Center platform assembly on the line with inside platform tab

pressed against inside edge of window track as shown (FIG.8A, FIG.8B).

8VLQJWKHKROHVLQWKHSODWIRUPDVDJXLGHPDUNDQGGULOOWZRƎGLDPHWHU

holes. Drill holes in either track or stool.

Peel off protective backing from track seal. Apply seal to room side

of window track (FIG.9). Center of seal strip should coincide with the line

marked in Step 5. The two screw holes drilled in Step 6 should be directly

above seal strip in the inner track.

Securely attach a siding-protection board to side of house (FIG.10).

NOTE: Siding-protection board should be long enough to span 2 wall studs.

Installation Instructions

Installing Unit in a Sliding Window:

NOTE:

If you are planning to use a siding-protection board (see Step 8) on the

outside of your house, hold board in place when testing assembly in window.

NOTE:

,IDQ\VDVKVWRSSURWUXGHVPRUHWKDQƎIURPWKHVLGHZLQGRZMDPEVWKH

ƎPHDVXUHPHQWPXVWEHLQFUHDVHGDFFRUGLQJO\),*6FUHHQDQG

storm window frames may also require adjustments to the measurement.

For vinyl-clad windows, you need to install the support bracket on the

window track before you install the platform. Follow the instructions below to

do that.

1. Place the support bracket on the window sill as shown (FIG.8C). Using the

holes in the support bracket as a guide, mark and drill two 1/8" diameter holes.

)ROORZ6WHSWRDSSOO\WKHWUDFNVHDORQWKHURRPVLGHRIZLQGRZWUDFN

$IWHUDSSOO\WKHWUDFNVHDOXVHWZRVFUHZLWHPWRIL[LQJWKHVXSSRUW

bracket. Make sure the support bracket is level form side to side.

Proceed to Step 9 after you finish fixing the support bracket.

Platform Assembly

FLANGE NUT

ƎPP+(;

FIG.6

ƎLQFKHVFIG.7

window track window seal

Alternate screw location

(depending on the inner sill depth)

Platform tab FIG.8B

FIG.10

MHDVXUHDQGOLJKWO\PDUNDOLQHƎIURPZLQGRZMDPE

ƎLQFKHV FIG.8C

Alternate the screw

location (depending on

the height of the sill)

Installation Instructions

To remove front as shown (FIG.16)

1. Remove the two front retaining screws from the front frame.

2. Press firmly on each side of the metal case close to front, approximately 2/3 of the way down.

3. While pressing on the sides of the metal case, gently pull the front out and lift up to release it from the case.

4. Then release the electrical coupler plug.

Place air conditioner in window opening. As shown (FIG.17), it should sit on platform assembly so that

window panel frame and cabinet side channels are against top and side window jambs.

2XWVLGHHGJHLVƎ

lower than inside.

Put platform

tab against

inside of track.

FIG.11A

Measure

distance

and

subtract

Ǝ

FIG.12

Panel frame

Plastic

window panel

FIG.14

Apply side

channel seal

to side channels

just below edge

of panel frame

FIG.15

NOTE: DO NOT push or pull air direction louvers.

Front

Retaining

Screw

FIG.16

Slide inner

window sash

firmly against

cabinet.

FIG.17

Adjust platform assemblyVRWKDWRXWVLGHHGJHLVƎORZHUWKDQ

inside edge, as shown (FIG.11A & FIG.B). This ensures proper water drainage

from the air conditioner.

Level platform assembly from side-to-side. Also, make sure window

track is level. Use leveling shims as necessary to ensure unit is level from

side-to-side.

Measure height of window opening from top of platform assembly as

VKRZQ),*6XEWUDFWƎ0DUNWKLVPHDVXUHPHQWRQSODVWLFZLQGRZ

panel, along the longer side.

Clamp plastic window panel between a board and a work table, and

cut along cutting line with a fine tooth saw. Remove any burrs with a file.

Fasten side channels to the sides of the air conditioner using 3 screws

(Item 17) per channel as shown (FIG.13). Start with first screw at top of

channel. Make sure hook ends of channels face toward back of unit.

Slide plastic window panel into panel frame as shown (FIG.14),with

the smooth side to the room. Slide panel frame assembly into side channels

of the AC cabinet. Make sure plastic window panel is firmly enclosed on all

sides by the retainer grooves.

Cut side channel seal into 2 equal lengths. Remove protective backing

and apply it to the rear side of cabinet side channels, starting just below panel

frame assembly (FIG.15). Pinch off excess length so seal is even with the bottom

of the cabinet side channel.

Place platform assembly, with platform tab against inside of window

track, and attach it to window jamb (FIG.11A). Use appropriate length

screws (Items 9-11 in preparing For Installation).

For Vinyl- Clad windows, place platform assembly, with platform tab

against insidh edge of the support bracket, and use two 3/8" screw (item 17)

to attache it to support bracket as shown (FIG.11B).

FIG.11B

Put platform tab

against inside edge

Outside edge is 3/16”

lower than inside.

Fastening

Side Channels

FIG.13

FIG.18

Installation Instructions

Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window

track and cabinet side channels. If the panel frame does not fit snugly to the inner window sash, secure the panel frame

WRWKHVDVKZLWK[ƎVHOIWKUHDGLQJVFUHZV8VHWKHSDUWLDOO\SOXJJHGKROHVLQWKHSDQHOIUDPH'ULOOƎSLORW

holes for the screws.

Hook the safety bracket overWKHEDVHRIWKHXQLWDQGIDVWHQLWWRWKHIURQWRIWKHSODWIRUPDVVHPEO\),*8VH

D[ƎVHOIWKUHDGLQJVFUHZ

NOTE:7KHEUDFNHWSUHYHQWVPRYHPHQWRIWKHDLUFRQGLWLRQHUHLWKHULQRURXWDIWHUFRPSOHWLQJWKHLQVWDOODWLRQ

Stuff the window sash sealEHWZHHQWKHYHUWLFDOVDVKDQGWKHZLQGRZJODVVDVVKRZQ),*

Use the window locking bracketWRORFNWKHLQQHUZLQGRZVDVKWRWKHEDVHRIWKHRXWHUZLQGRZVDVK),*

8VHRQH[ƎVFUHZRU[ƎVHOIWKUHDGLQJVFUHZ'ULOOƎSLORWKROH

To replace the front first reconnect the coupler plugs, make the exhaust control positioned through the front in

the proper location. Gently push the front into position on the cabinet. It should click into place. Then replace the

retaining screws that holds the panel in place. DO NOT push or pull the front panel louvers.

Insttall safety bracket

window sash seal

Window

locking

bracket

To install in windows having no flanges or wood stops on the top and side jambs, the channels and panel frame must

ILWDJDLQVWDPDWFKLQJIODQJHRUƎPD[WKLFNDQJOHDWWDFKHGWRWKHZLQGRZMDPEV),*$VKRZVWKLVDQJOH

LQVWDOOHG),*%),*&VKRZDOWHUQDWHWUHDWPHQWV2QWKHVDVKVLGHRIWKHRSHQLQJWKHOHDGLQJFRUQHURIWKHLQQHU

sash becomes the flange. You can purchase the angle strip locally.

Alternate Window Jamb Applications

),*&

),*$ ),*%

$GGDQJOHWRZRRGVWRS $GGZRRGDVVKRZQ $GGRUJDJHDQJOH

Room

´RU´

Room

´[³RU

3/4”x3/4”

angle

Installing the Unit in a Casement Window

NOTE:

2SHQWKHZLQGRZWKHPD[LPXPDPRXQWWRDOORZIRUFOHDUDQFHRIWKHFDELQHW

The crank handle should be removed to allow the platform to be fastened to

WKHMDPE,IWKHZLQGRZFDQQRWRSHQIDUHQRXJKPRUHWKDQƎIRUWKH

cabinet to clear the window, remove the window entirely by drilling out the

ULYHWV%ROWVFDQVHUYHDVWKHSLYRWVLQWKHIHDWXUH

To avoid crank handle and window clearance problems, the unit can be

installed in a stationary sash section. However, the horizontal mullion and

WKHJODVVSDQHOVPXVWEHUHPRYHGEHIRUHLQVWDOODWLRQ

Attach support brace to platformDVVKRZQ),*8VHWKHDGMXVWPHQWEROW

DQGKH[IODQJHQXWWRFRPSOHWHWKHDVVHPEO\&KRRVHWKHVORWDQGDGMXVWPHQWEROW

KROHORFDWLRQWKDWZLOOFUHDWHDGHJUHHDQJOHEHWZHHQWKHSODWIRUPDQGVXSSRUW

brace. Try the assembly in the window to determine if the platform will rest properly,

DQGDOORZWKHSURSHUVORSHƎORZHURQRXWVLGH

FIG.19

Room

´RU´

Flush

3ODWIRUP$VVHPEO\

´PP+(;

)/$1*(187

),*

safety bracket

(choose the correct

safety bracket

according to your

ZLQGRZW\SH

)RU9LQ\O&ODGZLQGRZVXVH,WHPUHIHUWRSDJHWRIDVWHQWKHXQLWWRWKHSODWIRUP

Installation Instructions

NOTE:

If you are planning to use a siding-protection board (see Step 29) on the outside of your house, hold the board in

place when testing the assembly in the window.

Equal distance from both sides Apply track seal to the outside

edge of the bottom window jamb. Track seal

Window jamb

Screw

NOTE:

A projection below the base of the air conditioner will require the rear of the platform to be 7/16” lower than the

front to create the 3/16” slant from front to rear (FIG.25) .

Measure the height of the window opening from the top of the platform

DVVHPEO\DVVKRZQ),*6XEWUDFWƎ0DUNWKLVPHDVXUHPHQWRQWKH

plastic window panel, along the longer side.

Clamp the plastic window panel between a board and a work table, and

cut along the cutting line with a fine tooth saw. Remove any burrs with a file.

Fasten the side channels to the sides of the unit using three screws

,WHPSHUFKDQQHO0DNHVXUHKRRNHQGVRIFKDQQHOVIDFHWRZDUGWKHEDFN

of unit.

Slide the plastic window panel into the panel frame with the smooth

side to the room. Slide the panel frame assembly into the side channels of

WKHDLUFRQGLWLRQHUFDELQHW0DNHVXUHWKHSODVWLFZLQGRZSDQHOLVILUPO\

enclosed on all sides by the retainer grooves (FIG.28).

FIG.22 FIG.23 FIG.24

Fasten siding

protection board to

the house siding.

Rear is at least

7/16” lower than

front

FIG.25 FIG.26

0HDVXUH

distance

and

subtract

Ǝ

FIG.27

Panel frame

Plastic window panel

FIG.28

'ULOODƎGLDPHWHUSLORWKROH in the window jamb an equal distance from each side of the jamb (FIG.22),

DQGƎXSIURPWKHZLQGRZVLOO,IWKHKROHFRLQFLGHVZLWKWKHZLQGRZOHYHUVORWLQWKHMDPEERWWRPDQDGGLWLRQDOKROH

will have to be drilled through the platform edge and the window jamb to miss this slot.

Peel off the protective backing from the track seal, and stick the seal to the window sill on the outside of the

bottom jamb as shown (FIG.23).

Screw the platform assembly to the window jamb WKURXJKWKHSLORWKROH\RXGULOOHGLQ6WHS8VHD[Ǝ

self-threading screw (FIG.24).

Adjust the platform assembly VRWKDWWKHUHDURIWKHDLUFRQGLWLRQHUZLOOEHƎORZHUWKDQWKHIURQWWLOWHGDERXW

2° to 4° downward to the outside). After proper installation, condensate should not drain from the overflow drain hole

during normal use, correct the slope otherwise.

Securely attach a siding-protection board to the side of the house where the platform assembly hit the house

as shown (FIG.26). The siding-protection board should be long enough to span 2 wall studs.

9/64ƎGLDPHWHU

pilot hole

Installation Instructions

Cut side channel seal into 2 equal lengths. Remove the protective backing and apply it to the rear side of the

cabinet side channels, starting just below the panel frame assembly. Pinch off excess length so the seal is even with

the bottom of the cabinet side channel (FIG.29).

To remove front as shown (FIG.30)

1. Remove the two front retaining screws from the front frame.

2. Press firmly on each side of the metal case close to the front, approximately 2/3 of the way down.

3. While pressing on the sides of the metal case, gently pull the front out and lift up to release it from the case.

4. Then release the electrical coupler plug.

NOTE: DO NOT push or pull air direction louvers.

Place the air conditioner in the window opening as shown (FIG.31). It should sit on the platform assembly

so that the window panel frame and the cabinet side channels are against the top and side window jambs. Side

channels should overlap side window jambs equally.

Apply side

channel

seal to side

channels just

below edge of

panel frame.

Front

Retaining

Screw

'ULOOWZRƎGLDPHWHUSLORWKROHVin the top window jamb in line with the partially plugged holes in the panel

IUDPH6HFXUHWKHSDQHOIUDPHWRWKHZLQGRZMDPEZLWKWZR[ƎVHOIWKUHDGLQJVFUHZV,IDGGLWLRQDOKROGLQJLV

necessary, two screws may be used on the sides of the panel frame as well.

Drill two screw-clearance holes LQWKHFDELQHWVLGHFKDQQHOVQHDUERWWRPDQGWZRƎGLDPHWHUSLORWKROHV

LQWKHVLGHZLQGRZMDPEV6HFXUHWKHFDELQHWVLGHFKDQQHOVWRWKHZLQGRZMDPEVZLWKWZR[ƎVHOIWKUHDGLQJ

screws. When doing this, be careful not to twist the side channel seals with the screws.

NOTE: Inserting screws will prevent the air conditioner from being pushed into the room.

To replace the front first reconnect the coupler plugs, make the exhaust control positioned through the front

in the proper location. Gently push the front into position on the cabinet. It should click into place. Then replace the

retaining screws that holds the panel in place.

Do not push against or pull upon the front panel louvers.

FIG.29 FIG.30 FIG.31

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FAH086J1T1 User manual

Frigidaire

Frigidaire FAS255J2A1 User manual

Frigidaire

Frigidaire Split Type Room Air Conditioner User manual

Frigidaire

Frigidaire FAS155M1A1 User manual

Frigidaire

Frigidaire FRA083AT7 User manual

Frigidaire

Frigidaire FAS185M2A1 User manual

Frigidaire

Frigidaire FAS254J2A2 User manual

Frigidaire

Frigidaire FAH12EJ2T1 User manual

Frigidaire

Frigidaire FAC084K7A1 User manual

Frigidaire

Frigidaire FAK104R1V11 User manual

Frigidaire

Frigidaire FRA126CT15 Owner's manual

Frigidaire

Frigidaire FAC082M7A1 User manual

Frigidaire

Frigidaire FAX054P7A14 User manual

Frigidaire

Frigidaire FAK103J1V4 User manual

Frigidaire

Frigidaire FAA055P7 User manual

Frigidaire

Frigidaire FAH126N2T1 Service manual

Frigidaire

Frigidaire FAD052M7A1 User manual

Frigidaire

Frigidaire FRA12EZT2 User manual

Frigidaire

Frigidaire FRA08PZU110 Owner's manual

Frigidaire

Frigidaire FAH106J2T2 User manual

Frigidaire

Frigidaire FAA074S7A12 User manual

Frigidaire

Frigidaire 66121613 User manual

Frigidaire

Frigidaire FAC105L1A1 User manual

Frigidaire

Frigidaire FAK123N1V Quick start guide

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions