Frigidaire FAK127P1V User manual

Installation Instructions

for Slider Casement

NOTE: These instructions describe installation

in a typical wood framed window with a wood

SLIDE-BY sash, or installation in a metal

CASEMENT window. Modification may be

necessary when installing in windows made

differently than those shown in these instructions.

A high window accessory kit EA 103W is available

for window heights up to 62" (1575mm).

TABLE OF CONTENTS

SUBJECT PAGE

Meeting Electrical Requirements 1

Electrical Connection 2

Preparing for Installation 2

Sliding Window Installation 4

Casement Window Installation 5

Installation in Wood Window 6

Meeting Electrical Requirements

WARNINGWARNING

Electrical Shock and Personal Injury Hazard

Electrical ground is required on this appliance.

DO NOT ground to a gas line.

If cold water pipe is interrupted by plastic,

non-metallic gaskets, or other insulating.

Materials, DO NOT use for grounding.

Check with a qualified electrician if you are in

doubt as to whether the appliance is properly

grounded.

DO NOT modify power supply cord plug. If it

does not fit outlet, have a proper outlet

installed by a qualified electrician.

DO NOT have a fuse in the neutral or grounding

circuit. A fuse in the neutral, or grounding

circuit could result in an electrical shock.

DO NOT use an extension cord with this

appliance.

Failure to follow these instructions could result

electrical shock, serious injury, or death.

OBSERVE ALL LOCAL GOVERNING CODES

AND ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE

THE POWER SUPPLYCORD GROUNDING PRONG.

NOTE: If codes permit, and a separate grounding

wire is used; it is recommended that a qualified

electrician determine that the grounding path is

adequate and not interrupted by plastic, non-metallic

gaskets, or other insulating materials.

RECEPTACLE WIRING

Receptacle wiring should be a minimum of 14 gauge.

Use copper wire only. It is your responsibility to

provide proper and adequate receptacle wiring,

installed by a qualified electrician.

ELECTRICAL REQUIREMENTS

A 115 volt (103 minimum, 126 maximum), 60 Hertz,

AC only, 15 ampere fused electrical supply is

required. A time delay fuse or time delay circuit

breaker is also required. A separate circuit, serving

only this appliance, MUST be provided.

P/N

Electrical Connection

Electrical ground is required on this appliance.

Recommended grounding method:

For your personal safety, this appliance must be

grounded. This air conditioner includes a power

supply cord with a 3-prong grounding plug. To

minimize possible electrical shock hazard:

-cord must be plugged into a mating 3-prong

grounding-type wall receptacle,

-must be grounded in accordance with

National Electrical Code (ANSI/NFPA 70-

latest version) and

-all local codes and ordinances.

If a mating 3-prong grounding-type wall

receptacle is not available, it is the responsibility

of the consumer to have a properly grounded

3-prong wall receptacle installed by a qualified

electrician.

Preparing for Installation

Installation Tips

For wood-frame casement windows: It may be

necessary to construct a frame, using at least

1-inch thick wood, with a 15-1/2-inch wide

opening.

For brick or cement building construction: It

may be necessary to put a wood stool strip under

AC, for mounting purposes.

Tools Required

Flat-head screwdriver

Phillips-head screwdriver

Carpenter's level

Tape measure

Fine tooth saw

Electric or hand drill

Knife and scissors

Pencil

NOTE: A damaged power supply cord CANNOT be

repaired-it MUST be replaced with a new power

supply cord obtained from the product

manufacturer.

Do not, under any

circumstances, cut,

remove, or bypass

the grounding prong.

Power supply cord

with 3-prong grounding

plug and current

detection device

Grounding type wall

receptacle

WARNINGWARNING

Avoid fire hazard or

electric shock. Do not use an extension

cord or an adaptor plug. Do not remove

any prong from the power cord.

NOTE: The rating plate on the unit contains

electrical and other technical data. The rating

plate is located on the right side of the unit.

1. Make sure you have all the necessary parts.

Installation kit contents:

3/8"Screws (4)

End Cap &

Leveling Leg (1)

Fig. 1A Installation Hardware Model 463AAC008BA

Nuts(2)

Fig. A Installation Hardware

Washers(2)

1"Screws (2)

Support

platform(1)

Support angles (1)

Speed clips(2) Filler panel(1)

Sliders(2)

Seals (2)

Shorter

seal (1)

7/16" Screws(2)

Topretainer (1)

Foam (1)

2. Choose a proper sized window, as shown right.

15-1/2 inches minimum width

17-1/2 inches maximum width (for casement

windows)

21-1/4 inches minimum height (with window

panel retainer)

20-5/16 inches minimum height (window

panel retainer removed)

40 inches maximum height

NOTE: Height measurement must be of a clear

opening above mounting platform. In some cases,

due to a variety of stop and track arrangements,

the above dimensions may vary slightly. If

necessary, installation can be made by alternating

window jambs. (See Alternate Window Jamb

Applications.)

(continued)

3. Choose the proper window location

Choose a window that allows the cooled air to flow

freely and directly into room(s) you wish to cool.

Remember, it is difficult to move air around corners.

Fig. 3

Awning

Side

obstruction

Ground

Fence,

wall, or

other

obstacle.

12" Min.

30" Min.

20"

Min.

20"

Min.

As shown below:

20 inches

minimum

height

40 inches

maximum

height

516

15 inches

minimum

width

17 inches

maximum

width

(Casement

window)

Leveling bolt

Support angle

Support

platform

Machine screws

Support platform

assembly

Lower window

track

1.Choose the installation site. It is imperative that window

frame assembly and side of structure are adequate to

support weight ofunit. Reinforce ifnecessary.

2.Slide openone window sashto install supportplatform.

3.Loosely attach support angle to bottom of supportplatform

using two 7/16 g machine screws, flat washers, and

nuts. (See fig.A)

4.Place support platform against lower window track and

firmly against verticaledge of windowframe.

5.Attach support platform to window sill using thre ong

self-tapping screws.To overcome interference of support

platform with windowtrack or stormwindow, securely attach

a 2 wide shim stripto the windowsill. Strip shouldbe as long

as width ofsupport platform and flush with backedge of sill.

Thickness of strip should be controlled by amount of

interference.(See fig. B)

6.Pull support angle against outsideof structure. Tighten two

7/16 long machine screwson top ofsupport platform.

7.Adjust leveling boltto position supportangle in alevel plane.

This willallow for proper unit angle. Tighten leveling bolt

locknut.

” lon

”

e 1”l

Sliding Window Installation

Important: Unit must be level or tilted back slightly to

facilitate proper condensatedrainage. (See fig. C)

Caution: Do notdrill a holein bottom pan.Unit is designed

to operate withapproximate of water inbottom pan.ly 1/2”

8.Cut two pieces of adhesive back foam seal toheight of

window opening. Remove backing and apply to vertical

inside edges of window frame andsliding sash that will

rest against unit.(Seefig. D)

9.Slide unit ontosupport platform. Besure unit sidechannel

butts against verticaledge of windowframe.

Note: If unit side channel doesnot fit securely, remove

unit and readjustleveling bolt.

10.Drill two 1/8 holes through window channel frame in

alignment with existing holes in bottom bar. Install two

3/8 long self-tapping screws through these holes. If

window channel frame is not tallenough to useexisting

holes, drill newholes off to the sideof the existingholes

to attach theunit bottom barto the supportplatform. Unit

should be firmly anchored to window channel fame or

support platform. (Seefig. E)

11.Slide inside window sashclosed. Be surevertical edge

of inside windowsash is pressedfirmly against sideof unit

cabinet. Cut remaining adhesive back foamseal to width

of window opening. Remove backing and apply to top

inside edge ofwindow frame. (Seefig. D)

”

Foam seal Topretainer

Filler panel

Sliders

Three 1”long self-tapping screws

Outside edge is 3/16”

lower than inside.

Solid Piece Wood

(If required)

Casement Window Installation

This air conditioner is designed to fit into most casement type windows.

As shipped from factory, unit will fit into a minimum window opening

15 1/2” wide and 22” high. The preferred method of installation is

through a closed or stationary window. Installation in an open window

frame is also possible where open window can be secured to outside of

building or removed completely.

1.Closed or stationary window: Install unit in stationary sash to avoid

crank handles or window latches. If unit is to be installed in or next to a

movable sash, it may be necessary to remove catch, handle or both.

Remove crank handle and secure window in closed position. Remove

glass panes and separating strips to a height sufficient to mount unit.

2.Open window frame: Remove crank mechanism and catch handles.

Fold window sash back against exterior wall of building and secure, or

remove completely where possible.

3.A filler panel will be required at side of unit when installed in windows

having width greater than 15 1/2". Filler panel should be made from

3/4” thick wood securely anchored to one side of opening so that

15 1/2” wide opening is provided. Filled panel should run full length

of window. Paint to suit.

4. Install unit in same manner as described for sliding windows.

Installation in wood sliding or wood

casement windows

1.For wood frame casement windows, it is necessary to construct a

frame, using at least 1 " thick wood with a 15 1/2" wide opening.

2.Paint frame and fasten it securely, sealing it into window opening.

3.Install unit into frame following procedures for metal sliding and

casement windows.

These installations are also typical, and since styles and sizes of

casement windows vary widely, it is advisable to have unit installed

by someone skilled in this type of installation. The dealer selling these

units can recommend or supply qualified people to install your new unit.

Caution: Do not block air circulationto outside louvers

of cabinet.

3/8” long screws

Drilled holes

Speed clips

Channel

Foam seal

Window channel frame

Support platform

Drilled holes

Bottom bar

3/8” long screws

12.Install speed clipson top andbottom inside edgeof window

to provide locking.(Seefig. F)

13.Using supplied plastic foam seal, cut to proper length,

insert between inside window sash and outside window.

(See fig. F)

14.Place top retainer on top edge of filler panel,then place

the bottom edgeof filler panel into groove ofbottom retainer

(mounted on unit).Filler panel may be trimmed with knife or

scissors to fitwindow height.(See fig. D)

15.Slide sliders upward making sure filler panel aligns in

sliders.

16.With sliders up against top retainer, drill 1/8"hole through

window frame inalignment with existing hole in slider. Install

3/8" long self-threading screw in hole. Repeat for other

slider.

17.Check all seals and plug for air leaks around unit. Use

sealant to fillany minor openings.

The above installationsare intended tobe permanent, and

when installed in apartment or rental properties,

permission to make the above modifications should be

obtained from owners or landlords of buildings prior to

installation of unit.

Other manuals for FAK127P1V

Table of contents

Other Frigidaire Air Conditioner manuals

Frigidaire

Frigidaire FAK104R1V 10,000 User manual

Frigidaire

Frigidaire FRP12ETT2R User manual

Frigidaire

Frigidaire FFRE0533S1E0 User manual

Frigidaire

Frigidaire CRA065AT711 Owner's manual

Frigidaire

Frigidaire CRA144HT212 User manual

Frigidaire

Frigidaire FAC083K7A5 User manual

Frigidaire

Frigidaire FAA082P7A User manual

Frigidaire

Frigidaire LRA107CV113 Owner's manual

Frigidaire

Frigidaire FGRC0644U1 Owner's manual

Frigidaire

Frigidaire FAH085P1T User manual

Frigidaire

Frigidaire CRA102BT110 Owner's manual

Frigidaire

Frigidaire Room Air Conditioner User manual

Frigidaire

Frigidaire FAH126J2T1 User manual

Frigidaire

Frigidaire FRA18EMT2 User manual

Frigidaire

Frigidaire FRA156MT1 User manual

Frigidaire

Frigidaire FRA12EZU2 User manual

Frigidaire

Frigidaire FAH106S1T - 10000 BTU Through-the-Wall Air... User manual

Frigidaire

Frigidaire FAC102P1A4 User manual

Frigidaire

Frigidaire FRA12EZU212 User manual

Frigidaire

Frigidaire FRA08EZT1 Quick start guide

Frigidaire

Frigidaire ROTARY CONTROL AIR CONDITIONER User manual

Frigidaire

Frigidaire FFTA1422U20 Owner's manual

Frigidaire

Frigidaire FFPA1222R1 Owner's manual

Frigidaire

Frigidaire FFRH1122U1 User manual

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Samsung

Samsung AS09HM3N user manual

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual

Webasto

Webasto Frigo Top 25 DS Instructions for use

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB operating instructions