Friedrich TEC12K34 Guide

INSTALLATION

OPERATION

WallMaster _Packaged Terminal

Air Conditioners

Packaged Terminal Heat Pumps

•Standard Unit

•Seacoast Protected Unit

•Remote Thermostat Unit

• Central Desk Control Unit

[_l,,IoHiI._.,5iIo][_]

10.

11.

12.

13.

14.

15.

Table of Contents

Page

Installation Checklist .................................................................................................... 3

Electrical Requirements ............................................................................................... 3

Chassis Installation ...................................................................................................... 4

Unit Operation ............................................................................................................... 7

Temperature Limiting Thermostat ................................................................................ 7

Heating Control ............................................................................................................. 8

Fan Cycle Switch ........................................................................................................... 8

Vent Control ................................................................................................................... 8

Air Outlet Louver ........................................................................................................... 9

Startup Checklist ........................................................................................................... 9

Routine Maintenance .................................................................................................. 10

Appendix A: Remote Thermostat ............................................................................... 11

Appendix B: Central Desk Control ............................................................................. 15

Appendix C: Electrical Wiring Options For 265 Volt Models .................................... 17

Warranty ....................................................................................................................... 18

Typical Installation

Air Outlet

Louver Control Box

Front Panel

Chassis

Flange

Filter

Return Air Louver-

.... il

Installation

Checklist Electric shock hazard.

Turn off electric power before service or installaSor

All electrical connections and circuits are installed in compli-

ance with and conform to the National Electrical Code and lo-

cal codes which have jurisdiction.

_/ Wall sleeve and condensate lines are installed correctly.

_/ Electrical power is disconnected.

_/ Condenser air inlet and outlet MUST be clear and free of obstructions.

_/ Cardboard wall sleeve support and louver weatherboard are removed.

_/ Wall sleeve foam gasket is installed (if applicable).

_/ Subbase kit or other means of structural support is required for ALL installations which project more than 8"

into room.

_/ Unit is installed in a 16"H x42"Wx 11 1/2"D wall sleeve. A sleeve baffle kit is used when installed in a sleeve

greater than 11 1/2" deep.

_/ Ensure that drapes, bed, bedspread, furniture, etc. DO NOT block either return or discharge air louvers.

_/ Condensate Drain Kits should be installed for complete condensate removal.

Read these instructions carefully and completely

before attempting installation. Unit should be

installed by qualified service personnel ONLY.

Failure to do so can result in property damage,

personal injury and/or death.

Wire Size

Fuse/Circuit

Breaker

Grounding

Receptacle

Wire Sizing

Electrical

Requirements

Use ONLY wiring size recommended for single out-

let branch circuit.

Use ONLY type and size fuse or HACR circuit

breaker.

Electric shock hazard.

Turn OFF electric power before service or installation.

All electrical connections and wiring MUST be installed

by a qualified electrician and conform to the National

Electrical Code and all local codes which have juris-

diction.

Failure to do so can result in property damage, per-

sonal injury and/or death.

Indicated on unit's rating plate (see page 4). Proper current protection to the unit is the responsibility of

the owner. NOTE: A time delay fuse is provided with 265V units.

Unit MUST be grounded from branch circuit through service cord to unit, or through separate ground

wire provided on permanently connected units. Be sure that branch circuit or general purpose outlet is

grounded.

The field supplied outlet must match plug on service cord and be within reach of service cord. Refer to

Table 1 for proper receptacle and fuse type. Do NOT alter the service cord or plug. Do NOT use an

extension cord.

Use recommended wire size given in Table 2 and install a single branch circuit. All wiring must comply

with local and national codes. NOTE: Use copper conductors only.

rl'l

Electrical Rating Tables

All 230/208 volt units are equipped with power cords.

See Appendix C on page 17 for wiring instructions on 265V units.

INOTE: Use Copper Conductors ONLY. I

Wire sizes are per NEC. Check local codes

for overseas applications.

Table1

AMPS

RECEPTACLE

MANUFACTURER

250 V Receptacles and Fuse Types

15 20 *

@30

PART NUMBERS

Hubbell

P&S

Arrow-Hart

9330

5930

GE4139-3

5700

5661 5461

5661 5871

GE4069-1 GE4182-1

5661 5861

15 20

TIME-DELAY TYPE

FUSE 30

(or HACR circuit breaker)

HACR -- Heating, Air conditioning, Refrigeration

* May be used for 15 Amp applications if fused for 15 Amp

NOTE: 265 volt units are permanently connected.

Table 2

Recommended branch circuit wire sizes*

AWG Wire size**

Nameplate

maximum circuit

breaker size

AWG --American Wire Gauge

* Single circuit from main box

** Based on copper wire, single insulated

conductor at 60°C

Chassis Installation

Check to be sure wall sleeve, grille, and drain kit are installed properly before chassis installation.

Remove weatherboard and center

support from sleeve (if still in place).

Be sure an outdoor louver is attached. Weatherboard

IImportant: Use a sleeve baffle kit if

installation is in a walt sleeve deeper

than 11 1/2".

Center Support

.... ?1'11

Suffocation hazard.

Keep bag away from babies and children.

Do NOT use in cribs, beds or playpens, Destroy

immediately after opening. This bag is NOT a toy!

Failure to do so can result in personal injury and/or

death.

CONTROL

PIN'( DOOR

2, Remove the front panel (contained in a protective

plastic bag) from chassis. Remove the bag and

dispose of it properly. Install the control door as

per instructions.

To install,follow these steps:

• Insert the control door into the front panel from the

back side of panel.

From the frontofthe panel, slide the right control

door pin into the hole on right side of the front panel.

Slide the left door pin into the slot on the left of the

front panel opening and snap it into place.

CAUTION

To avoid breaking the door or hinge pins, do not

apply excessive force when installing.

Com#reseor

Center the chassis in the pre-installed

sleeve and carefully push the chassis until

the chassis flange and gasket contact the

sleeve flange.

CAUTION

Copper refrigerant tubes are NOT

handles. Do NOT use tubing to lift

or move chassis.

Sleeve Flange

3. Remove the two chassis shipping brackets from the

corner of the shipping pallet.

Wall Sleeve

.Locate the four #10 x 1" chassis mount-

ing screws and tighten them into the clips

in the wall sleeve flange, (two per side).

Chassis Flange

If a Remote Thermostat is to be installed, proceed to Appendix A, Step 6.

If Central Desk Control is to be installed, proceed to Appendix B, Step 6.

rl'T

Install the front panel by placing the top of the

panel onto the brackets at the top of the chas-

sis. Rotate the bottom into place while locating

the service cord (or conduit) in a notch at the

bottom or sides of the front panel.

Secure the panel to the chassis with two #10 x

3/4" screws (provided). Attach the bottom

return air louver to the front panel, the louver

snaps into place. The louver can be secured in

place with two #10 x 3/4" screws, provided

(optional).

The filter is already installed in tracks in the

plastic cover.

®Place on

brackets

here

Two

each side of front

Louver Screw 9 _ Front Panel

Screw

NOTE: If the unit is mounted flush to the floor,

the service cord MUST be rerouted through the

side of the front panel closest to the receptacle.

A notch MUST be made in the front panel side

where the cord exits the unit. It is the responsibility

ofthe installer to create an exit notch. See diagram

(right) for suggested opening size and placement.

Plug the cord (if applicable) into the appropriate

receptacle. Extra cord may be coiled inside the

front panel behind the return air louver. Restore

power to the unit.

5/8" (16mm Not to

scale

.... 711

Unit Operation

Rotatethe temperaturedial in small increments in

the warmer orcooler direction.Movingthe dial

more than 1/4"at a time may overcompensateand

result in an extreme hotor cold situation.

•If Thermostat is installed,

see Appendix A, page 11.

•If Central Desk Control is

installed, see Appendix B,

page 15.

Pushbutton Switch Operation

Control

Cool

Heat

Fan Only

Off

Temp

Fan Speed

Operation

Operates unit on cooling - cooling will not

begin if room temperature is below 60 E

Operates unit on heating. Some models

do not provide this selection.

Circulates air within the room. No heating

or cooling functions.

Shuts system down.

Temperature control - maintains room

temperature at the desired setting.

Counterclockwise - warmer

Clockwise - cooler.

Selects high speed or low speed.

Standard Unit Control Panel

COOL HEAT FAN ONLY OFF

LOW

WARNER TEt4 ? C OLER

Temperature Limiting Thermostat

1. Set thermostat knob to center of dial.

2. Remove four screws holding control panel. Pult up on

thermostat knob and remove.

3. Locate the two temperature limiting screws.These screws

are factory installed for a maximum temperature range of

60-90 ° E Each hole in dial plate represents approximately

a 4° change from the adjacent hole.

4. To adjust temperature range, move temperature limiting

screws to desired location.

5. Replace knob when desired range has been set.

6. Replace control panel.

Remove Knob

EXAMPLE: To set a maximum temperature range of approxi-

mately 64 to 86° F,move screws to locations shown in diagram

at right.

Temperature

L miring Screws

rl'

Heating Control

NOTE: Heat pump models only. Heat pump equipped models use

backup electric resistance heating coils. At extremely low outdoor

ambient temperatures, the heat pump is automatically disabled and the

unit operates solely on electric resistance heat.

The heating control islocated behind the front panel at the control box

bottom and is accessible through the return air louver opening. Its

function is to allow you to set the temperature range in which the heat

pump operates. This control switches the unit heat operation between

heat pump and electric resistance heat based on the outdoor ambient

temperature. These change over temperatures are based on the

settings of this control. In most cases, the factory setting (at approxi-

mately the one o'clock position) is adequate. If you wish to change the

OMP6" 04'Z_

O r"_

EM_RGENC'¢ HEAT

CHAUFFAGE D'UR_ENCE

DE EME_GENCIA

HEATING CONTROL

COMMANDE DE CHAUFFAGE

CONTROLDELCALOR

factory set point, insert a flat bladed screwdriver into the slot and turn counterclockwise to increase the changeover set

point.

In the event of a compressor malfunction, turn the screw to the extreme counterclockwise emergency heat position. The

heater will then cycle using electric resistance heat only. Note that in the emergency heat position, the compressor is locked

out, disabling both heat pump and cooling operations. CALL A SERVICE PERSON.

Fan Cycle Switch

CYCLE DU

VENTILATEUR

CICLO DEL

VENTILADOR

CONTINUOUS

FAN

CYCLE

CICLO

The fan cycle switch islocated behind the front panel at the bottom of the

control box. It is accessible through the return air louver opening. It is

designed to operate the fan either continuously or intermittently with the

compressor or heating elements. When the switch is in the CONTINU-

OUS position, the fan will run continuously when the power switch is on.

With the fan cycle switch in the CYCLE position, the fan will run only when

the compressor or heating elements cycle on.

INOTE: For maximum comfort and temperature control, it is

recommended that this switch be set in the continuous position. I

Vent Control

OPEN

OUVERT

ABIERTA

VENT

AERATION

SALIDA (ESCAPE)

DEL AIRE CLOSED

FERM_

CERRADA

The vent control lever is located behind the front panel at the bottom of the

control box. When the lever is up, (OPEN), outside air is mixed with indoor

air. When the lever is down, (CLOSED), no outside air is admitted into

room and room air is recycled through unit.

INOTE: For peak operating efficiency the vent should remain closed. I

.... 711

Air Outlet Louver

\\\

The air outlet louver can be redirected to blow air either straight

up or at an angle into the room. To change the airflow direction,

remove the front panel, and the two screws on either side of the

louver. Reverse ends of louver and refasten.

Startup Checklist INOTE: Units are to be installed and

checked for proper function by qualified

service personnel ONLY.

Check the following:

_/ Unit is installed in compliance with all codes

and ordinances.

_/ Circuit breakers and wire sizes are correct.

_/ Filter is clean and in place.

_/ All panels are in place.

_/ Condenser air inlet and outlet free of obstruc-

tions.

_/ Operate unit 20 minutes.

_/ Controls operation OK.

_/ Owner or operator instructed on control opera-

tion and routine maintenance.

_/ Name and phone number of service company

attached to unit or noted in telephone directory.

_/ Condensate drain adequate.

Work area clean and free of debris. _/ Electrical cord is stored properly.

rl'l

11 Routine Maintenance

NOTE: Fan motor and all bearings are i

permanently sealed and do not require oiling. I

,IJ Keep air intake filter clean. A dirty filter reduces the efficiency of the system and can cause erratic performance of

controls. It can also result in damage to the heating element and compressor. The unit is provided with a washable

filter that can be cleaned with soap and water. Inspect and clean the filter at least once a month or more often as

conditions dictate. Replace as necessary with a factory approved filter. To replace, slide it up and out through the

front cover immediately in front of the discharge grille opening.

,IJ Do NOT block off outside air flow. Efficient operation of the unit depends on free circulation of air over the indoor and

outdoor coils. Paper, leaves and other debris can reduce efficiency and cause serious damage to the compressor.

,IJ Coils should be inspected periodically for buildup of lint, dirt, leaves, other debris and bent fins. Clean coils with a soft

brush and compressed air or vacuum. Do NOT use sharp objects to clean coils.

,IJ Do NOT operate unit with front panel removed or without filter.

,IJ Ensure that objects such as drapes, furniture, or plants are not blocking free air flow of unit.

,IJ Keep doors and windows closed. Leaving them open will increase the work load on the unit and will result in higher

operating cost and excessive condensate.

,IJ Do NOT operate the unit during construction. Construction dust can clog filter and cause permanent damage to

other components.

,IJ Apply silicon based lubricant to the belt drive system as needed. DO NOT USE ANY SOLVENT BASED LUBRICANTS

SUCH AS WD-40 TM.

Apply silicon-based

lubricant to belt located

inside access door.

il Tel

This manual suits for next models

Table of contents

Other Friedrich Air Conditioner manuals

Friedrich

Friedrich WALLMASTER WMPTAC02 User manual

Friedrich

Friedrich WallMaster PTAC User manual

Friedrich

Friedrich Vert-I-Pak A-Series User manual

Friedrich

Friedrich CP05N10 User manual

Friedrich

Friedrich Twintemp EL36 User manual

Friedrich

Friedrich MW18TC3E User manual

Friedrich

Friedrich QStar SQ06 User manual

Friedrich

Friedrich X-Star XQ05L10A User manual

Friedrich

Friedrich Chill Premier Series Guide

Friedrich

Friedrich MRM18Y3J User manual

Friedrich

Friedrich M18YJ User manual

Friedrich

Friedrich ZStar ZQ05A10B Building instructions

Friedrich

Friedrich MWM18Y3J User manual

Friedrich

Friedrich MD12Y3JM User manual

Friedrich

Friedrich PTAC ZONEAIRE PREMIER Guide

Friedrich

Friedrich MC12Y3JM User manual

Friedrich

Friedrich Uni-Fit US08C10 Building instructions

Friedrich

Friedrich M18CF User manual

Friedrich

Friedrich MWM18Y3J User manual

Friedrich

Friedrich QUIETMASTER 2008 User manual

Friedrich

Friedrich Vert-I-Pak A-Series User manual

Friedrich

Friedrich YS09J10 Guide

Friedrich

Friedrich 9370937039-02 User manual

Friedrich

Friedrich FPHFR9A3A Guide

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual