Franke FF-2000 Series User manual
FF 2000 SERIES
Pull-Out Spray Faucet
Installation guide
1/8
PARTS LIST
G 19321.XX Handle
G R0240.XX Ring cap kit
G 1154 Cartridge
G R0356031 Fastening set (rubber washer, triangular flange, metal washer, threaded nut)
G 1463 Flexible hose
G 1592.XX Spray head complete
G 1636 Counter weight
G 1534 Aerator
G R1403 Valve-holder
TECHNICAL DATA
Maximum water flow 2.2 gpm - 60 PSI
Recommended presure range 25-100 PSI - Over 100 PSI PRV required
Complies with Proposition 65, NSF 61, UPC and C-UPC requirements.
ENGLISH
Faucet installation
1. Remove all contents from the package and check for completeness (see itemized
table and picture).
NOTE:
Call us immediately if you see inconsistencies. (1-800-626-5771)
or visit
www.frankeksd.com
www.franke-canada.ca
TABLE OF CONTENT
1 Faucet
2 Spray head
3 Counter weight and gaskets
4 Fastening set (rubber washer, triangular flange, metal washer, threaded nut)
5 Hexagonal wrench
6 Valve-holder
2/8
3/8
4. Install the mounting hardware (GR0356031) to the threaded shank in the fol-
lowing sequence:
1 - round flat fiber washer
2 - triangular shaped plastic support
3 - flat metal washer
4 - thread brass nut
5. Assure that the handle and spout are properly aligned in forward position
6. Tighten the brass nut (4) with the provided wrench or use other professional
tools.
NOTE:
Solid surface installation: The sub-countertop mounting surface needs to be flat and
free of debris; otherwise the faucet will not sit properly.
Tile installation: Avoid installations near or on top of grout lines. The faucet will not
sit secure when sitting on such.
Insert the spray hose (WITHOUT HEAD) into the faucet spout and pull it all the way
through.
2. Remove all mounting hardware from protective plastic bag.
3. Place the large O-ring over the faucet shank and place the faucet into the desired
location
NOTE:
The rubber O-ring should be sitting on top of the countertop and between the faucet
body. DO NOT use putty or other sealant at this location
4/8
7. Attach the valve-holder to the shorter tubing and
attach the spray hose to the valve-holder.
NOTE:
The provided small black rubber washer needs to be installed here.
DO NOT use putty or other sealant agents at this joint.
8. Attach approved connector hoses to the two longer copper tubes and connect to
water supply valves.
WARNING!
Do not allow the supply tubes to twist or bend sharply.
NOTE:
It is recommended to use approved stainless steel braided supplies.
9. Flush out debris from water lines and faucet.
1. Pull spray hose out of the faucet spout and point the open end towards the
sink drain.
2. Open faucet handle - cold side first - by turning handle to the right and mov-
ing it upward
3. Let the faucet run on cold for 15 to 30 seconds.
4. Open faucet handle - hot side second - by turning handle to the left and mov-
ing it upward.
5. Let the faucet run on cold for 15 to 30 seconds.
6. Turn faucet off.
7. Test for leaks under the cabinet.
400 mm
5/8
10. Assemble Pull-out Spray.
1. Attach the pull-out spray head to the hose.
NOTE:
The rubber washer needs to be installed to prevent leakage.
2. Fasten the weight to the hose as shown in picture below..
3. Test all water lines, fitting and connections for leaks.
400 mm
6/8
Standard maintenance and trouble shooting
Cleaning of the spray head
Any deposits which may accumulate on the nozzle can be removed by simply running
a finger over the rubber extrusions and then running the water for a few seconds. In ex-
treme cases this step may have to be repeated.
Replacing the Cartridge
1. Shut off the water supply to the faucet.
2. Open the faucet briefly to relief any pressure inside the faucet.
3. Move the faucet handle to the “OFF” position.
4. Use a the provided allen key to loosen the set screw which is accessible
from the back of the handle.
5. Lift the handle from the cartridge.
6. Find the small notch at the base of the chrome ring cap and carefully pry
up against this to remove the cap.
7. Remove the brass retaining ring.
8. Lift out the cartridge.
9. Ensure that the seats and O-rings are in good condition
10. Remove potential mineral deposits from inside the faucet body.
11. Install the new cartridge so that the central pivots fit into the corresponding
seats.
13. Re-assemble faucet in reverse order.
14. Test for leakage.
7/8
General maintenance
Clean aerator periodically.
Do not use harsh detergents, solvents, chemical agents, steel wool, etc. that could harm
the surface.
Clean only with a soft sponge and soapy water.
In the case of very hard water, it is necessary to clean and dry the faucet after each use.
Calcium deposits could damage the surface.
Limited lifetime warranty
Franke Consumer Products, Inc., Kitchen Systems Division extends the following warranty to the origi-
nal purchaser of its faucets effective January 1, 2003.
All faucets installed in a private residence will carry a limited lifetime warranty on all mechanical
parts to be free of manufacturing defects in material and workmanship under normal usage. All chrome
finishes carry a limited lifetime warranty; all other finishes are warranted for five (5) years form the
original date of purchase.
Marine Installation: All products in a marine installation will carry a limited lifetime warranty on all
mechanical parts to be free of manufacturing defects in material and workmanship under normal usage.
All chrome products carry a limited lifetime warranty on the finish; all other finishes carry a three-year
(3) warranty from the original date of purchase.
This warranty applies only to the original owner, providing the product has been installed in accordance
with our installation instructions, used as recommended and in a normal residential application. In the
event of a warranty claim, the owner will be required to provide proof of purchase - save sales
receipt. This warranty covers all components which make the product operational. Franke, at its option,
may repair or replace the product or components necessary to restore the product to good working con-
dition. Franke reserves the right to inspect the installation prior to the actual replacement of the product
or component part.
This warranty does not cover misuse or abuse, accidental damages, scuffs or scratches, improper instal-
lation, abnormal usage, negligence or damage caused by improper maintenance or cleaning. Normal
wear of parts is excluded from the warranty. Damage caused by impurities or acts beyond our control
are not covered. Any product or part which has been repaired or altered in any manner outside of Fran-
ke’s factory, unless previously authorized in writing by Franke, will void warranty. Any replacement
excludes transportation and any labor re-installation costs. This warranty does not allow recovery of
incidental or consequential damages such as loss of use, delay, property damage or other consequential
damage, and Franke accepts no liability for such damages.
The Franke warranty is limited to the above conditions and to the warranty period specified herein and is
exclusive. Franke DISCLAIMS all other warranties, expressed or implied, including IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND/OR FITNESS FOR AS PARTICULAR PURPOSE. This
warranty gives you specific legal rights that may vary from state to state.
Further information
For any further information about our products, about the installation
of them or about the guarantee, please dial the number of the
customer service:
Phone number +1-215-822-6590
Or: 1-800-626-5771
Fax number + 1-215-822-5873
8/8
Franke Consumer Products Inc. - Kitchen Systems Division
3050 Campus Drive, Suite 500 Hatfield, PA 19440
Phone number 877-6FRANKE
Fax number 866-527-5145 Franke
1000 Kindred Road, Midland, Ontario, L4R4K9
1/8
PARTS LIST
G 19321.XX Poignée
G R0240.XX Anneau de fixage
G 1154 Cartouche
G R0356031 Set de fixation (joint en gomme, bride triangulaire, bride en métal, joint fileté)
G 1463 Flexible
G 1592.XX Douchette complète
G 1663 Contrepoids
G 1534 Aérateur
G R1403 Porte-vanne
INFORMATIONS TECNHIQUES
Consommation maximum d’eau : 2.2gpm ‘60PSI
Intervalle conseillé de pression : 25-100 PSI – au-delà de 100 PSI
Conformée à Proposition 65, NSF 61, UPC et C-UPC conditions.
FRANÇAIS
Table of contents
Languages:
Other Franke Plumbing Product manuals
Franke
Franke CAMPUS CMPX401N User manual
Franke
Franke F5 Series User manual
Franke
Franke F3 Series User manual
Franke
Franke AQUA 555 User manual
Franke
Franke F5L-Therm User manual
Franke
Franke DVS AT99-102 User manual
Franke
Franke TA 9102 FLEX Product information sheet
Franke
Franke F5S User manual
Franke
Franke 7612982001864 User manual
Franke
Franke SIRIUS BS302 User manual
Franke
Franke F3 Series User manual
Franke
Franke PLANAR 8 User manual
Franke
Franke F5 ACXT2001 User manual
Franke
Franke EXOS0009 User manual
Franke
Franke F5SM2003 User manual
Franke
Franke CAMPUS CMPX538WF User manual
Franke
Franke ORCA FF-3000 Series User manual
Franke
Franke F3 ASSV1005 User manual
Franke
Franke F5 Series User manual
Franke
Franke F5LT2003 User manual
Popular Plumbing Product manuals by other brands
Weka
Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS
Kohler
Kohler K-6228 Installation and care guide
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Operator's manual
American Standard
American Standard DetectLink 6072121 manual
Uponor
Uponor Contec TS Mounting instructions
Pfister
Pfister Selia 49-SL Quick installation guide
Kohler
Kohler Centerset K-15240 Homeowner's guide
Viega
Viega Prevista Dry 8522.33 Instructions for use
Sanela
Sanela Lema SLP 59RB Instructions for use
Elkay
Elkay EDF15AC Installation, care & use manual
Hans Grohe
Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions
baliv
baliv WT-140 manual