Focal Point Rivenhall DS-EHS01-41E Assembly Instructions

Focal Point Fires Ltd.

RBK House, Irishtown, Athlone,

Co. Westmeath, N37 XP52, Ireland

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e: [email protected]

Revision B-11/21

Rivenhall White - DS-EHS01-41E

Rivenhall Black - DS-EHS01-39E

WALL MOUNTED OR FLOOR MOUNTED LED ELECTRIC FIRE

2021

MODELS SHOWN: RIVENHALL LED ELECTRIC SUITE

2021

24 kg

H600x W1000 x D265(mm)

1.80

RIVENHALL WHITE - DS-EHS01-41E

RIVENHALL BLACK - DS-EHS01-39E

2021

Recess any part of the appliance into the wall, or run the supply cable under carpets

Site in a position where curtains or drapes could cover the appliance , or other soft materials could cover e.g. below a

coat rack

Site behind an opening door where mechanical impact/damage could occur

Site where the supply cable would become a trip hazard

Sit,stand or forcefully pull on the appliance

Obstruct,cover of force items into the openings

It should be noted that the appliance creates warm convected air currents. These currents move heat from the room

surroundings to, and up the wall surfaces adjacent to the heater.

Installing the heater next to these types of wall coverings or operating the heater where impurities in the air ,(such as

tobacco smoke) exist, may slightly discolour wall finishing.

If the appliance is to be secure on a dry lined or timber framed construction then the integrity and ability of the wall

to secure the appliance must be confirmed. It is important in these circumstances that any vapour barrier and or

structural members of the house frame are not damaged.

If you are unsure of the ability of the wall to secure the appliance and or which type of wall fixing to use, you should

take professional advice and obtain the correct fixings. Alternatively , find a more suitable wall location.

DO NOT

1 Heater unit

2 L shape brackets

1 Long bracket

7 Wall fixing screws

7 Wall plugs

2 Firebox screws

0.0003

2021

A 4x30mm x 7pcs

C 4x12mm x 2pcs

B 6mm x 7pcs

568

400 1. Ensure the wall fixing brackets are level.

2. Mark out the 7 hole locations.

3. Drill 7 holes (6mm diameter, 40mm

deep) into the wall.

Please refer to the diagram for hole

locations.

For wall mounted installations

Please note: Before drilling into walls,

always check that there are no hidden

wires, pipes, etc.Make sure that screws

and wall plugs supplied are suitable for

supporting the unit in your surface.

Consult a qualified person if you are not

sure.

Insert the supplied wall plugs (B) into the

drilled holes.

Offer the brackets into position and screw

into place with the wall screws (A) provided.

Carefully lift the appliance onto the top

bracket.

Screw the 2 appliance screws (C) into

position underneath the appliance, securing

the appliance in place.

For floor mounted installations

Please note: Before drilling into walls,

always check that there are no hidden

wires, pipes, etc.Make sure that screws

and wall plugs supplied are suitable for

supporting the unit in your surface.

Consult a qualified person if you are

not sure.

Offer the appliance up to the wall in it's

desired location.

Draw a mark where you wish to connect

the strap to the wall.

2021

5. Flame effect

6. Fire ON/OFF

7. Power Switch

DOWN

LIGHT

NOTE: press

1.Mantel

2.Logs

3.Remote control

4.Heat settings 8. LED Downlights

button (5) 3 seconds to turn on the downlights function.

Remove the appliance from the position and

drill a 1x hole (6mm diameter, 40mm deep)

Gently hammer the wall plug into position.

Carefully lift the appliance back into position.

Using a screwdriver, screw through the fixing

strap and into the wall plug you have just

installed into the wall. Securing the appliance

into place.

2021

DOWN

LIGHT

LED Display

Up Selection

Down Selection

Open Window/Door detection

Heat II

Heat I

“-” Selection“+” Selection

Downlights

Flame Effect

Timer ON/OFF

Power ON/OFF

Timer Set

Date Time Setting

Clear button

127( Before using any operation with the remote control, Insert 2 x AAA batteries to the back of the remote control.

The remote control will not respond until the digital display is illuminated as it is in sleep mode.Before operating ,

press any button once to illuminate the digital display in order to activate the remote control.

Do not press the remote control buttons more than once within two seconds for correct operation.Please wait for the

receiver to respond to the transmitter

0DQXDO2SHUDWLRQ

67(3: Plug in and turn the mains power supply on.

67(3 Turn the switch on the right hand side of the heater outlet to ³I´position.

67(3 Press the button to turn on the appliance.

67(3Press the button once to activate the low heat setting , press it again to activate the high heat setting,

press it a third time to switch the heat setting off.

67(3 To change the flame brightness , press the button to cycle through the brightness options.Turn

off the LED flame effect by pressing the button repeatedly until the flame effect cycles off.

127( press button 3 seconds to turn on the downlights function.

67(3 Activate the standby mode by pressling the button again.

67(3Switch the fire off by turning the switch on the right hand side of the heater to the ³0´position.

5HPRWH&RQWURO2SHUDWLRQ

67(3: Switch on the appliance using the switch.

67(3 Press the power button on the remote control; the LCD display will illuminate.

67(3 Press³)/$0(´button on the remote control to select the desired flame brightness; there are 3 different

brightness levels available.

67(3Select the desired heat output by pressing the relevant heat setting button:

To activate the low heat setting, press³+($7O´press it again to turn it off.

To activate the high heat setting, press³+($7OO´press it again to turn it off.

STEP 5: Press the "+" button on the remote control to increase the set temperature.

Press the "-" button to decrease the set temperature. The temperature can be set beweet 15-30℃.

If the room temperature is higher than the set temperature on the appliance, the heat will turn off.

If there is no operation for a few seconds, the remote control will show room temperature.

6HWWLQJWKH&XUUHQW'D\DQG7LPH

The day and time can only be set using the remote control.

67(3:Press the ³'$7(7,0(´button on the remote control , the day of the week will flash, Use the up and down

buttons to set the day of the week.Once the current day is set , press the “'$7(7,0(” button to confirm the current day.

67(3 The hour setting will then flash once the day has been selected .Use“”or “” to adjust the time until the current hour is

selected.Press the “'$7(7,0(” button to confirm the current hour.

67(3Then the minute setting will flash once the hour has been set.Use“”or “” to adjust the time until the current minute is

set correctly.Press the “'$7(7,0(” button to confirm the current minute.

When the window function is turned on, the temperature setting function will be disabled.

When the timer is set on, the window function will be disabled.

Safety Cut-out System

The fire suite is fitted with a thermal safety cut-out device, built in to prevent it from overheating.

Should the fire suite start to overheat, due to blocked air vents, the thermal safety cut-out system with automatically

operate and the heat settings will switch off. If this happens:

STEP 1: Switch off the fire suite using the ON/OFF switch, ensuring it is in the "O" position.

STEP 2: Check that the fire suite is unplugged from the mains power supply and allow it to cool for approximately

15 minutes.

STEP 3: Clear any blockages present on the vent,taking care not to damage the fire suite.

STEP 4: Plug in and switch on the fire suite at the mains power supply.

Caution: In order to avoid a hazard, due to inadvertent resetting of the thermal cut-out,the fire suite must not be

supplied through an external switching device such as a timer, or connected to a circuit that is regularly switched

on and off by the product.

NOTE: TIMER ON logo showed on the handset screen indicates that the weekly timer is enabled, the fire will operate

according to the set time. If you want to operate the fire manually press the TIMER ON/OFF button to turn off the weekly

timer.

The fire heater will operate to the set temperature when the weekly time is turned on, if you press any of the following

buttons “DOWN LIGHT”, “WINDOW”, ”+”, ”-“, “FLAME”, “HEAT I” and “HEAT II”.

NOTE: If the sensor fault of shortcut and open circuit, the indicator light on and button on the appliance will

blink in the same time. If the fault is removed, the indicator light on and button on the appliance stop blink.

‘

This manual suits for next models

Table of contents

Other Focal Point Indoor Fireplace manuals

Focal Point

Focal Point JEMEZ User guide

Focal Point

Focal Point HORIZON Guide

Focal Point

Focal Point MALMESBURY LED ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point ATHERSTONE SLATE ELECTRIC SUITE Assembly Instructions

Focal Point

Focal Point EF461L-E Assembly Instructions

Focal Point

Focal Point eko 3040 Guide

Focal Point

Focal Point LJSF4009E-EHS88 Assembly Instructions

Focal Point

Focal Point REFLECTION Guide

Focal Point

Focal Point GRANGE MULTIFLUE Assembly Instructions

Focal Point

Focal Point SLIMLINE EVOKE Assembly Instructions

Focal Point

Focal Point BLENHEIM LCD INSET ELECTRIC FIRE Assembly Instructions

Focal Point

Focal Point oregon User guide

Focal Point

Focal Point F500056 Assembly Instructions

Focal Point

Focal Point L23 CHESHIRE Guide

Focal Point

Focal Point Fireglo Slimline User guide

Focal Point

Focal Point POLARIS User manual

Focal Point

Focal Point Exselsior Slimline User manual

Focal Point

Focal Point Envy Guide

Focal Point

Focal Point OBLIQUE Guide

Focal Point

Focal Point HORIZON Assembly Instructions

Focal Point

Focal Point L23S MIDNIGHT Assembly Instructions

Focal Point

Focal Point L40 PINOIR- NG Assembly Instructions

Focal Point

Focal Point Excelsior Expanse Guide

Focal Point

Focal Point BLENHEIM Assembly Instructions

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual