Exsys EX-3508 User manual

1

EX-3508

8-Port SATA II PCI-Express Controller (Non-RAID)

1. Introduction

Thank you for purchasing this 8-Port SATA2 PCI PCIe Card (non-RAID). It is

designed to support up to 8 SATA2 ports with 2 built-in SATA2 Port Multipliers

(PMs). It supports 8 SATA2 devices over one single PCI Express Slot. It is an

ideal solution to add more SATA drives for your system.

Features:

√ Supports 1-lane 2.5Gb/s PCI Express Data Transfer Rate

√ Built-in 2 SATA2 Port Multipliers (PM)

√ Provides 8 Ports (with 4 Double-deck Connectors) for 8 Internal SATA2

Devices

√ Non-RAID Support, Only Boot from Port 1 and Port 4

√ Supports SATA2 transfer rate of 3.0Gb/s (300Mbytes/sec)

√ Supports Native Command Queuing (NCQ)

√ Supports Windows 2000, XP, Vista and Win 7

2. Layout

JP1 BIOS Enable/

Disable Jumper

J4:

Up: Port 5

Down: Port 6

J5:

Up: Port 7

Down: Port 8

J2:

Up: Port 1

Down: Port 2

J3:

Up: Port 3

Down: Port 4

Extra secure

mounting holes

2

8-Port SATA II PCI-Express Controller

3. Jumper Settings

JP1: BIOS Enable/Disable Jumper

4. Driver Location on the CD

Note:

Due to the limitation of the Port Multipliers, only Port 1

and Port 4 can be the System Boot Drives. Other ports won’t

support Boot function.

DIS ENA

BIOS Enabled:

Jumper Installed at “ENA”

(Default)

DIS ENA

BIOS Disabled:

Jumper Installed at “DIS”

1. Power down the peripherals, then the computer.

2. Remove the computer cover and save the screws.

3. Choose an unused PCI Express bus slot.

4. Unscrew and remove the slot cover. Retain the screw; you will use it when you

install the SATA2 PCIe Card.

5. Place the SATA2 PCIe Card into the slot. Carefully press the board into the slot

until it seats firmly.

6. Secure the SATA2 PCIe Card with the slot cover screw.

7. Install the internal SATA cables from the SATA connectors to your SATA devic-

es.

8. Carefully reinstall the computer cover. Insert and tighten the computer cover

screws.

9. Power up the PC and observe the monitor. The BIOS lists all Serial ATA devices

attached to the SATA2 PCIe Card. For example:

SiI 3132 SATA BIOS Version x.x.xx

Copyright (C) 1997-2005 Silicon Image, Inc.

0 HDS728080PLA380 76 GB

1 HDS728080PLA380 76 GB

If the information displayed on your monitor is correct (the installed devices are

listed with the correct device name, etc.), congratulations! You have successfully

installed the SATA2 PCIe Card in your computer.

3

8-Port SATA II PCI-Express Controller

5. Fresh Win2000/XP/2003/Vista/Win7 Installation

Note:

Since all the SATA drives are connected via Port Multipli-

ers, only the first (Port 1) and the fourth (Port 4) drives are

shown by the BIOS, however, after installing the Windows drivers, all

drives will be detected by Windows and works properly. If you leave the

Port 1 and Port 4 unconnected, the BIOS may take longer time to wait

them until timeout. It is strongly recommended to connect the drive from

Port 1 sequentially.

If you are performing a new installation of Windows 2000 (or XP, 2003, Vista, Win 7),

and you wish to boot from a device attached to this SATA2 PCIe card. If your drivers

are on a CD (in the drive D: for example) instead of diskette, please prepare the “Driver

Installation Disk” as follows:

COPY D: SATA nonRAID SiI3132 A:

1. Put your Windows CD into the CD-ROM/DVD drive.

2. Power up the system.

3. Press F6 for third party SCSI or driver installation at the beginning of text mode

installation. Press 's' when setup asks if you want to specify an additional de-

vice, and insert the "Driver Installation Disk" prepared as mentioned above.

4. Press 'Enter' to continue on with text mode setup.

5.

Follow the setup instructions to select your choice for partition and file system.

The setup program will continue and finish the installation after restart.

6. Existing Win2000/XP/2003/Vista/Win7 Installation

1. Boot Windows 2000/XP/2003/Vista/Win7 and logon as a user that has Adminis-

trator privileges. The Windows Installation Wizard will ask you to install the driv-

er, please follow its instruction, browse to the following folder (Windows 32-bit,

for example) and complete the installation:

D: SATA nonRAID SiI3132 32-bit

2. If your hard drive is blank, you may need to go to the Windows Device Manager

to create partitions and format the drive. If your drive’s capacity is bigger than

2TB, since the Windows’ traditional MBR partition only supports up to 2TB, you

may need to create a GPT partition instead of MBR, please check Windows’

document for more detail information.

4

8-Port SATA II PCI-Express Controller

Table of contents

Popular PCI Card manuals by other brands

ERMA

ERMA SSI 1417 instruction manual

SIIG

SIIG CyberSerial Dual PCI Software installation

Moxa Technologies

Moxa Technologies CP-102E Quick installation guide

I-Bus

I-Bus IBC2602 user guide

Chelsio Communications

Chelsio Communications T5 Series Installation and user guide

Conrad Electronic

Conrad Electronic 97 46 71 operating instructions

Micro Innovations

Micro Innovations USB650A Quick installation guide

KTI Networks

KTI Networks KF-310 user guide

Asus

Asus SpaceLink WL230 user manual

SIIG

SIIG SC2475 Quick installation guide

TRENDnet

TRENDnet TEW-703PI Quick installation guide

Belkin

Belkin F5D7000F user manual

Pericom

Pericom PI7C7100 manual

ADLINK Technology

ADLINK Technology cPCI-3548 user manual

Digium

Digium TE200 Series user manual

Allo.com

Allo.com 2nd Gen E1/T1/J1 Quick installation guide

Western Digital

Western Digital FireWire PCI Adapter installation guide

Pyle

Pyle Gamelink PLINK1 user guide